With commit 035ef06b applied, the test pop3 server needs to send
".\r\n" as the body terminating sequence and there needs to be a final
CRLF in the actual body in the test data file.

Curl_pop3_write() would drop the final CRLF of a message as it was
considered part of the EOB as opposed to part of the message. Whilst
the EOB sequence needs to be searched for by the function only the
final 3 characters should be removed as per RFC-1939 section 3.

Reported by: Rich Gray
Bug: http://curl.haxx.se/mail/lib-2012-02/0051.html

Curl_smtp_escape_eob() would leave off final CRLFs from emails ending
in multiple blank lines additionally leaving the smtpc->eob variable
with the character count in, which would cause problems for additional
emails when sent through multiple calls to curl_easy_perform() after a
CURLOPT_CONNECT_ONLY.

Make sure it is mentioned once and with the correct description

Added an extra command-line argument to support the optional AUTH
parameter in SMTPs MAIL FROM command.

Added information relating to the new CURLOPT_MAIL_AUTH parameter and
reworked CURLOPT_MAIL_FROM and CURLOPT_MAIL_RCPT to be a clearer.

Fixed inconsistencies of "vocalisation of the abbreviation" versus
"vocalisation of the first word" for all abbreviations.

Corrected a typo in CURLOPT_NOPROXY.

Fixed the use of angled brackets "<>" in the optional AUTH parameter as
per RFC-2554 section 5. The address should not include them but an
empty address should be replaced by them.

Added a new CURLOPT_MAIL_AUTH option that allows the calling program to
set the optional AUTH parameter in the MAIL FROM command.

When this option is specified and an authentication mechanism is used
to communicate with the mail server then the AUTH parameter will be
included in the MAIL FROM command. This is particularly useful when the
calling program is acting as a relay in a trusted environment and
performing server to server communication, as it allows the relaying
server to specify the address of the mailbox that was used to
authenticate and send the original email.

Modify configure.ac to test for new CyaSSL Init function and remove
default install path to system.  Change to CyaSSL OpenSSL header and
proper Init in code as well.

Note that this no longer detects or works with CyaSSL before v2

I accidentally left the lowest bits 01 before

Fixed incorrect behavior in smtp_done() which would cause the end of
block data to be sent to the SMTP server if libcurl was operating in
connect only mode. This would cause the server to return an error as
data would not be expected which in turn caused libcurl to return
CURLE_RECV_ERROR.

We will go straight to 7.25.0 due to the new additions

and updated the end year in the generic copyright string

9 bug fixes, 4 changes and numerous contributors

Bumped release version and option counters

Fix the str2num() function to not check if the input string starts with a
digit, since strtol() supports numbers prepended with '-' (and '+') too.
This makes the --max-redirs option work as documented.

... by making sure that the string is always freed after the invoke as
parse_proxy will always copy the data and this way there's a single
free() instead of multiple ones.

The proxy parser function strips off trailing slashes off the proxy name
which could lead to a mistaken zero length proxy name which would be
treated as no proxy at all by subsequent functions!

This is now detected and an error is returned. Verified by the new test
1329.

Reported by: Chandrakant Bagul
Bug: http://curl.haxx.se/mail/lib-2012-02/0000.html

... and fix some typos from the 62d15f15 commit.

This new option tells curl to not work around a security flaw in the
SSL3 and TLS1.0 protocols. It uses the new libcurl option
CURLOPT_SSL_OPTIONS with the CURLSSLOPT_ALLOW_BEAST bit set.

Allow an appliction to set libcurl specific SSL options. The first and
only options supported right now is CURLSSLOPT_ALLOW_BEAST.

It will make libcurl to disable any work-arounds the underlying SSL
library may have to address a known security flaw in the SSL3 and TLS1.0
protocol versions.

This is a reaction to us unconditionally removing that behavior after
this security advisory:

http://curl.haxx.se/docs/adv_20120124B.html

... it did however cause a lot of programs to fail because of old
servers not liking this work-around. Now programs can opt to decrease
the security in order to interoperate with old servers better.

Use the new library CURLOPT_TCP_KEEPALIVE rather than disabling this via
the sockopt callback. If --keepalive-time is used, apply the value to
CURLOPT_TCP_KEEPIDLE and CURLOPT_TCP_KEEPINTVL.

This adds three new options to control the behavior of TCP keepalives:

- CURLOPT_TCP_KEEPALIVE: enable/disable probes
- CURLOPT_TCP_KEEPIDLE: idle time before sending first probe
- CURLOPT_TCP_KEEPINTVL: delay between successive probes

While not all operating systems support the TCP_KEEPIDLE and
TCP_KEEPINTVL knobs, the library will still allow these options to be
set by clients, silently ignoring the values.

When CURLOPT_REFERER has been used, curl_easy_reset() did not properly
clear it.

Verified with the new test 598

Bug: http://curl.haxx.se/bug/view.cgi?id=3481551
Reported by: Michael Day

This prevents clobbering of non recoverable error return codes while
retaining intended functionality of commit 65103efe

We want to continue to the next URL to try even on failures returned
from libcurl. This makes -f with ranges still get subsequent URLs even
if occasional ones return error. This was a regression as it used to
work and broke in the 7.23.0 release.

Added test case 1328 to verify the fix.

Bug: http://curl.haxx.se/bug/view.cgi?id=3481223
Reported by: Juan Barreto

When the target host was given as a IPv6 numerical address, it was not
properly put within square brackets for the Host: header in the CONNECT
request. The "normal" request did fine.

Reported by: "zooloo"
Bug: http://curl.haxx.se/bug/view.cgi?id=3482093

When support for nettle was added in 64f328c7, I overlooked
the fact that AC_CHECK_LIB doesn't add the tested lib to LIBS
if the check succeeded, if a custom success code block was present.
(The previous version of the check had an empty block for
successful checks, adding the lib to LIBS implicitly.)

Therefore, explicitly add either nettle or gcrypt to LIBS, after
deciding which one to use. Even if they can be linked in
transitively, it is safer to actually link explicitly to them.

This fixes building with gnutls with linkers that don't allow
linking transitively, such as for windows.

When connecting to a domain with multiple IP addresses, allow different,
decreasing connection timeout values. This should guarantee some
connections attempts with sufficiently long timeouts, while still
providing fallback.