"git@forge.etsi.org:cim/ngsi-ld-test-suite.git" did not exist on "368b2766f68f15d08ee13f6c00a02f5ba82be8a9"
Newer
Older
/**
* @author TTF 010
* @version $Id: $
* @desc This module provides ATS specific test case definitions for IMS Emergency calls.
* @see ETSI TS 103 795-2
*/
module AtsImsIot_Emergency {
// LibCommon
// LibSip
// LibIms
import from LibIot_TestInterface all;
import from LibIot_TestConfiguration all;
import from LibIot_PIXITS all;
import from LibIot_VxLTE_PIXITS all;
import from LibIot_VxLTE_Functions all;
// LibImsIot
import from AtsImsIot_TestConfiguration all;
import from AtsImsIot_TestSystem all;
import from AtsImsIot_Functions all;
import from AtsImsIot_Templates all;
import from AtsImsIot_TP_behavior_GM all;
import from AtsImsIot_TP_behavior_MW_PS all;
import from AtsImsIot_TP_behavior_MW_SI all;
import from AtsImsIot_TP_behavior_MW_IS all;
Yann Garcia
committed
import from AtsImsIot_TP_behavior_MX all;
import from AtsImsIot_TP_behavior_MM all;
import from AtsImsIot_TP_behavior_ML all;
import from AtsImsIot_TP_behavior_IC all;
import from AtsImsIot_TP_behavior_CX all;
import from AtsImsIot_TP_behavior_GX all;
import from AtsImsIot_TP_behavior_ISC all;
import from AtsImsIot_TP_behavior_S6A all;
import from AtsImsIot_TP_behavior_S9 all;
import from AtsImsIot_TP_behavior_SH all;
import from AtsImsIot_TP_behavior_RX all;
// For Diameter codec tests only
import from LibDiameter_TypesAndValues all;
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5 Test Descriptions (Interoperability at HPLMN)
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5.1 Network Attachment
*/
group NetworkAttachment {
group UENetworkAttachmentWithUSIM {
Yann Garcia
committed
/**
* @desc UE Emergency Network Attachment and Establishment of the Emergency Bearer with USIM.
Yann Garcia
committed
* On successful emergency attachment, the UE/IVS should discover the P-CSCF IP address.
* The EPC will create the Emergency Bearers which will allow communication only between the UE and the P-CSCF
* and allowed forwarding towards E-CSCF
* @see ETSI TS 103 795-2 Clause 5.1.1
* TS 124 229 [2], clause 9.2.1 and L.2.2.6; TS 129 212 [7], clauses 4.5.15 and 4a.5.12;
Yann Garcia
committed
* TS 129 272 [8], clause 5.2.1.1 (MME shall proceed even if Update Location fails)
*
*/
testcase TC_VoLTE_ECO_INT_ATT_01 ( ) runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A );
// f_validate_uar('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'O);
// stop;
Yann Garcia
committed
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_DIAMETER_GX_INTERFACENAME,PX_DIAMETER_S6A_INTERFACENAME})){
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_VxLteMonitor_Up();
// preamble
f_mtc_userRadioEnabled ( v_ueA, true, true ); // UA-A trigger an initial network_attachment by enabling radio interface of its mobile
// test body
// Check that user A starts initial network attachment
f_mtc_check_TP_S6A_MME_ULR_01 ( vc_vxlte_monitor_components.s6a, true ); // Check (ULR – Event 2)
f_mtc_check_TP_S6A_HSS_ECO_ULA_01 ( vc_vxlte_monitor_components.s6a); // Check (ULA – Event 3)
f_mtc_check_TP_GX_PCRF_ECO_CCA_01 ( vc_vxlte_monitor_components.gx); // Check (CCR, CCA – Events 4, 5)
// postamble
f_mtc_userRadioEnabled ( v_ueA, false, true );
//unmap/disconnect component ports
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
} // End of TC TC_VoLTE_ECO_INT_ATT_01
// function f_validate_uar(in octetstring p_uar) {
// var bitstring v_conv := oct2bit(p_uar);
// var UAR_MSG v_msg;
// var integer v_result := decvalue(v_conv, v_msg);
// log("msg: ", v_msg);
// if (v_result == 0) {
// var octetstring v_uar_enc := bit2oct(encvalue(v_msg));
// log("v_uar_enc: ", v_uar_enc);
// log("Matching v_uar_enc: ", match(p_uar, v_uar_enc));
// if (match(p_uar, v_uar_enc)) {
// setverdict(pass);
// } else {
// setverdict(fail);
// }
// } else {
// setverdict(fail);
// }
// stop;
// }
} // End of group UENetworkAttachmentWithUSIM
group UENetworkAttachmentWithoutUSIM {
Yann Garcia
committed
/**
* @desc UE Emergency Network Attachment and Establishment of the Emergency Bearer without USIM.
Yann Garcia
committed
* On successful emergency attachment, the UE/IVS should discover the P-CSCF IP address.
* The EPC will create the Emergency Bearers which will allow communication only between the UE and the P-CSCF
* and allowed forwarding towards E-CSCF
* @see ETSI TS 103 795-2 Clause 5.1.2
* TS 124 229 [2], clause 9.2.1 and L.2.2.6; TS 129 212 [7], clauses 4.5.15 and 4a.5.12;
Yann Garcia
committed
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
* TS 129 272 [8], clause 5.2.1.1 (MME shall proceed even if Update Location fails)
*
*/
testcase TC_VoLTE_EMC_INT_ATT_02 ( ) runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_DIAMETER_GX_INTERFACENAME,PX_DIAMETER_S6A_INTERFACENAME})){
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_VxLteMonitor_Up();
// preamble
f_mtc_userRadioEnabled ( v_ueA, true, true ); // UA-A trigger an initial network_attachment by enabling radio interface of its mobile
// test body
// Check that user A starts initial network attachment
f_mtc_check_TP_S6A_MME_ULR_01 ( vc_vxlte_monitor_components.s6a, true ); // Check (ULR – Event 2)
f_mtc_check_TP_S6A_HSS_ECO_ULA_01 ( vc_vxlte_monitor_components.s6a); // Check (ULA – Event 3)
f_mtc_check_TP_GX_PCRF_EMC_CCA_01 ( vc_vxlte_monitor_components.gx); // Check (CCR, CCA – Events 4, 5)
// postamble
f_mtc_userRadioEnabled ( v_ueA, false, true );
//unmap/disconnect component ports
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
} // End of TC TC_VoLTE_ECO_INT_ATT_02
} // End of group UENetworkAttachmentWithoutUSIM
} // End of group NetworkAttachment
/**
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5.2 IMS Emergency Registration
*/
group EmergencyRegistration {
/**
* @desc To perform emergency registration via the established emergency bearer. Note that some UEs perform emergency registration automatically on attachment - in which case this test becomes merged with the previous ones.
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5.2.1 IMS Emergency Registration - Successful
*/
testcase TD_VoLTE_ECO_INT_REG_01() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var ImsUserInfo v_userInfoA := f_getSipUserId ( PX_EUT_A_EMERGENCY );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_SIP_MW_PI_INTERFACENAME,
PX_SIP_MW_IS_INTERFACENAME,
PX_DIAMETER_CX_SH_INTERFACENAME,
PX_DIAMETER_CX_IH_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME}))
{
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_VxLteMonitor_Up();
// preamble
f_mtc_userRadioEnabled ( v_ueA, true, true ); // UA-A trigger an initial network_attachment by enabling radio interface of its mobile
f_mtc_check_TP_GM_PCSCF_ECO_REGISTER_01(vc_vxlte_monitor_components.gmA); // Events 1, 12
f_mtc_check_TP_MW_PCSCF_ECO_REGISTER_01(vc_vxlte_monitor_components.mwPI); // Event 4, 11
f_mtc_check_TP_MW_ICSCF_ECO_REGISTER_01(vc_vxlte_monitor_components.mwIS, true); // Event 7, 10
f_mtc_check_TP_CX_HSS_ECO_UAA_01(f_getCxInterface(PX_DIAMETER_CX_SINGLE_INTERFACE));// Event 5, 6
f_mtc_check_TP_CX_HSS_MAA_01(vc_vxlte_monitor_components.cxSH);// Event 8, 9
f_mtc_check_TP_GM_PCSCF_ECO_REGISTER_02(vc_vxlte_monitor_components.gmA); // Events 13, 22
f_mtc_check_TP_MW_PCSCF_ECO_REGISTER_02(vc_vxlte_monitor_components.mwPI); // Events 14, 21
f_mtc_check_TP_MW_ICSCF_ECO_REGISTER_02(vc_vxlte_monitor_components.mwIS, true); // Event 17, 20
f_mtc_check_TP_CX_HSS_ECO_UAA_02(f_getCxInterface(PX_DIAMETER_CX_SINGLE_INTERFACE));// Event 15, 16
f_mtc_check_TP_CX_HSS_SAA_01(vc_vxlte_monitor_components.cxSH);// Event 18, 19
// postamble
f_PO_user_home_deregistration ( v_ueA );
f_mtc_userRadioEnabled ( v_ueA, false, true );
//unmap/disconnet component ports
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs");
}
} // End of testcase TD_VoLTE_ECO_INT_REG_01
/**
* @desc To attempt initial emergency registration via the established emergency bearer. In this case, the emergency registration is not successful due to not accepted UE credentials. Emergency call can be established without emergency registration.
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5.2.2 IMS Emergency Registration - Unsuccessful
*/
testcase TD_VoLTE_ECO_INT_REG_02() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var ImsUserInfo v_userInfoA := f_getSipUserId ( PX_EUT_A_EMERGENCY );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_SIP_MW_PI_INTERFACENAME,
PX_SIP_MW_IS_INTERFACENAME,
PX_DIAMETER_CX_SH_INTERFACENAME,
PX_DIAMETER_CX_IH_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME}))
{
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_VxLteMonitor_Up();
// preamble
f_mtc_userRadioEnabled ( v_ueA, true, true ); // UA-A trigger an initial network_attachment by enabling radio interface of its mobile
f_mtc_check_TP_GM_PCSCF_ECO_REGISTER_01(vc_vxlte_monitor_components.gmA); // Events 1, 12
f_mtc_check_TP_MW_PCSCF_ECO_REGISTER_01(vc_vxlte_monitor_components.mwPI); // Event 4, 11
f_mtc_check_TP_MW_ICSCF_ECO_REGISTER_01(vc_vxlte_monitor_components.mwIS, true); // Event 7, 10
f_mtc_check_TP_CX_HSS_ECO_UAA_01(f_getCxInterface(PX_DIAMETER_CX_SINGLE_INTERFACE));// Event 5, 6
f_mtc_check_TP_CX_HSS_MAA_01(vc_vxlte_monitor_components.cxSH);// Event 8, 9
f_mtc_check_TP_GM_PCSCF_ECO_REGISTER_03(vc_vxlte_monitor_components.gmA); // Events 13, 22
f_mtc_check_TP_MW_PCSCF_ECO_REGISTER_03(vc_vxlte_monitor_components.mwPI); // Events 14, 21
f_mtc_check_TP_MW_ICSCF_REGISTER_03(vc_vxlte_monitor_components.mwIS, true); // Event 17, 20
Yann Garcia
committed
f_mtc_check_TP_CX_HSS_ECO_UAA_02(f_getCxInterface(PX_DIAMETER_CX_SINGLE_INTERFACE));// Event 15, 16
f_mtc_check_TP_CX_HSS_SAA_01(vc_vxlte_monitor_components.cxSH);// Event 18, 19
// postamble
f_PO_user_home_deregistration ( v_ueA );
f_mtc_userRadioEnabled ( v_ueA, false, true );
//unmap/disconnet component ports
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs");
}
} // End of testcase TD_VoLTE_ECO_INT_REG_02
} // End of group EmergencyRegistration
/**
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5.3 Emergency Session and Emergency Bearer Operations
*/
group EmergencySessionEmergencyBearerOperations {
/**
* @see ETSI TS 103 795-2 Clause 5.3.1 Emergency Session Establishment
*/
group EmergencySessionEstablishment {
* @desc To demonstrate the establishment of dedicated bearers at the originating EPC due to SIP emergency session establishment within an emergency registration.
* PSAP is located in the IM CN subsystem of IMS A
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5.3.1.2 UE calling PSAP with emergency registration
testcase TD_VoLTE_ECO_INT_INI_01() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
if (PX_PSAP_REGISTERED) {
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_01();
Yann Garcia
committed
if (not PX_ECALL) {
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 1
} else {
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_04(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 1
}
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.gmA, -, v_sip);
//Rx/Gx exchange after INVITE (SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_03(vc_vxlte_monitor_components.rx);// Event 2
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 3
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 4
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 5
f_mtc_check_TP_RX_PCSCF_RAA_01(vc_vxlte_monitor_components.rx);// Events 7,8
f_mtc_check_TP_GX_PCRF_CCA_01(vc_vxlte_monitor_components.gx); // Events 6,9
f_mtc_check_TP_MW_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 10
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
f_mtc_check_TP_MM_ECSCF_ECO_INVITE_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 11
f_mtc_check_TP_MM_ECSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip);
f_mtc_check_TP_MM_ECSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 183 In Progress Event 12
f_mtc_check_TP_MW_PCSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 13
f_mtc_check_TP_GM_PCSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 18
//Rx/Gx exchange after 183(SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_04(vc_vxlte_monitor_components.rx);// Event 14
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 15
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 16
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 17
f_mtc_check_TP_MM_ECSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 180 Ringing – Event 20
f_mtc_check_TP_MW_PCSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 21
f_mtc_check_TP_GM_PCSCF_180RINGING_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 22
f_mtc_userCheckRinging(v_psap); // Event 19
f_mtc_userCheckPeerIsRinging(v_ueA); // Event 19
f_mtc_userAnswerCall(v_psap); // Event 26
f_mtc_check_TP_MM_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 200 OK Event 23
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 24
f_mtc_check_TP_GM_PCSCF_200OK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 25
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // ACK Event 26
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 27
f_mtc_check_TP_MM_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // ACK – Event 28
f_mtc_userCheckCallEstablished(v_ueA); // Event 29
f_mtc_userCheckCallEstablished(v_psap); // Event 29
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_INI_01
group f_TD_VoLTE_ECO_INT_INI_01 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_01() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_01
} // End of group f_TD_VoLTE_ECO_INT_INI_01
* @desc To demonstrate the establishment of dedicated bearers at the originating EPC due to SIP emergency session session establishment within non-emergency registration.
* PSAP is located in the IM CN subsystem of IMS A.
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5.3.1.3 UE calling PSAP with non-emergency registration
* @remark This is option2: IBCF is connected to the PSAP, the interface IBCF and the PSAP is the Mm interface
*/
testcase TD_VoLTE_ECO_INT_INI_02() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
if (PX_PSAP_REGISTERED) {
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_02();
// Test body
//f_mtc_userInitiateCall (v_ueA, v_userTelInfoB);
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_03(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 1
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.gmA, -, v_sip);
//Rx/Gx exchange after INVITE (SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_03(vc_vxlte_monitor_components.rx);// Event 2
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 3
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 4
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 5
f_mtc_check_TP_RX_PCSCF_RAA_01(vc_vxlte_monitor_components.rx);// Events 7,8
f_mtc_check_TP_GX_PCRF_CCA_01(vc_vxlte_monitor_components.gx); // Events 6,9
f_mtc_check_TP_MW_PCSCF_ECO_INVITE_03(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 10
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
f_mtc_check_TP_MM_ECSCF_ECO_INVITE_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 11
f_mtc_check_TP_MM_ECSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip);
// 183 Session Progress
f_mtc_check_TP_MM_ECSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 183 In Progress Event 12
f_mtc_check_TP_MW_PCSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 13
f_mtc_check_TP_GM_PCSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 18
//Rx/Gx exchange after 183(SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_04(vc_vxlte_monitor_components.rx);// Event 14
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 15
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 16
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 17
f_mtc_check_TP_MM_ECSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 180 Ringing – Event 22
f_mtc_check_TP_MW_PCSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 24
f_mtc_check_TP_GM_PCSCF_180RINGING_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 25
f_mtc_userCheckRinging(v_psap); // Event 19
f_mtc_userCheckPeerIsRinging(v_ueA); // Event 19
f_mtc_userAnswerCall(v_psap); // Event 26
f_mtc_check_TP_MM_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 200 OK Event 23
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 24
f_mtc_check_TP_GM_PCSCF_200OK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 25
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 26
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 27
f_mtc_check_TP_MM_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // ACK – Event 28
f_mtc_userCheckCallEstablished(v_ueA); // Event 29
f_mtc_userCheckCallEstablished(v_psap); // Event 29
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_INI_02
group f_TD_VoLTE_ECO_INT_INI_02 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_02() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_02
} // End of group f_TD_VoLTE_ECO_INT_INI_02
* @desc To demonstrate the establishment of emergency bearers at the originating EPC due to SIP emergency session establishment without any registration.
* PSAP is located in the IM CN subsystem of IMS A.
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5.3.1.4 UE calling PSAP without any registration
*/
testcase TD_VoLTE_ECO_INT_INI_03() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
// No registration for user A
f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_03();
// Test body
//f_mtc_userInitiateCall (v_ueA, v_userTelInfoB);
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_01(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 1
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.gmA, -, v_sip);
//Rx/Gx exchange after INVITE (SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_03(vc_vxlte_monitor_components.rx);// Event 2
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 3
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 4
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 5
f_mtc_check_TP_RX_PCSCF_RAA_01(vc_vxlte_monitor_components.rx);// Events 7,8
f_mtc_check_TP_GX_PCRF_CCA_01(vc_vxlte_monitor_components.gx); // Events 6,9
f_mtc_check_TP_MW_PCSCF_ECO_INVITE_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 10
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
f_mtc_check_TP_MM_ECSCF_ECO_INVITE_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 11
f_mtc_check_TP_MM_ECSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip);
// 183 Session Progress
f_mtc_check_TP_MM_ECSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 183 In Progress Event 12
f_mtc_check_TP_MW_PCSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 13
f_mtc_check_TP_GM_PCSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 18
//Rx/Gx exchange after 183(SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_04(vc_vxlte_monitor_components.rx);// Event 14
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 15
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 16
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 17
f_mtc_check_TP_MM_ECSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 180 Ringing – Event 22
f_mtc_check_TP_MW_PCSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 24
f_mtc_check_TP_GM_PCSCF_180RINGING_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 25
f_mtc_userCheckRinging(v_psap); // Event 19
f_mtc_userCheckPeerIsRinging(v_ueA); // Event 19
f_mtc_userAnswerCall(v_psap); // Event 26
f_mtc_check_TP_MM_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 200 OK Event 23
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 24
f_mtc_check_TP_GM_PCSCF_200OK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 25
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 26
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 27
f_mtc_check_TP_MM_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // ACK – Event 28
f_mtc_userCheckCallEstablished(v_ueA); // Event 29
f_mtc_userCheckCallEstablished(v_psap); // Event 29
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_INI_03
group f_TD_VoLTE_ECO_INT_INI_03 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_03() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_03
} // End of group f_TD_VoLTE_ECO_INT_INI_03
/**
* @desc To demonstrate the establishment of dedicated bearers at the originating EPC due to SIP emergency session establishment within an emergency registration.
* PSAP is located in the IM CN subsystem of IMS A. The PSAP URI is delivered by the LRF.
* @see ETSI TS 103 795-2 Clause 5.3.1.5 UE calling PSAP in same network, LRF derived PSAP URI
* @remark This is option2: IBCF is connected to the PSAP, the interface IBCF and the PSAP is the Mm interface
*/
testcase TD_VoLTE_ECO_INT_INI_04() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_ML_E_LRF_INTERFACENAME // E-CSCF -> LRF
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_01();
// Test body
Yann Garcia
committed
if (not(PX_ECALL)) {
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 1
} else {
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_04(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 1
}
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.gmA, -, v_sip);
//Rx/Gx exchange after INVITE (SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_03(vc_vxlte_monitor_components.rx);// Event 2
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 3
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 4
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 5
f_mtc_check_TP_RX_PCSCF_RAA_01(vc_vxlte_monitor_components.rx);// Events 7,8
f_mtc_check_TP_GX_PCRF_CCA_01(vc_vxlte_monitor_components.gx); // Events 6,9
f_mtc_check_TP_MW_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 10
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
Yann Garcia
committed
f_mtc_check_TP_ML_ECSCF_ECO_INVITE_01(vc_vxlte_monitor_components.mlE_LRF, -, v_sip); // Event 11
f_mtc_check_TP_ML_ECSCF_ECO_3xx_01(vc_vxlte_monitor_components.mlE_LRF, -, v_sip); // Event 12
f_mtc_check_TP_MM_ECSCF_ECO_INVITE_02(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 13
f_mtc_check_TP_MM_ECSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip);
f_mtc_check_TP_MM_ECSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 183 In Progress Event 14
f_mtc_check_TP_MW_PCSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 15
f_mtc_check_TP_GM_PCSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 20
//Rx/Gx exchange after 183(SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_04(vc_vxlte_monitor_components.rx);// Event 14
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 15
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 16
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 17
f_mtc_check_TP_MM_ECSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 180 Ringing – Event 22
f_mtc_check_TP_MW_PCSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 23
f_mtc_check_TP_GM_PCSCF_180RINGING_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 24
f_mtc_userCheckRinging(v_psap); // Event 21
f_mtc_userCheckPeerIsRinging(v_ueA); // Event 21
f_mtc_userAnswerCall(v_psap); // Event 28
f_mtc_check_TP_MM_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 200 OK Event 25
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 26
f_mtc_check_TP_GM_PCSCF_200OK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 27
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // ACK Event 28
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 29
f_mtc_check_TP_MM_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // ACK – Event 30
f_mtc_userCheckCallEstablished(v_ueA); // Event 31
f_mtc_userCheckCallEstablished(v_psap); // Event 31
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_INI_04
group f_TD_VoLTE_ECO_INT_INI_04 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_04() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_04
} // End of group f_TD_VoLTE_ECO_INT_INI_04
/**
* @desc To demonstrate the establishment of dedicated bearers at the originating EPC due to SIP emergency session establishment within an emergency registration.
* PSAP is located in the IM CN subsystem of another network connected via IBCF.
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5.3.1.6 UE calling PSAP in other network via IBCF
testcase TD_VoLTE_ECO_INT_INI_05 ( ) runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_IC_INTERFACENAME // IBCF -> IMS_B -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_userRegistration(v_ueA, v_userInfoA);
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_05();
// Test body
//f_mtc_userInitiateCall (v_ueA, v_userTelInfoB);
Yann Garcia
committed
if (not(PX_ECALL)) {
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 1
} else {
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_04(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 1
}
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.gmA, -, v_sip);
//Rx/Gx exchange after INVITE (SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_03(vc_vxlte_monitor_components.rx);// Event 2
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 3
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 4
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 5
f_mtc_check_TP_RX_PCSCF_RAA_01(vc_vxlte_monitor_components.rx);// Events 7,8
//f_mtc_check_TP_GX_PCRF_CCA_01(vc_vxlte_monitor_components.gx); // Events 6,9
f_mtc_check_TP_MW_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 10
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_INVITE_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 11
f_mtc_check_TP_MX_ECSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwEB, -, v_sip);
f_mtc_check_TP_IC_IBCF_INVITE_01(vc_vxlte_monitor_components.ic, true); // INVITE Event 12 (NOTE: comment out if ISC simulated by Ic)
f_mtc_check_TP_IC_IBCF_INVITE_02(vc_vxlte_monitor_components.ic, true); // INVITE Event 12 (NOTE: comment out if ISC simulated by Ic)
f_mtc_check_TP_IC_IBCF_INVITE_03(vc_vxlte_monitor_components.ic); // INVITE ENUM Event 8
// 183 Session Progress
f_mtc_check_TP_IC_IBCF_183RESP_01(vc_vxlte_monitor_components.ic, -); // 183 Event 13
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 14
f_mtc_check_TP_MW_PCSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 15
f_mtc_check_TP_GM_PCSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 20
//Rx/Gx exchange after 183(SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_04(vc_vxlte_monitor_components.rx);// Event 16
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 17
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 18
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 19
f_mtc_check_TP_IC_IBCF_180RESP_01(vc_vxlte_monitor_components.ic); // 180 Ringing – Event 22
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 23
f_mtc_check_TP_MW_PCSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 24
f_mtc_check_TP_GM_PCSCF_180RINGING_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 25
f_mtc_userCheckRinging(v_psap);
f_mtc_userCheckPeerIsRinging(v_ueA);
f_mtc_userAnswerCall(v_psap);
f_mtc_check_TP_IC_IBCF_2XXRESP_01(vc_vxlte_monitor_components.ic, true); // 200 OK – Event 26
f_mtc_check_TP_IC_IBCF_2XXRESP_02(vc_vxlte_monitor_components.ic, true); // 200 OK – Event 26
f_mtc_check_TP_IC_IBCF_2XXRESP_03(vc_vxlte_monitor_components.ic); // 200 OK – Event 26
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 27
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 28
f_mtc_check_TP_GM_PCSCF_200OK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 29
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 30
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 31
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 32
f_mtc_check_TP_IC_IBCF_ACK_01(vc_vxlte_monitor_components.ic); // ACK – Event 33
f_mtc_userCheckCallEstablished(v_ueA); // Event 34
f_mtc_userCheckCallEstablished(v_psap); // Event 34
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_INI_05
group f_TD_VoLTE_ECO_INT_INI_05 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_05() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_05
} // End of f_TD_VoLTE_ECO_INT_INI_05
* @desc To demonstrate the establishment of dedicated bearers at the originating EPC due to SIP emergency session establishment within an emergency registration.
* PSAP is located in the IM CN subsystem of another network vonnected via IBCF. The PSAP URI is delivered by the LRF.
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5.3.1.7 UE calling PSAP in other network via IBCF, LRF derived PSAP URI
* @remark This is option2: IBCF is connected to the PSAP, the interface IBCF and the PSAP is the Mm interface
*/
testcase TD_VoLTE_ECO_INT_INI_06() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_IC_INTERFACENAME, // IBCF -> IMS_B -> PSAP
PX_SIP_ML_E_LRF_INTERFACENAME // E-CSCF -> LRF: mlE_LRF
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_06();
// Test body
//f_mtc_userInitiateCall (v_ueA, v_userTelInfoB);
Yann Garcia
committed
if (not(PX_ECALL)) {
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 1
} else {
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_04(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 1
}
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.gmA, -, v_sip);
//Rx/Gx exchange after INVITE (SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_03(vc_vxlte_monitor_components.rx);// Event 2
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 3
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 4
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 5
f_mtc_check_TP_RX_PCSCF_RAA_01(vc_vxlte_monitor_components.rx);// Events 7,8
//f_mtc_check_TP_GX_PCRF_CCA_01(vc_vxlte_monitor_components.gx); // Events 6,9
f_mtc_check_TP_MW_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 10
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
// FIXME f_mtc_check_TP_MW_IBCF_xxx <--> f_mtc_check_TP_ML_EBCF_xxx
Yann Garcia
committed
f_mtc_check_TP_ML_ECSCF_ECO_INVITE_01(vc_vxlte_monitor_components.mlE_LRF, -, v_sip); // Event 11
f_mtc_check_TP_MX_LRF_3xxAny_01(vc_vxlte_monitor_components.mlE_LRF, -, v_sip); // Event 12
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_INVITE_02(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 13
f_mtc_check_TP_MX_ECSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwEB, -, v_sip);
f_mtc_check_TP_IC_IBCF_INVITE_01(vc_vxlte_monitor_components.ic, true); // INVITE Event 14
f_mtc_check_TP_IC_IBCF_INVITE_02(vc_vxlte_monitor_components.ic, true); // INVITE Event 14
f_mtc_check_TP_IC_IBCF_183RESP_01(vc_vxlte_monitor_components.ic,-); // 183 Event 15
// 183 Session Progress
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 16
f_mtc_check_TP_MW_PCSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 17
f_mtc_check_TP_GM_PCSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 24
//Rx/Gx exchange after 183(SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_04(vc_vxlte_monitor_components.rx);// Event 18
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 19
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 20
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 21
f_mtc_check_TP_IC_IBCF_180RESP_01(vc_vxlte_monitor_components.ic, true); // 180 Ringing – Event 24
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 25
f_mtc_check_TP_MW_PCSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 26
f_mtc_check_TP_GM_PCSCF_180RINGING_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 27
f_mtc_userCheckRinging(v_psap);
f_mtc_userCheckPeerIsRinging(v_ueA);
f_mtc_userAnswerCall(v_psap);
f_mtc_check_TP_IC_IBCF_2XXRESP_01(vc_vxlte_monitor_components.ic, true); // 200 OK – Event 28
f_mtc_check_TP_IC_IBCF_2XXRESP_02(vc_vxlte_monitor_components.ic, true); // 200 OK – Event 28
f_mtc_check_TP_IC_IBCF_2XXRESP_03(vc_vxlte_monitor_components.ic); // 200 OK – Event 28
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 29
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 30
f_mtc_check_TP_GM_PCSCF_200OK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 31
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 32
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 33
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 34
f_mtc_check_TP_IC_IBCF_ACK_01(vc_vxlte_monitor_components.ic); // ACK – Event 35
f_mtc_userCheckCallEstablished(v_ueA); // Event 36
f_mtc_userCheckCallEstablished(v_psap); // Event 36
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_INI_06
group f_TD_VoLTE_ECO_INT_INI_06 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_06() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_06
} // End of group f_TD_VoLTE_ECO_INT_INI_06
/**
* @desc To demonstrate the establishment of dedicated bearers at the originating EPC due to SIP emergency session establishment within an emergency registration.
* PSAP is located in the PSTN connected via BGCF.
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5.3.1.8 UE calling PSAP in PSTN via BGCF
*/
testcase TD_VoLTE_ECO_INT_INI_07() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_MW_EB_INTERFACENAME, // E-CSCF -> IBCF
PX_SIP_IC_INTERFACENAME // IBCF -> IMS -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_07();
// Test body
Yann Garcia
committed
if (not(PX_ECALL)) {
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 1
} else {
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_04(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 1
}
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.gmA, -, v_sip);
//Rx/Gx exchange after INVITE (SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_03(vc_vxlte_monitor_components.rx);// Event 2
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 3
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 4
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 5
f_mtc_check_TP_RX_PCSCF_RAA_01(vc_vxlte_monitor_components.rx);// Events 7,8
//f_mtc_check_TP_GX_PCRF_CCA_01(vc_vxlte_monitor_components.gx); // Events 6,9
f_mtc_check_TP_MW_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 10
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
Yann Garcia
committed
f_mtc_check_TP_MI_ECSCF_ECO_INVITE_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 11
f_mtc_check_TP_MI_ECSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwEB, -, v_sip);
f_mtc_check_TP_MM_ECSCF_ECO_INVITE_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 12
f_mtc_check_TP_MM_ECSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 13
Yann Garcia
committed
f_mtc_check_TP_MI_ECSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 14
f_mtc_check_TP_MW_PCSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 15
f_mtc_check_TP_GM_PCSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 20
//Rx/Gx exchange after 183(SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_04(vc_vxlte_monitor_components.rx);// Event 16
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 17
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 18
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 19
f_mtc_check_TP_MM_ECSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 180 Ringing – Event 22
Yann Garcia
committed
f_mtc_check_TP_MI_ECSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 23
f_mtc_check_TP_MW_PCSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 24
f_mtc_check_TP_GM_PCSCF_180RINGING_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 25
f_mtc_userCheckRinging(v_psap);
f_mtc_userCheckPeerIsRinging(v_ueA);
f_mtc_userAnswerCall(v_psap);
f_mtc_check_TP_MM_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 200 OK – Event 26
Yann Garcia
committed
f_mtc_check_TP_MI_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 27
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 28
f_mtc_check_TP_GM_PCSCF_200OK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 29
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 30
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 31
Yann Garcia
committed
f_mtc_check_TP_MI_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 32
f_mtc_check_TP_MM_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // ACK – Event 33
f_mtc_userCheckCallEstablished(v_ueA); // Event 34
f_mtc_userCheckCallEstablished(v_psap); // Event 34
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_INI_07
group f_TD_VoLTE_ECO_INT_INI_07 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_07() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_07
} // End of group f_TD_VoLTE_ECO_INT_INI_07
/**
* @desc To demonstrate the establishment of dedicated bearers at the originating EPC due to SIP emergency session establishment within an emergency registration.
* PSAP is located in the PSTN connected via BGCF. The PSAP URI is delivered by the LRF
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5.3.1.9 UE calling PSAP in PSTN via BGCF, LRF derived PSAP URI
*/
testcase TD_VoLTE_ECO_INT_INI_08() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_ML_E_LRF_INTERFACENAME // E-CSCF -> LRF: mlE_LRF
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_08();
// Test body
Yann Garcia
committed
if (not(PX_ECALL)) {
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 1
} else {
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_04(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 1
}
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.gmA, -, v_sip);
//Rx/Gx exchange after INVITE (SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_03(vc_vxlte_monitor_components.rx);// Event 2
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 3
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 4
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 5
f_mtc_check_TP_RX_PCSCF_RAA_01(vc_vxlte_monitor_components.rx);// Events 7,8
//f_mtc_check_TP_GX_PCRF_CCA_01(vc_vxlte_monitor_components.gx); // Events 6,9
f_mtc_check_TP_MW_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 10
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
// FIXME f_mtc_check_TP_MW_IBCF_xxx <--> f_mtc_check_TP_ML_EBCF_xxx
Yann Garcia
committed
f_mtc_check_TP_ML_ECSCF_ECO_INVITE_01(vc_vxlte_monitor_components.mlE_LRF, -, v_sip); // Event 11
f_mtc_check_TP_MX_LRF_3xxAny_01(vc_vxlte_monitor_components.mlE_LRF, -, v_sip); // Event 12
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_INVITE_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 13
f_mtc_check_TP_MX_ECSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwEB, -, v_sip);
f_mtc_check_TP_IC_IBCF_INVITE_01(vc_vxlte_monitor_components.ic, true); // INVITE Event 14
f_mtc_check_TP_IC_IBCF_INVITE_02(vc_vxlte_monitor_components.ic, true); // INVITE Event 14
f_mtc_check_TP_IC_IBCF_183RESP_01(vc_vxlte_monitor_components.ic,-); // 183 Event 15
// 183 Session Progress
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 16
f_mtc_check_TP_MW_PCSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 17
f_mtc_check_TP_GM_PCSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 24
//Rx/Gx exchange after 183(SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_04(vc_vxlte_monitor_components.rx);// Event 18
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 19
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 20
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 21
f_mtc_check_TP_IC_IBCF_180RESP_01(vc_vxlte_monitor_components.ic, true); // 180 Ringing – Event 24
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 25
f_mtc_check_TP_MW_PCSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 26
f_mtc_check_TP_GM_PCSCF_180RINGING_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 27
f_mtc_userCheckRinging(v_psap);
f_mtc_userCheckPeerIsRinging(v_ueA);
f_mtc_userAnswerCall(v_psap);
f_mtc_check_TP_IC_IBCF_2XXRESP_01(vc_vxlte_monitor_components.ic, true); // 200 OK – Event 28
f_mtc_check_TP_IC_IBCF_2XXRESP_02(vc_vxlte_monitor_components.ic, true); // 200 OK – Event 28
f_mtc_check_TP_IC_IBCF_2XXRESP_03(vc_vxlte_monitor_components.ic); // 200 OK – Event 28
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 29
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 30
f_mtc_check_TP_GM_PCSCF_200OK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 31
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 32
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 33
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 34
f_mtc_check_TP_IC_IBCF_ACK_01(vc_vxlte_monitor_components.ic); // ACK – Event 35
f_mtc_userCheckCallEstablished(v_ueA); // Event 36
f_mtc_userCheckCallEstablished(v_psap); // Event 36
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_INI_08
group f_TD_VoLTE_ECO_INT_INI_08 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_08() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_08
} // End of group f_TD_VoLTE_ECO_INT_INI_08
/**
* @desc To demonstrate the establishment of dedicated bearers at the originating EPC due to SIP emergency session establishment over AS with non-emergency registration.
* PSAP is located in the IM CN subsystem of IMS A.
*
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5.3.1.10 UE calling PSAP over AS with non-emergency registration
*/
testcase TD_VoLTE_ECO_INT_INI_09() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_MM_B_PSAP_INTERFACENAME,
PX_SIP_ISC_INTERFACENAME
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_09_01();
// Test body
//f_mtc_userInitiateCall (v_ueA, v_infoPsap);
action("UE A needs to trigger an emergency call"); // Event 1
f_mtc_check_TP_ISC_SCSCF_ECO_INVITE_01(vc_vxlte_monitor_components.isc, -, v_sip); // INVITE Event 2
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.isc, -, v_sip);
f_mtc_check_TP_MW_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.mwIE, -, v_sip); // Event 3
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwIE, -, v_sip);
f_mtc_check_TP_MM_ECSCF_ECO_INVITE_01(vc_vxlte_monitor_components.mwS_PSAP, -, v_sip); // Event 4
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwS_PSAP, -, v_sip);
// 183 Session Progress
f_mtc_check_TP_MM_ECSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwS_PSAP, -, v_sip); // Event 5
f_mtc_check_TP_MI_ECSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwIE, -, v_sip); // Event 6
f_mtc_check_TP_ISC_SCSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.isc, -, v_sip); // Event 7
// 180 Ringing
f_mtc_check_TP_IC_IBCF_180RESP_01(vc_vxlte_monitor_components.mwS_PSAP, true); // 180 Ringing – Event 10
f_mtc_check_TP_MX_ECSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwIE, -, v_sip); // Event 11
f_mtc_check_TP_ISC_SCSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.isc, -, v_sip); // Event 12
f_mtc_userCheckRinging(v_psap);
f_mtc_userCheckPeerIsRinging(v_ueA);
f_mtc_userAnswerCall(v_psap);
// 200 OK
f_mtc_check_TP_MM_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwS_PSAP, -, v_sip); // Event 14
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwIE, -, v_sip); // Event 15
f_mtc_check_TP_ISC_SCSCF_ECO_200OK_01(vc_vxlte_monitor_components.isc, -, v_sip); // Event 16
f_mtc_check_TP_ISC_SCSCF_ECO_ACK_01(vc_vxlte_monitor_components.isc, -, v_sip); // Event 19
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwIE, -, v_sip); // Event 20
f_mtc_check_TP_MX_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwS_PSAP, -, v_sip); // Event 21
f_mtc_userCheckCallEstablished(v_ueA); // Event 22
f_mtc_userCheckCallEstablished(v_psap); // Event 22
1403
1404
1405
1406
1407
1408
1409
1410
1411
1412
1413
1414
1415
1416
1417
1418
1419
1420
1421
1422
1423
1424
1425
1426
1427
1428
1429
1430
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_INI_09
group f_TD_VoLTE_ECO_INT_INI_09 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_09_01() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_09
} // End of group f_TD_VoLTE_ECO_INT_INI_09
/**
* @desc To demonstrate that if an emergency call has been terminated, the attempt by the PSAP call taker to communicate back to the emergency caller shall be answered.
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5.3.1.11 Callback from PSAP
*/
testcase TD_VoLTE_ECO_INT_INI_10_01() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_userRegistration(v_ueA, v_userInfoA);
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_userInitiateCall (v_ueA, v_infoPsap); // Event 1
f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_10_01();
// Test body
Yann Garcia
committed
f_mtc_check_TP_MM_ECSCF_ECO_INVITE_03(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // INVITE Event 1
f_mtc_check_TP_MM_ECSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip);
f_mtc_check_TP_MW_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 6
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 7
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.gmA, -, v_sip);
// 183 Session Progress
f_mtc_check_TP_GM_PCSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 8
f_mtc_check_TP_MW_PCSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 9
f_mtc_check_TP_MM_ECSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 183 In Progress Event 10
f_mtc_check_TP_GM_PCSCF_180RINGING_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 16
f_mtc_check_TP_MW_PCSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 17
f_mtc_check_TP_MM_ECSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 180 Ringing – Event 20
f_mtc_userCheckRinging(v_ueA); // Event 15
f_mtc_userCheckPeerIsRinging(v_psap); // Event 15
f_mtc_userAnswerCall(v_ueA); // Event 26
f_mtc_check_TP_GM_PCSCF_200OK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 18
Yann Garcia
committed
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 19
f_mtc_check_TP_MM_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 200 OK Event 21
f_mtc_check_TP_MM_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // ACK – Event 22
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 35
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // ACK Event 36
f_mtc_userCheckCallEstablished(v_ueA); // Event 37
f_mtc_userCheckCallEstablished(v_psap); // Event 37
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_INI_10_01
group f_TD_VoLTE_ECO_INT_INI_10_01 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_10_01() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_10_01
} // End of group f_TD_VoLTE_ECO_INT_INI_10_01
/**
* @desc To demonstrate that if an emergency call has been terminated, the attempt by the PSAP call taker to communicate back to the emergency caller shall be answered.
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5.3.1.11 Callback from PSAP
*/
testcase TD_VoLTE_ECO_INT_INI_10_02() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_IC_INTERFACENAME // IBCF -> IMS_B -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_10_02();
// Test body
//f_mtc_userInitiateCall (v_ueA, v_userTelInfoB);
Yann Garcia
committed
f_mtc_check_TP_IC_IBCF_INVITE_01(vc_vxlte_monitor_components.ic); // Event 2
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.ic, -, v_sip);
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_INVITE_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 3
f_mtc_check_TP_MX_ECSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwEB, -, v_sip);
f_mtc_check_TP_MW_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 6
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
f_mtc_check_TP_GM_PCSCF_INVITE_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 7
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.gmA, -, v_sip);
// 183 Session Progress
f_mtc_check_TP_GM_PCSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 8
f_mtc_check_TP_MW_PCSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 9
f_mtc_check_TP_MM_ECSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 183 In Progress Event 10
f_mtc_check_TP_GM_PCSCF_180RINGING_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 16
f_mtc_check_TP_MW_PCSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 17
f_mtc_check_TP_MM_ECSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 180 Ringing – Event 20
f_mtc_userCheckRinging(v_ueA); // Event 15
f_mtc_userCheckPeerIsRinging(v_psap); // Event 15
f_mtc_userAnswerCall(v_ueA); // Event 26
f_mtc_check_TP_GM_PCSCF_200OK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 18
Yann Garcia
committed
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 19
f_mtc_check_TP_MM_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 200 OK Event 21
f_mtc_check_TP_MM_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // ACK – Event 22
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 35
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // ACK Event 36
f_mtc_userCheckCallEstablished(v_ueA); // Event 37
f_mtc_userCheckCallEstablished(v_psap); // Event 37
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_INI_10_02
group f_TD_VoLTE_ECO_INT_INI_10_02 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_10_02() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_10_02
} // End of group f_TD_VoLTE_ECO_INT_INI_10_02
/**
* @desc To demonstrate that if an emergency call has been terminated, the attempt by the PSAP call taker to communicate back to the emergency caller shall be answered.
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5.3.1.11 Callback from PSAP
*/
testcase TD_VoLTE_ECO_INT_INI_10_03() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_10_03();
// Test body
Yann Garcia
committed
f_mtc_check_TP_IC_IBCF_INVITE_02(vc_vxlte_monitor_components.ic); // Event 4
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_INVITE_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 5
f_mtc_check_TP_MX_ECSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwEB, -, v_sip);
Yann Garcia
committed
1680
1681
1682
1683
1684
1685
1686
1687
1688
1689
1690
1691
1692
1693
1694
1695
1696
1697
1698
1699
1700
1701
1702
1703
1704
1705
1706
1707
1708
1709
1710
1711
1712
1713
1714
1715
1716
f_mtc_check_TP_MW_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 6
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
f_mtc_check_TP_GM_PCSCF_INVITE_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 7
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.gmA, -, v_sip);
// 183 Session Progress
f_mtc_check_TP_GM_PCSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 8
f_mtc_check_TP_MW_PCSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 9
f_mtc_check_TP_MW_PCSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 13
f_mtc_check_TP_IC_IBCF_183RESP_01(vc_vxlte_monitor_components.ic); // Event 14
f_mtc_userCheckRinging(v_ueA); // Event 15
f_mtc_userCheckPeerIsRinging(v_psap); // Event 15
f_mtc_check_TP_GM_PCSCF_180RINGING_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 16
f_mtc_check_TP_MW_PCSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 17
f_mtc_check_TP_GM_PCSCF_200OK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 18
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 19
f_mtc_check_TP_MW_PCSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 29
f_mtc_check_TP_IC_IBCF_180RESP_01(vc_vxlte_monitor_components.ic); // Event 30
f_mtc_check_TP_MW_PCSCF_200OK_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 31
f_mtc_check_TP_IC_IBCF_2XXRESP_01(vc_vxlte_monitor_components.ic); // Event 32
f_mtc_check_TP_IC_IBCF_ACK_01(vc_vxlte_monitor_components.ic); // Event 33
f_mtc_check_TP_MW_PCSCF_ACK_02(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 34
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 35
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // ACK Event 36
f_mtc_userCheckCallEstablished(v_ueA); // Event 37
f_mtc_userCheckCallEstablished(v_psap); // Event 37
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_INI_10_03
group f_TD_VoLTE_ECO_INT_INI_10_03 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_10_03() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_10_03
} // End of group f_TD_VoLTE_ECO_INT_INI_10_03
} // End of group EmergencySessionEstablishment
group EmergencySessionRelease {
/**
* @desc To perform originating UE session release and the tear down of related dedicated bearers.
* @see ETSI TS 103 795-2 Clause 5.3.2.1 UE Initiated Emergency Session Release
* @remark This is option 1: PSAP is in IMS A network
*/
Yann Garcia
committed
testcase TD_VoLTE_EMC_INT_REL_01_01() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
Yann Garcia
committed
f_mtc_check_precond_TD_VoLTE_EMC_INT_REL_01_01();
// Test body
f_mtc_check_TP_GM_PCSCF_ECO_BYE_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 2
f_mtc_check_TP_MW_PCSCF_ECO_BYE_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 3
f_mtc_check_TP_MM_ECSCF_ECO_BYE_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 4
//Rx/Gx exchange after BYE was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_STR_01(vc_vxlte_monitor_components.rx); // (STR – Event 10
f_mtc_check_TP_GX_PCRF_RAR_02(vc_vxlte_monitor_components.gx, true); // (RAR – Event 11)
f_mtc_check_TP_GX_PGW_RAA_03(vc_vxlte_monitor_components.gx); // (RAA – Event 12)
f_mtc_check_TP_RX_PCRF_STA_01(vc_vxlte_monitor_components.rx); // (STA – Event 13)
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 13
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 18
f_mtc_check_TP_GM_PCSCF_200OK_02(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 19
f_mtc_userCheckCallTerminated(v_ueA); // Event 20
f_mtc_userCheckCallCancelled(v_psap); // Event 21
// Postamble
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
Yann Garcia
committed
} // End of TC TD_VoLTE_EMC_INT_REL_01_01
Yann Garcia
committed
group f_TD_VoLTE_EMC_INT_REL_01_01 {
Yann Garcia
committed
function f_mtc_check_precond_TD_VoLTE_EMC_INT_REL_01_01() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
Yann Garcia
committed
} // End of function f_mtc_check_precond_TD_VoLTE_EMC_INT_REL_01_01
Yann Garcia
committed
} // End of group f_TD_VoLTE_EMC_INT_REL_01_01
/**
* @desc To perform originating UE session release and the tear down of related dedicated bearers.
* @see ETSI TS 103 795-2 Clause 5.3.2.1 UE Initiated Emergency Session Release
* @remark This is option 2: PSAP is not in IMS A network
*/
Yann Garcia
committed
testcase TD_VoLTE_EMC_INT_REL_01_02 ( ) runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_IC_INTERFACENAME // IBCF -> IMS_B -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
Yann Garcia
committed
f_mtc_check_precond_TD_VoLTE_EMC_INT_REL_01_02();
// Test body
f_mtc_check_TP_GM_PCSCF_ECO_BYE_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 2
f_mtc_check_TP_MW_PCSCF_ECO_BYE_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 3
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_BYE_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 5
f_mtc_check_TP_IC_IBCF_ECO_BYE_01(vc_vxlte_monitor_components.ic); // Event 6
//Rx/Gx exchange after BYE was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_STR_01(vc_vxlte_monitor_components.rx); // (STR – Event 10
f_mtc_check_TP_GX_PCRF_RAR_02(vc_vxlte_monitor_components.gx, true); // (RAR – Event 11)
f_mtc_check_TP_GX_PGW_RAA_03(vc_vxlte_monitor_components.gx); // (RAA – Event 12)
f_mtc_check_TP_RX_PCRF_STA_01(vc_vxlte_monitor_components.rx); // (STA – Event 13)
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 15
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 18
f_mtc_check_TP_GM_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 19
f_mtc_userCheckCallTerminated(v_ueA); // Event 22
f_mtc_userCheckCallCancelled(v_psap); // Event 23
// Postamble
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
Yann Garcia
committed
} // End of TC f_TD_VoLTE_EMC_INT_REL_01_01
Yann Garcia
committed
group f_TD_VoLTE_EMC_INT_REL_01_02 {
Yann Garcia
committed
function f_mtc_check_precond_TD_VoLTE_EMC_INT_REL_01_02() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
Yann Garcia
committed
} // End of function f_mtc_check_precond_TD_VoLTE_EMC_INT_REL_01_02
Yann Garcia
committed
} // End of f_TD_VoLTE_EMC_INT_REL_01_02
/**
* @desc To perform originating UE session release and the tear down of related dedicated bearers.
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5.3.3.1 UE Initiated Emergency Session Release
* @remark This is option 3: PSAP is in PSTN network
*/
Yann Garcia
committed
testcase TD_VoLTE_EMC_INT_REL_01_03() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME, // E-CSCF -> IBCF
PX_SIP_IC_INTERFACENAME // IBCF -> IMS -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_userInitiateCall (v_ueA, v_infoPsap); // Event 1
Yann Garcia
committed
f_mtc_check_precond_TD_VoLTE_EMC_INT_REL_01_03();
// Test body
f_mtc_check_TP_GM_PCSCF_ECO_BYE_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 2
f_mtc_check_TP_MW_PCSCF_ECO_BYE_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 3
Yann Garcia
committed
f_mtc_check_TP_MI_ECSCF_ECO_BYE_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 7
//Rx/Gx exchange after BYE was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_STR_01(vc_vxlte_monitor_components.rx); // (STR – Event 10
f_mtc_check_TP_GX_PCRF_RAR_02(vc_vxlte_monitor_components.gx, true); // (RAR – Event 11)
f_mtc_check_TP_GX_PGW_RAA_03(vc_vxlte_monitor_components.gx); // (RAA – Event 12)
f_mtc_check_TP_RX_PCRF_STA_01(vc_vxlte_monitor_components.rx); // (STA – Event 13)
Yann Garcia
committed
f_mtc_check_TP_MI_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 17
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 20
f_mtc_check_TP_GM_PCSCF_200OK_02(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 21
f_mtc_userCheckCallTerminated(v_ueA); // Event 22
f_mtc_userCheckCallCancelled(v_psap); // Event 23
// Postamble
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
Yann Garcia
committed
} // End of TC TD_VoLTE_EMC_INT_REL_01_03
Yann Garcia
committed
group f_TD_VoLTE_EMC_INT_REL_01_03 {
Yann Garcia
committed
function f_mtc_check_precond_TD_VoLTE_EMC_INT_REL_01_03() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
Yann Garcia
committed
} // End of function f_mtc_check_precond_TD_VoLTE_EMC_INT_REL_01_03
Yann Garcia
committed
} // End of group f_TD_VoLTE_EMC_INT_REL_01_03
/**
* @desc To perform originating PSAP session release and the tear down of related dedicated bearers.
* @see ETSI TS 103 795-2 Clause 5.3.2.2 PSAP Initiated Emergency Session Release
* @remark This is option 1: PSAP is in IMS A network
*/
testcase TD_VoLTE_ECO_INT_REL_02_01() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_MW_EB_INTERFACENAME, // E-CSCF -> IBCF
PX_SIP_MM_B_PSAP_INTERFACENAME // E-CSCCF -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TD_VoLTE_ECO_INT_REL_02_01();
// Test body
Yann Garcia
committed
f_mtc_check_TP_MM_ECSCF_ECO_BYE_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 1
f_mtc_check_TP_MW_PCSCF_ECO_BYE_02(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 7
f_mtc_check_TP_GM_PCSCF_ECO_BYE_02(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 8
//Rx/Gx exchange after BYE was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_STR_01(vc_vxlte_monitor_components.rx); // Event 9
f_mtc_check_TP_GX_PCRF_RAR_02(vc_vxlte_monitor_components.gx, true); // Event 10
f_mtc_check_TP_GX_PGW_RAA_03(vc_vxlte_monitor_components.gx); // Event 1
f_mtc_check_TP_RX_PCRF_STA_01(vc_vxlte_monitor_components.rx); // Event 12
f_mtc_check_TP_GM_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 13
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 14
f_mtc_check_TP_MM_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 15
f_mtc_userCheckCallTerminated(v_ueA); // Event 21
f_mtc_userCheckCallCancelled(v_psap); // Event 20
// Postamble
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_REL_02_01
group f_TD_VoLTE_ECO_INT_REL_02_01 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_REL_02_01() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_REL_02_01
} // End of group f_TD_VoLTE_ECO_INT_REL_02_01
/**
* @desc To perform originating PSAP session release and the tear down of related dedicated bearers.
* @see ETSI TS 103 795-2 Clause 5.3.2.2 PSAP Initiated Emergency Session Release
* @remark This is option2: PSAP is not in IMS A network
*/
testcase TD_VoLTE_ECO_INT_REL_02_02() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_IC_INTERFACENAME // IBCF -> IMS
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TD_VoLTE_ECO_INT_REL_02_02();
// Test body
Yann Garcia
committed
f_mtc_check_TP_IC_IBCF_BYE_01(vc_vxlte_monitor_components.ic); // Event 3
f_mtc_check_TP_MM_ECSCF_ECO_BYE_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 4
f_mtc_check_TP_MW_PCSCF_ECO_BYE_02(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 7
f_mtc_check_TP_GM_PCSCF_ECO_BYE_02(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 8
//Rx/Gx exchange after BYE was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_STR_01(vc_vxlte_monitor_components.rx); // Event 9
f_mtc_check_TP_GX_PCRF_RAR_02(vc_vxlte_monitor_components.gx, true); // Event 10
f_mtc_check_TP_GX_PGW_RAA_03(vc_vxlte_monitor_components.gx); // Event 1
f_mtc_check_TP_RX_PCRF_STA_01(vc_vxlte_monitor_components.rx); // Event 12
f_mtc_check_TP_GM_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 13
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 14
f_mtc_check_TP_MM_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 16
f_mtc_check_TP_IC_IBCF_2XXRESP_01(vc_vxlte_monitor_components.ic); // Event 17
f_mtc_userCheckCallTerminated(v_ueA); // Event 21
f_mtc_userCheckCallCancelled(v_psap); // Event 20
// Postamble
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_REL_02_02
group f_TD_VoLTE_ECO_INT_REL_02_02 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_REL_02_02() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_REL_02_02
} // End of group f_TD_VoLTE_ECO_INT_REL_02_02
/**
* @desc To perform originating PSAP session release and the tear down of related dedicated bearers.
* On call release initiated bye PSAP, the P-CSCF A should trigger the removal of all relevant previously created bearers
* @see ETSI TS 103 795-2 Clause 5.3.2.2 PSAP Initiated Emergency Session Release
* @remark This is option3: PSAP is in PSTN network
*/
testcase TD_VoLTE_ECO_INT_REL_02_03() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TD_VoLTE_ECO_INT_REL_02_03();
// Test body
action("PSAP Initiated Emergency Session Release via PSTN"); // Event 5
f_mtc_check_TP_MX_ECSCF_ECO_BYE_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 6
Yann Garcia
committed
f_mtc_check_TP_MW_PCSCF_ECO_BYE_02(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 7
f_mtc_check_TP_GM_PCSCF_ECO_BYE_02(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 8
//Rx/Gx exchange after BYE was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_STR_01(vc_vxlte_monitor_components.rx); // Event 9
f_mtc_check_TP_GX_PCRF_RAR_02(vc_vxlte_monitor_components.gx, true); // Event 10
f_mtc_check_TP_GX_PGW_RAA_03(vc_vxlte_monitor_components.gx); // Event 1
f_mtc_check_TP_RX_PCRF_STA_01(vc_vxlte_monitor_components.rx); // Event 12
f_mtc_check_TP_GM_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 13
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 14
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 18
f_mtc_check_TP_IC_IBCF_2XXRESP_01(vc_vxlte_monitor_components.ic); // Event 19
f_mtc_userCheckCallTerminated(v_ueA); // Event 21
f_mtc_userCheckCallCancelled(v_psap); // Event 20
// Postamble
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_REL_02_03
group f_TD_VoLTE_ECO_INT_REL_02_03 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_REL_02_03() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_REL_02_03
} // End of group f_TD_VoLTE_ECO_INT_REL_02_03
} // End of group EmergencySessionRelease
/**
* @see ETSI TS 103 795-2 Clause 5.3.3 Emergency Session Abort/Reject
*/
group EmergencySessionAbortOrReject {
/**
* @desc To perform SIP session abort (originating side) and the related interactions with PCRF A and EPC A.
* @see ETSI TS 103 795-2 Clause 5.3.3.1 Emergency Session Abort
* @remark This is option 1: PSAP is in IMS A network
*/
Yann Garcia
committed
testcase TD_VoLTE_EMC_INT_ABT_01_01() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_MW_EB_INTERFACENAME, // E-CSCF -> IBCF
PX_SIP_MM_B_PSAP_INTERFACENAME // E-CSCCF -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
Yann Garcia
committed
f_mtc_check_precond_TD_VoLTE_EMC_INT_ABT_01_01();
// Test body
//f_mtc_userInitiateCall (v_ueA, v_userTelInfoB);
Yann Garcia
committed
f_mtc_check_TP_GM_PCSCF_EMC_CANCEL_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 1
//Rx/Gx exchange after CANCEL was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_STR_01(vc_vxlte_monitor_components.rx); // (STR – Event 2
f_mtc_check_TP_GX_PCRF_RAR_02(vc_vxlte_monitor_components.gx, true); // (RAR – Event 3)
f_mtc_check_TP_GX_PGW_RAA_03(vc_vxlte_monitor_components.gx); // (RAA – Event 4)
f_mtc_check_TP_RX_PCRF_STA_01(vc_vxlte_monitor_components.rx); // (STA – Event 5)
Yann Garcia
committed
f_mtc_check_TP_MW_PCSCF_EMC_CANCEL_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 6
Yann Garcia
committed
f_mtc_check_TP_MM_ECSCF_EMC_CANCEL_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 7
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 8
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 17
f_mtc_check_TP_GM_PCSCF_200OK_02(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 18
Yann Garcia
committed
f_mtc_check_TP_MW_PCSCF_EMC_487INVITE_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 24
f_mtc_check_TP_GM_PCSCF_487INVITE_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 25
f_mtc_check_TP_GM_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 26
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 27
f_mtc_check_TP_MM_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 28
f_mtc_userCheckCallTerminated(v_ueA); // Event 33
f_mtc_userCheckCallCancelled(v_psap); // Event 34
// Postamble
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
Yann Garcia
committed
} // End of TC TD_VoLTE_EMC_INT_ABT_01_01
Yann Garcia
committed
group f_TD_VoLTE_EMC_INT_ABT_01_01 {
Yann Garcia
committed
function f_mtc_check_precond_TD_VoLTE_EMC_INT_ABT_01_01() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
Yann Garcia
committed
} // End of function f_mtc_check_precond_TD_VoLTE_EMC_INT_ABT_01_01
Yann Garcia
committed
} // End of group f_TD_VoLTE_EMC_INT_ABT_01_01
/**
* @desc To perform SIP session abort (originating side) and the related interactions with PCRF A and EPC A.
* @see ETSI TS 103 795-2 Clause 5.3.3.1 Emergency Session Abort
* @remark This is option 2: PSAP is not in IMS A network
*/
Yann Garcia
committed
testcase TD_VoLTE_EMC_INT_ABT_01_02() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_IC_INTERFACENAME // IBCF -> IMS -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
Yann Garcia
committed
f_mtc_check_precond_TD_VoLTE_EMC_INT_ABT_01_02();
// Test body
//f_mtc_userInitiateCall (v_ueA, v_userTelInfoB);
Yann Garcia
committed
f_mtc_check_TP_GM_PCSCF_EMC_CANCEL_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 1
//Rx/Gx exchange after CANCEL was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_STR_01(vc_vxlte_monitor_components.rx); // (STR – Event 2
f_mtc_check_TP_GX_PCRF_RAR_02(vc_vxlte_monitor_components.gx, true); // (RAR – Event 3)
f_mtc_check_TP_GX_PGW_RAA_03(vc_vxlte_monitor_components.gx); // (RAA – Event 4)
f_mtc_check_TP_RX_PCRF_STA_01(vc_vxlte_monitor_components.rx); // (STA – Event 5)
Yann Garcia
committed
f_mtc_check_TP_MW_PCSCF_EMC_CANCEL_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 6
Yann Garcia
committed
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_EMC_CANCEL_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 9
Yann Garcia
committed
f_mtc_check_TP_IC_IBCF_CANCEL_01(vc_vxlte_monitor_components.ic, true); // CANCEL Event 10 (NOTE: comment out if ISC simulated by Ic)
f_mtc_check_TP_IC_IBCF_2XXRESP_01(vc_vxlte_monitor_components.ic); // 200 CANCEL – Event 11
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 12
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 17
f_mtc_check_TP_GM_PCSCF_200OK_02(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 18
f_mtc_check_TP_IC_IBCF_487INVITE_01(vc_vxlte_monitor_components.ic); // Event 20
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_EMC_487INVITE_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 21
Yann Garcia
committed
f_mtc_check_TP_MW_PCSCF_EMC_487INVITE_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 24
f_mtc_check_TP_GM_PCSCF_487INVITE_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 25
f_mtc_check_TP_GM_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 26
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 27
Yann Garcia
committed
f_mtc_check_TP_MX_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 29
f_mtc_check_TP_IC_IBCF_ACK_01(vc_vxlte_monitor_components.ic, true); // Event 30
f_mtc_userCheckCallTerminated(v_ueA); // Event 33
f_mtc_userCheckCallCancelled(v_psap); // Event 34
// Postamble
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
Yann Garcia
committed
} // End of TC TD_VoLTE_EMC_INT_ABT_01_02
Yann Garcia
committed
group f_TD_VoLTE_EMC_INT_ABT_01_02 {
Yann Garcia
committed
function f_mtc_check_precond_TD_VoLTE_EMC_INT_ABT_01_02() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
Yann Garcia
committed
} // End of function f_mtc_check_precond_TD_VoLTE_EMC_INT_ABT_01_02
Yann Garcia
committed
} // End of group f_TD_VoLTE_EMC_INT_ABT_01_02
/**
* @desc To perform SIP session abort (originating side) and the related interactions with PCRF A and EPC A.
* @see ETSI TS 103 795-2 Clause 5.3.3.1 Emergency Session Abort
* @remark This is option 3: PSAP is in PSTN network
Yann Garcia
committed
testcase TD_VoLTE_EMC_INT_ABT_01_03() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_IC_INTERFACENAME // IBCF -> IMS -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
Yann Garcia
committed
f_mtc_check_precond_TD_VoLTE_EMC_INT_ABT_01_03();
// Test body
//f_mtc_userInitiateCall (v_ueA, v_userTelInfoB);
Yann Garcia
committed
f_mtc_check_TP_GM_PCSCF_EMC_CANCEL_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 1
//Rx/Gx exchange after CANCEL was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_STR_01(vc_vxlte_monitor_components.rx); // (STR – Event 2
f_mtc_check_TP_GX_PCRF_RAR_02(vc_vxlte_monitor_components.gx, true); // (RAR – Event 3)
f_mtc_check_TP_GX_PGW_RAA_03(vc_vxlte_monitor_components.gx); // (RAA – Event 4)
f_mtc_check_TP_RX_PCRF_STA_01(vc_vxlte_monitor_components.rx); // (STA – Event 5)
Yann Garcia
committed
f_mtc_check_TP_MW_PCSCF_EMC_CANCEL_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 6
Yann Garcia
committed
f_mtc_check_TP_MI_ECSCF_EMC_CANCEL_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 13
Yann Garcia
committed
f_mtc_check_TP_MM_ECSCF_EMC_CANCEL_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 14
Yann Garcia
committed
f_mtc_check_TP_MI_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 16
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 17
f_mtc_check_TP_GM_PCSCF_200OK_02(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 18
Yann Garcia
committed
f_mtc_check_TP_MM_ECSCF_EMC_487INVITE_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 22
f_mtc_check_TP_MI_ECSCF_EMC_487INVITE_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 23
Yann Garcia
committed
Yann Garcia
committed
f_mtc_check_TP_MW_PCSCF_EMC_487INVITE_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 24
f_mtc_check_TP_GM_PCSCF_487INVITE_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 25
f_mtc_check_TP_GM_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 26
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 27
Yann Garcia
committed
f_mtc_check_TP_MI_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 31
f_mtc_check_TP_MM_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 32
f_mtc_userCheckCallTerminated(v_ueA); // Event 33
f_mtc_userCheckCallCancelled(v_psap); // Event 34
// Postamble
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
Yann Garcia
committed
} // End of TC TD_VoLTE_EMC_INT_ABT_01_03
Yann Garcia
committed
group f_TD_VoLTE_EMC_INT_ABT_01_03 {
Yann Garcia
committed
function f_mtc_check_precond_TD_VoLTE_EMC_INT_ABT_01_03() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
Yann Garcia
committed
} // End of function f_mtc_check_precond_TD_VoLTE_EMC_INT_ABT_01_03
Yann Garcia
committed
} // End of group f_TD_VoLTE_EMC_INT_ABT_01_03
/**
* @desc To demonstrate interaction between UE A and PSAP when an emergency session is rejected.
* @see ETSI TS 103 795-2 5.3.3.2 Emergency Session Reject from PSAP
* @remark This is option 1: PSAP is in IMS A network
*/
testcase TD_VoLTE_ECO_INT_REJ_01_01() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_MW_EB_INTERFACENAME, // E-CSCF -> IBCF
PX_SIP_MM_B_PSAP_INTERFACENAME // E-CSCCF -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_check_precond_TD_VoLTE_ECO_INT_REJ_01_01();
// Test body
//f_mtc_userInitiateCall (v_ueA, v_userTelInfoB);
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 3
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.gmA, -, v_sip);
//Rx/Gx exchange after INVITE (SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_03(vc_vxlte_monitor_components.rx);// Event 4
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 5
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 6
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 7
f_mtc_check_TP_RX_PCSCF_RAA_01(vc_vxlte_monitor_components.rx);// Events 8,9
f_mtc_check_TP_GX_PCRF_CCA_01(vc_vxlte_monitor_components.gx); // Events 10,11
f_mtc_check_TP_MW_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 12
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
f_mtc_check_TP_MW_PCSCF_ECO_INVITE_03(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 13
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
// 480 Temporary Unvailable
Yann Garcia
committed
f_mtc_check_TP_MM_ECSCF_ECO_480INVITE_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 480 Temporary Unavailables Event 14
f_mtc_check_TP_MW_PCSCF_ECO_480INVITE_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 23
f_mtc_check_TP_RX_PCSCF_STR_01(vc_vxlte_monitor_components.rx); // Event 24
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 25
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 26
f_mtc_check_TP_RX_PCRF_STA_01(vc_vxlte_monitor_components.rx); // Event 27
Yann Garcia
committed
f_mtc_check_TP_GM_PCSCF_ECO_380ALTSRV_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 28
f_mtc_check_TP_GM_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 29
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 30
f_mtc_check_TP_MM_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 31
f_mtc_userCheckCallTerminated(v_ueA); // Event 36
f_mtc_userCheckCallCancelled(v_psap); // Event 37
// Postamble
f_PO_user_home_deregistration(v_ueA);
//unmap/disconnect component ports
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_REJ_01_01
group f_TD_VoLTE_ECO_INT_REJ_01_01 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_REJ_01_01() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_REJ_01_01
} // End of group f_TD_VoLTE_ECO_INT_REJ_01_01
* @desc To demonstrate interaction between UE A and PSAP when an emergency session is rejected.
Yann Garcia
committed
* @see ETSI TS 103 795-2 5.3.4.3 Emergency Session Reject
* @remark This is option 1: PSAP is not in IMS A network
testcase TD_VoLTE_ECO_INT_REJ_01_02() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_IC_INTERFACENAME // IBCF -> IMS -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_userRegistration(v_ueA, v_userInfoA);
f_cf_user_down ( v_psap ); // PSAP unavailable
f_mtc_check_precond_TD_VoLTE_ECO_INT_REJ_01_02();
// Test body
//f_mtc_userInitiateCall (v_ueA, v_userTelInfoB);
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 3
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.gmA, -, v_sip);
//Rx/Gx exchange after INVITE (SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_03(vc_vxlte_monitor_components.rx);// Event 4
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 5
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 6
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 7
f_mtc_check_TP_RX_PCSCF_RAA_01(vc_vxlte_monitor_components.rx);// Events 8,9
f_mtc_check_TP_GX_PCRF_CCA_01(vc_vxlte_monitor_components.gx); // Events 10,11
f_mtc_check_TP_MW_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 15
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
f_mtc_check_TP_IC_IBCF_INVITE_01(vc_vxlte_monitor_components.ic); // INVITE Event 16 (NOTE: comment out if ISC simulated by Ic)
f_mtc_check_TP_IC_IBCF_480TEMPAV_01(vc_vxlte_monitor_components.ic, -, v_sip); // INVITE Event 18 (NOTE: comment out if ISC simulated by Ic)
Yann Garcia
committed
Yann Garcia
committed
f_mtc_check_TP_MW_PCSCF_ECO_480INVITE_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 23
f_mtc_check_TP_RX_PCSCF_STR_01(vc_vxlte_monitor_components.rx); // Event 24
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 25
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 26
f_mtc_check_TP_RX_PCRF_STA_01(vc_vxlte_monitor_components.rx); // Event 27
Yann Garcia
committed
f_mtc_check_TP_GM_PCSCF_ECO_380ALTSRV_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 28
f_mtc_check_TP_GM_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 29
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 30
f_mtc_check_TP_IC_IBCF_ACK_01(vc_vxlte_monitor_components.mmB_PSAP); // Event 31
f_mtc_userCheckCallTerminated(v_ueA); // Event 36
f_mtc_userCheckCallCancelled(v_psap); // Event 37
// Postamble
f_PO_user_home_deregistration(v_ueA);
//unmap/disconnect component ports
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_REJ_01_02
group f_TD_VoLTE_ECO_INT_REJ_01_02 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_REJ_01_02() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_REJ_01_02
} // End of group f_TD_VoLTE_ECO_INT_REJ_01_02
/**
* @desc To demonstrate interaction between UE A and PSAP when an emergency session is rejected.
Yann Garcia
committed
* @see ETSI TS 103 795-2 5.3.4.3 Emergency Session Reject
* @remark This is option 1: PSAP is in PSTN network
*/
testcase TD_VoLTE_ECO_INT_REJ_01_03() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_IC_INTERFACENAME // IBCF -> IMS -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_userRegistration(v_ueA, v_userInfoA);
f_cf_user_down ( v_psap ); // PSAP unavailable
f_mtc_check_precond_TD_VoLTE_ECO_INT_REJ_01_03();
// Test body
//f_mtc_userInitiateCall (v_ueA, v_userTelInfoB);
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 3
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.gmA, -, v_sip);
//Rx/Gx exchange after INVITE (SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_03(vc_vxlte_monitor_components.rx);// Event 4
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 5
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 6
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 7
f_mtc_check_TP_RX_PCSCF_RAA_01(vc_vxlte_monitor_components.rx);// Events 8,9
f_mtc_check_TP_GX_PCRF_CCA_01(vc_vxlte_monitor_components.gx); // Events 10,11
f_mtc_check_TP_MW_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 12
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
Yann Garcia
committed
f_mtc_check_TP_MI_ECSCF_ECO_INVITE_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 19
f_mtc_check_TP_MI_ECSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwEB, -, v_sip);
f_mtc_check_TP_MM_ECSCF_ECO_INVITE_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 20
// 480 Temporary Unavailable
Yann Garcia
committed
f_mtc_check_TP_MM_ECSCF_ECO_480INVITE_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 21
f_mtc_check_TP_MI_ECSCF_ECO_480INVITE_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 22
f_mtc_check_TP_MW_PCSCF_ECO_480INVITE_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 23
f_mtc_check_TP_RX_PCSCF_STR_01(vc_vxlte_monitor_components.rx); // Event 24
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 25
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 26
f_mtc_check_TP_RX_PCRF_STA_01(vc_vxlte_monitor_components.rx); // Event 27
Yann Garcia
committed
f_mtc_check_TP_GM_PCSCF_ECO_380ALTSRV_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 28
f_mtc_check_TP_GM_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 29
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 30
Yann Garcia
committed
f_mtc_check_TP_MI_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 34
f_mtc_check_TP_MM_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // ACK – Event 35
f_mtc_userCheckCallTerminated(v_ueA); // Event 33
f_mtc_userCheckCallCancelled(v_psap); // Event 34
// Postamble
f_PO_user_home_deregistration(v_ueA);
//unmap/disconnect component ports
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_REJ_01_03
group f_TD_VoLTE_ECO_INT_REJ_01_03 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_REJ_01_03() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_REJ_01_03
} // End of group f_TD_VoLTE_ECO_INT_REJ_01_03
/**
* @desc To demonstrate interaction between UE A and P-CSCF when an emergency session is rejected.
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5.3.3.3 Emergency Session Reject - IMS not able to handle emergency sessions
testcase TD_VoLTE_ECO_INT_REJ_02() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
// Configure IMS so that IMS is not capable to handle emergency session
f_mtc_check_precond_TD_VoLTE_ECO_INT_REJ_02();
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_01(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 1
Yann Garcia
committed
f_mtc_check_TP_GM_PCSCF_ECO_380ALTSRV_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 2
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 3
// Postamble
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_REJ_02
group f_TD_VoLTE_ECO_INT_REJ_02 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_REJ_02() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
log("Check that IMS is not capable to handle emergency session");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_REJ_02
} // End of group f_TD_VoLTE_ECO_INT_REJ_02
Yann Garcia
committed
/**
* @desc To demonstrate interaction between UE A and P-CSCF when an emergency session is rejected due to wrong urn
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5.3.3.4 Emergency Session Reject – due to wrong urn
Yann Garcia
committed
2948
2949
2950
2951
2952
2953
2954
2955
2956
2957
2958
2959
2960
2961
2962
2963
2964
2965
2966
2967
2968
2969
2970
2971
2972
2973
2974
2975
2976
2977
2978
2979
2980
2981
*/
testcase TD_VoLTE_ECO_INT_REJ_03() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_userRegistration(v_ueA, v_userInfoA);
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TD_VoLTE_ECO_INT_REJ_03();
// Test body
//Send incorrect URN to SIP message
f_mtc_check_TP_GM_PCSCF_ECO_INVALID_INVITE_01(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 1
Yann Garcia
committed
2984
2985
2986
2987
2988
2989
2990
2991
2992
2993
2994
2995
2996
2997
2998
2999
3000
3001
3002
3003
3004
3005
3006
3007
3008
3009
3010
3011
f_mtc_check_TP_GM_PCSCF_ECO_380ALTSRV_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 2
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 3
// Postamble
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_REJ_03
group f_TD_VoLTE_ECO_INT_REJ_03 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_REJ_03() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_REJ_03
} // End of group f_TD_VoLTE_ECO_INT_REJ_03
} // End of group EmergencySessionAbortOrReject
/**
* @see ETSI TS 103 795-2 Clause 5.3.4 NG eCall tests
*/
3020
3021
3022
3023
3024
3025
3026
3027
3028
3029
3030
3031
3032
3033
3034
3035
3036
3037
3038
3039
3040
3041
3042
3043
3044
3045
3046
3047
3048
3049
3050
3051
3052
3053
3054
3055
3056
3057
3058
3059
3060
3061
3062
3063
3064
3065
3066
3067
3068
3069
3070
3071
3072
3073
3074
3075
3076
3077
3078
3079
3080
3081
3082
3083
3084
3085
3086
3087
3088
3089
3090
3091
3092
3093
3094
3095
3096
3097
3098
3099
3100
3101
3102
3103
3104
3105
3106
3107
3108
3109
3110
3111
3112
3113
3114
3115
3116
3117
3118
3119
3120
3121
3122
3123
3124
3125
3126
3127
3128
3129
3130
3131
3132
3133
3134
3135
3136
3137
3138
3139
3140
3141
3142
3143
3144
3145
3146
3147
3148
3149
3150
3151
3152
3153
3154
3155
3156
3157
3158
3159
3160
3161
3162
3163
3164
3165
3166
3167
3168
3169
3170
3171
3172
3173
3174
3175
3176
3177
3178
3179
3180
3181
3182
3183
3184
3185
3186
3187
3188
3189
3190
3191
3192
3193
3194
3195
3196
3197
3198
3199
3200
3201
3202
3203
3204
3205
3206
3207
3208
3209
3210
3211
3212
3213
3214
3215
3216
3217
3218
3219
3220
3221
3222
3223
3224
3225
3226
3227
3228
3229
3230
3231
3232
3233
3234
3235
3236
3237
3238
3239
3240
3241
3242
3243
3244
3245
3246
3247
3248
3249
3250
3251
3252
3253
3254
3255
3256
3257
3258
3259
3260
3261
3262
3263
3264
3265
3266
3267
3268
3269
3270
3271
3272
3273
3274
3275
3276
3277
3278
3279
3280
3281
3282
3283
3284
3285
3286
3287
3288
3289
3290
3291
3292
3293
3294
3295
3296
3297
3298
3299
3300
3301
3302
3303
3304
3305
3306
3307
3308
3309
3310
3311
3312
3313
3314
3315
3316
3317
3318
3319
3320
3321
3322
3323
3324
3325
3326
3327
3328
3329
3330
3331
3332
3333
3334
3335
3336
3337
3338
3339
3340
3341
3342
3343
3344
3345
3346
3347
3348
3349
/**
* @desc To demonstrate the establishment of IMS emergency call of the (automatically or manually) initiated eCall type of emergency service within an emergency registration
* @see ETSI TS 103 795-2 Clause 5.3.4.1 MSD sent during NG eCall establishment
*/
testcase TD_VoLTE_NGC_INT_INI_01() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_MM_B_PSAP_INTERFACENAME // E-CSCCF -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_userRegistration(v_ueA, v_userInfoA);
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TD_VoLTE_NGC_INT_INI_01();
// Test body
f_mtc_check_TP_GM_PCSCF_NGC_INVITE_01(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 1
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.gmA, -, v_sip);
//Rx/Gx exchange after INVITE (SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_03(vc_vxlte_monitor_components.rx);// Event 2
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 3
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 4
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 5
f_mtc_check_TP_RX_PCSCF_RAA_01(vc_vxlte_monitor_components.rx);// Events 7,8
f_mtc_check_TP_GX_PCRF_CCA_01(vc_vxlte_monitor_components.gx); // Events 6,9
f_mtc_check_TP_MW_PCSCF_NGC_INVITE_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 10
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
f_mtc_check_TP_MM_ECSCF_NGC_INVITE_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 11
f_mtc_check_TP_MM_ECSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip);
// 183 Session Progress
f_mtc_check_TP_MM_ECSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 183 In Progress Event 12
f_mtc_check_TP_MW_PCSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 13
f_mtc_check_TP_GM_PCSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 18
//Rx/Gx exchange after 183(SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_04(vc_vxlte_monitor_components.rx);// Event 14
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 15
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 16
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 17
f_mtc_check_TP_MM_ECSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 180 Ringing – Event 20
f_mtc_check_TP_MW_PCSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 21
f_mtc_check_TP_GM_PCSCF_180RINGING_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 22
f_mtc_userCheckRinging(v_psap); // Event 19
f_mtc_userCheckPeerIsRinging(v_ueA); // Event 19
f_mtc_userAnswerCall(v_psap); // Event 26
f_mtc_check_TP_MM_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 200 OK Event 23
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 24
f_mtc_check_TP_GM_PCSCF_200OK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 25
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // ACK Event 26
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 27
f_mtc_check_TP_MM_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // ACK – Event 28
f_mtc_userCheckCallEstablished(v_ueA); // Event 29
f_mtc_userCheckCallEstablished(v_psap); // Event 29
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_NGC_INT_INI_01
group f_TD_VoLTE_NGC_INT_INI_01 {
function f_mtc_check_precond_TD_VoLTE_NGC_INT_INI_01() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_NGC_INT_INI_01
} // End of group f_TD_VoLTE_NGC_INT_INI_01
/**
* @desc To demonstrate the if an IMS emergency call of the (automatically or manually) initiated eCall type of emergency service has been established,
* the attempt by the PSAP to request transfer of an updated MSD shall be answered.
* @see ETSI TS 103 795-2 Clause 5.3.4.1 MSD update during NG eCall
*/
testcase TD_VoLTE_NGC_INT_INF_01_01() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_MM_B_PSAP_INTERFACENAME // E-CSCCF -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_userRegistration(v_ueA, v_userInfoA);
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_userInitiateCall (v_ueA, v_infoPsap); // Event 1
f_mtc_check_precond_TD_VoLTE_NGC_INT_INF_01();
// Test body
//Send INFO
f_mtc_check_TP_MM_ECSCF_NGC_INFO_01(vc_vxlte_monitor_components.mwS_PSAP, -, v_sip); // INFO Event 1
f_mtc_check_TP_MW_PCSCF_NGC_INFO_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // INFO Event 6
f_mtc_check_TP_GM_PCSCF_NGC_INFO_01(vc_vxlte_monitor_components.gmA, -, v_sip); // INFO Event 7
//Receive INFO
f_mtc_check_TP_GM_PCSCF_NGC_INFO_02(vc_vxlte_monitor_components.gmA, -, v_sip); // INFO Event 8
f_mtc_check_TP_MW_PCSCF_NGC_INFO_02(vc_vxlte_monitor_components.mwPE, -, v_sip); // INFO Event 9
f_mtc_check_TP_MM_ECSCF_NGC_INFO_02(vc_vxlte_monitor_components.mwS_PSAP, -, v_sip); // INFO Event 10
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_NGC_INT_INF_01_01
testcase TD_VoLTE_NGC_INT_INF_01_02() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_MW_EB_INTERFACENAME // E-CSCCF -> IBCF
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_userRegistration(v_ueA, v_userInfoA);
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_userInitiateCall (v_ueA, v_infoPsap); // Event 1
f_mtc_check_precond_TD_VoLTE_NGC_INT_INF_01();
// Test body
//Send INFO
f_mtc_check_TP_MX_ECSCF_NGC_INFO_01(vc_vxlte_monitor_components.mwS_PSAP, -, v_sip); // INFO Event 3
f_mtc_check_TP_MW_PCSCF_NGC_INFO_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // INFO Event 6
f_mtc_check_TP_GM_PCSCF_NGC_INFO_01(vc_vxlte_monitor_components.gmA, -, v_sip); // INFO Event 7
//Receive INFO
f_mtc_check_TP_GM_PCSCF_NGC_INFO_02(vc_vxlte_monitor_components.gmA, -, v_sip); // INFO Event 8 TODO
f_mtc_check_TP_MW_PCSCF_NGC_INFO_02(vc_vxlte_monitor_components.mwPE, -, v_sip); // INFO Event 9 TODO
f_mtc_check_TP_MX_ECSCF_NGC_INFO_02(vc_vxlte_monitor_components.mwS_PSAP, -, v_sip); // INFO Event 11
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_NGC_INT_INF_01_02
testcase TD_VoLTE_NGC_INT_INF_01_03() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_MI_EB_INTERFACENAME // E-CSCCF -> BGCF
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_userRegistration(v_ueA, v_userInfoA);
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_userInitiateCall (v_ueA, v_infoPsap); // Event 1
f_mtc_check_precond_TD_VoLTE_NGC_INT_INF_01();
// Test body
//Send INFO
f_mtc_check_TP_MI_ECSCF_NGC_INFO_01(vc_vxlte_monitor_components.mwS_PSAP, -, v_sip); // INFO Event 5
f_mtc_check_TP_MW_PCSCF_NGC_INFO_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // INFO Event 6
f_mtc_check_TP_GM_PCSCF_NGC_INFO_01(vc_vxlte_monitor_components.gmA, -, v_sip); // INFO Event 7
//Receive INFO
f_mtc_check_TP_GM_PCSCF_NGC_INFO_02(vc_vxlte_monitor_components.gmA, -, v_sip); // INFO Event 8 TODO
f_mtc_check_TP_MW_PCSCF_NGC_INFO_02(vc_vxlte_monitor_components.mwPE, -, v_sip); // INFO Event 9 TODO
f_mtc_check_TP_MI_ECSCF_NGC_INFO_02(vc_vxlte_monitor_components.mwS_PSAP, -, v_sip); // INFO Event 13
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_NGC_INT_INF_01_03
group f_TD_VoLTE_NGC_INT_INF_01 {
function f_mtc_check_precond_TD_VoLTE_NGC_INT_INF_01() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_NGC_INT_INI_01
} // End of group f_TD_VoLTE_NGC_INT_INF_01_01
}
} // End of group EmergencySessionEmergencyBearerOperations
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 5.5 Emergency Network Detachment
*/
group EmergencyNetworkDetachment {
group EmergencySessionDetachment {
Yann Garcia
committed
/**
* @desc To demonstrate UE initiated network emergency detachment (IP-CAN session termination) for a UE that has not yet emergency registered to the IMS or for UE that has been emergency registered to the IMS
* @see ETSI TS 103 795-2 Clause 5.5.1 UE Emergency Network Detachment (with/without Emergency Registration)
*/
testcase TC_VoLTE_ECO_INT_DTC_01 ( ) runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_DIAMETER_GX_INTERFACENAME})){
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_VxLteMonitor_Up();
//preamble
f_mtc_userRadioEnabled ( v_ueA, true, true ); // UE-A trigger an initial network_attachment by enabling radio interface of its mobile
Yann Garcia
committed
f_mtc_userRadioEnabled ( v_ueA, false, true );
Yann Garcia
committed
3383
3384
3385
3386
3387
3388
3389
3390
3391
3392
3393
3394
3395
3396
3397
3398
3399
3400
3401
3402
3403
3404
3405
3406
3407
3408
3409
3410
3411
3412
3413
3414
3415
3416
3417
3418
3419
3420
3421
3422
3423
3424
3425
3426
3427
3428
3429
3430
3431
3432
3433
3434
3435
3436
3437
3438
3439
3440
3441
3442
3443
3444
3445
3446
3447
3448
3449
3450
3451
3452
3453
3454
3455
3456
3457
3458
3459
3460
3461
3462
3463
3464
3465
3466
3467
3468
3469
3470
3471
3472
3473
3474
3475
3476
3477
3478
3479
3480
3481
3482
3483
3484
3485
3486
3487
3488
3489
3490
3491
3492
3493
3494
3495
3496
3497
3498
3499
3500
3501
3502
3503
3504
3505
3506
3507
3508
3509
3510
3511
3512
3513
3514
3515
3516
3517
3518
3519
3520
3521
3522
3523
3524
3525
3526
3527
3528
3529
3530
3531
3532
3533
3534
3535
3536
3537
3538
3539
3540
3541
3542
3543
3544
3545
3546
3547
3548
3549
3550
3551
3552
3553
3554
3555
3556
3557
3558
3559
3560
3561
3562
3563
3564
3565
3566
3567
3568
3569
3570
3571
3572
3573
3574
3575
3576
3577
3578
3579
3580
3581
3582
3583
3584
3585
3586
3587
3588
3589
3590
3591
3592
3593
3594
3595
3596
3597
3598
3599
3600
3601
3602
3603
3604
3605
3606
3607
3608
3609
3610
3611
3612
3613
3614
3615
3616
3617
3618
3619
3620
3621
3622
3623
3624
3625
3626
3627
3628
3629
3630
3631
3632
3633
3634
3635
3636
3637
3638
3639
3640
3641
3642
3643
3644
3645
3646
3647
3648
3649
3650
3651
// test body
// Check that user A starts initial network attachment
f_mtc_check_TP_GX_PCRF_EMC_CCA_01(vc_vxlte_monitor_components.gx, false);//f_mtc_check_TP_GX_PCRF_ECO_CCA_02 ( vc_vxlte_monitor_components.gx, false ); // Check (CCA – Event 3)
//postamble
//unmap/disconnect component ports
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
} // End of TC TC_VoLTE_ECO_INT_DTC_01
/**
* @desc To demonstrate UE initiated emergency network detachment (emergency IP-CAN session termination) for a UE that is emergency registered to IMS and also has active emergency session
* @see ETSI TS 103 795-2 Clause 5.5.2 UE Emergency Network Detachment with Previously Established Emergency Registration & Emergency Session
* @remark This is option 1: PSAP is in IMS A network
*/
testcase TC_VoLTE_ECO_INT_DTC_02_01 ( ) runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_MM_B_PSAP_INTERFACENAME // E-CSCCF -> PSAP
})){
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_userRegistration(v_ueA, v_userInfoA);
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TC_VoLTE_ECO_INT_DTC_02_01();
f_mtc_userInitiateCall (v_ueA, v_infoPsap); // Event 1
// Test body
f_mtc_check_TP_GM_PCSCF_ECO_BYE_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 2
//Rx/Gx exchange after BYE was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_STR_01(vc_vxlte_monitor_components.rx); // Event 3
f_mtc_check_TP_GX_PCRF_RAR_02(vc_vxlte_monitor_components.gx, true); // Event 4
f_mtc_check_TP_GX_PGW_RAA_03(vc_vxlte_monitor_components.gx); // Event 5
f_mtc_check_TP_RX_PCRF_STA_01(vc_vxlte_monitor_components.rx); // Event 6
f_mtc_check_TP_MW_PCSCF_ECO_BYE_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 7
f_mtc_check_TP_MM_ECSCF_ECO_BYE_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 8
f_mtc_check_TP_MX_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 13
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 18
f_mtc_check_TP_GM_PCSCF_200OK_02(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 19
f_mtc_check_TP_GX_PCRF_ECO_CCA_02 ( vc_vxlte_monitor_components.gx, false ); // Check (CCA – Event 20)
f_mtc_userCheckCallTerminated(v_ueA); // Event 22
f_mtc_userCheckCallCancelled(v_psap); // Event 23
// Postamble
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
} // End of TC TC_VoLTE_ECO_INT_DTC_02_01
group f_TC_VoLTE_ECO_INT_DTC_02_01 {
function f_mtc_check_precond_TC_VoLTE_ECO_INT_DTC_02_01() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
} // End of function f_mtc_check_precond_TC_VoLTE_ECO_INT_DTC_02_01
} // End of f_TC_VoLTE_ECO_INT_DTC_02_01
/**
* @desc To demonstrate UE initiated emergency network detachment (emergency IP-CAN session termination) for a UE that is emergency registered to IMS and also has active emergency session
* @see ETSI TS 103 795-2 Clause 5.5.2 UE Emergency Network Detachment with Previously Established Emergency Registration & Emergency Session
* @remark This is option 2: PSAP is not in IMS A network
*/
testcase TC_VoLTE_ECO_INT_DTC_02_02 ( ) runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_MW_EB_INTERFACENAME, // E-CSCF -> IBCF
PX_SIP_IC_INTERFACENAME // IBCF -> IMS_B -> PSAP
})){
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_userRegistration(v_ueA, v_userInfoA);
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TC_VoLTE_ECO_INT_DTC_02_02();
f_mtc_userInitiateCall (v_ueA, v_infoPsap); // Event 1
// Test body
f_mtc_check_TP_GM_PCSCF_ECO_BYE_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 2
//Rx/Gx exchange after BYE was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_STR_01(vc_vxlte_monitor_components.rx); // (STR – Event 3
f_mtc_check_TP_GX_PCRF_RAR_02(vc_vxlte_monitor_components.gx, true); // (RAR – Event 4)
f_mtc_check_TP_GX_PGW_RAA_03(vc_vxlte_monitor_components.gx); // (RAA – Event 5)
f_mtc_check_TP_RX_PCRF_STA_01(vc_vxlte_monitor_components.rx); // (STA – Event 6)
f_mtc_check_TP_MW_PCSCF_ECO_BYE_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 7
f_mtc_check_TP_MX_ECSCF_ECO_BYE_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 9
f_mtc_check_TP_IC_IBCF_ECO_BYE_01(vc_vxlte_monitor_components.ic); // Event 10
f_mtc_check_TP_MX_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 15
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 18
f_mtc_check_TP_GM_PCSCF_200OK_02(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 19
f_mtc_check_TP_GX_PCRF_ECO_CCA_02 ( vc_vxlte_monitor_components.gx, false ); // Check (CCA – Event 20)
f_mtc_userCheckCallTerminated(v_ueA); // Event 22
f_mtc_userCheckCallCancelled(v_psap); // Event 23
// Postamble
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
} // End of TC TC_VoLTE_ECO_INT_DTC_02_02
group f_TC_VoLTE_ECO_INT_DTC_02_02 {
function f_mtc_check_precond_TC_VoLTE_ECO_INT_DTC_02_02() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
} // End of function f_mtc_check_precond_TC_VoLTE_ECO_INT_DTC_02_02
} // End of f_TC_VoLTE_ECO_INT_DTC_02_02
/**
* @desc To demonstrate UE initiated emergency network detachment (emergency IP-CAN session termination) for a UE that is emergency registered to IMS and also has active emergency session
* @see ETSI TS 103 795-2 Clause 5.5.2 UE Emergency Network Detachment with Previously Established Emergency Registration & Emergency Session
* @remark This is option 3: PSAP is in PSTN network
*/
testcase TC_VoLTE_ECO_INT_DTC_02_03 ( ) runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME, // E-CSCF -> IBCF
PX_SIP_IC_INTERFACENAME // IBCF -> IMS -> PSAP
})){
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_userRegistration(v_ueA, v_userInfoA);
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TC_VoLTE_ECO_INT_DTC_02_03();
f_mtc_userInitiateCall (v_ueA, v_infoPsap); // Event 1
// Test body
f_mtc_check_TP_GM_PCSCF_ECO_BYE_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 2
//Rx/Gx exchange after BYE was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_STR_01(vc_vxlte_monitor_components.rx); // (STR – Event 3
f_mtc_check_TP_GX_PCRF_RAR_02(vc_vxlte_monitor_components.gx, true); // (RAR – Event 4)
f_mtc_check_TP_GX_PGW_RAA_03(vc_vxlte_monitor_components.gx); // (RAA – Event 5)
f_mtc_check_TP_RX_PCRF_STA_01(vc_vxlte_monitor_components.rx); // (STA – Event 6)
f_mtc_check_TP_MW_PCSCF_ECO_BYE_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 7
f_mtc_check_TP_MI_ECSCF_ECO_BYE_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 11
f_mtc_check_TP_MI_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwEB, -, v_sip); // Event 17
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 18
f_mtc_check_TP_GM_PCSCF_200OK_02(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 19
f_mtc_check_TP_GX_PCRF_ECO_CCA_02 ( vc_vxlte_monitor_components.gx, false ); // Check (CCA – Event 20)
f_mtc_userCheckCallTerminated(v_ueA); // Event 22
f_mtc_userCheckCallCancelled(v_psap); // Event 23
// Postamble
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
} // End of TC TC_VoLTE_ECO_INT_DTC_02_03
group f_TC_VoLTE_ECO_INT_DTC_02_03 {
function f_mtc_check_precond_TC_VoLTE_ECO_INT_DTC_02_03() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
} // End of function f_mtc_check_precond_TC_VoLTE_ECO_INT_DTC_02_03
} // End of f_TC_VoLTE_ECO_INT_DTC_02_03
} // End of group EmergencySessionDetachment
} // End of group EmergencyNetworkDetachment
} // End of group Interoperability
/**
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 6 Test Descriptions (Roaming)
Yann Garcia
committed
* @see ETSI TS 103 795-2 6.1 Network Attachment
group UENetworkAttachmentWithUSIM {
/**
* @desc Emergency Network Attachment and Establishment of the Emergency Bearer with USIM.
* On successful emergency attachment, the UE/IVS should discover the P-CSCF IP address.
* The EPC will create the Emergency Bearers which will allow communication only between the UE and the P-CSCF
* and allowed forwarding towards E-CSCF
* @see ETSI TS 103 795-2 6.1.1 UE Emergency Network Attachment with USIM
* TS 124 229 [2], clause 9.2.1 and L.2.2.6; TS 129 212 [7], clauses 4.5.15 and 4a.5.12;
* TS 129 272 [8], clause 5.2.1.1 (MME shall proceed even if Update Location fails)
*
*/
testcase TC_VoLTE_ECO_RMI_ATT_01 ( ) runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueB := f_cf_create_IotEquipmentUser ( c_userUE_B );
var ImsUserInfo v_userInfoB := f_getImUser ( PX_EUT_B );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_DIAMETER_GX_INTERFACENAME,PX_DIAMETER_S6A_INTERFACENAME})){
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_VxLteMonitor_Up();
// preamble
f_mtc_userRadioEnabled ( v_ueB, true, true ); // UE-B trigger an initial network_attachment by enabling radio interface of its mobile
// TODO: Check that user B starts initial network attachment
f_mtc_check_TP_S6A_MME_ULR_01 ( vc_vxlte_monitor_components.s6a, true ); // Check (ULR – Event 2)
f_mtc_check_TP_S6A_HSS_ECO_ULA_01 ( vc_vxlte_monitor_components.s6a); // Check (ULA – Event 3)
f_mtc_check_TP_GX_PCRF_ECO_CCA_01 ( vc_vxlte_monitor_components.gx); // Check (CCR, CCA – Events 4, 5)
// postamble
f_mtc_userRadioEnabled ( v_ueB, false, true );
//unmap/disconnect component ports
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
} // End of TC TC_VoLTE_ECO_RMI_ATT_01
} // End of group UENetworkAttachmentWithUSIM
group UENetworkAttachmentWithoutUSIM {
/**
* @desc Emergency Network Attachment and Establishment of the Emergency Bearer without USIM.
* On successful emergency attachment, the UE/IVS should discover the P-CSCF IP address.
* The EPC will create the Emergency Bearers which will allow communication only between the UE and the P-CSCF
* and allowed forwarding towards E-CSCF
* @see ETSI TS 103 795-2 6.1.2 UE Emergency Network Attachment without USIM
* TS 124 229 [2], clause 9.2.1 and L.2.2.6; TS 129 212 [7], clauses 4.5.15 and 4a.5.12;
* TS 129 272 [8], clause 5.2.1.1 (MME shall proceed even if Update Location fails)
*
*/
testcase TC_VoLTE_EMC_RMI_ATT_02 ( ) runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueB := f_cf_create_IotEquipmentUser ( c_userUE_B );
var ImsUserInfo v_userInfoB := f_getImUser ( PX_EUT_B );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_DIAMETER_GX_INTERFACENAME,PX_DIAMETER_S6A_INTERFACENAME})){
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_VxLteMonitor_Up();
// preamble
f_mtc_userRadioEnabled ( v_ueB, true, true ); // UE-B trigger an initial network_attachment by enabling radio interface of its mobile
// TODO Check that user B starts initial network attachment
f_mtc_check_TP_S6A_MME_ULR_01 ( vc_vxlte_monitor_components.s6a, true ); // Check (ULR – Event 2)
f_mtc_check_TP_S6A_HSS_ECO_ULA_01 ( vc_vxlte_monitor_components.s6a); // Check (ULA – Event 3)
f_mtc_check_TP_GX_PCRF_EMC_CCA_01 ( vc_vxlte_monitor_components.gx); // Check (CCR, CCA – Events 4, 5)
// postamble
f_mtc_userRadioEnabled ( v_ueB, false, true );
//unmap/disconnect component ports
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
} // End of TC TC_VoLTE_ECO_RMI_ATT_02
} // End of group UENetworkAttachmentWithoutUSIM
} // End of group NetworkAttachment
/**
Yann Garcia
committed
* @see ETSI TS 103 795-2 Clause 6.2 IMS Emergency Registration in a visited network
*/
group IMSEmergencyRegistration {
3774
3775
3776
3777
3778
3779
3780
3781
3782
3783
3784
3785
3786
3787
3788
3789
3790
3791
3792
3793
3794
3795
3796
3797
3798
3799
/**
* @desc To attempt initial emergency registration via the established emergency bearer. In this case, the emergency registration is not successful due to not accepted UE credentials. Emergency call can be established without emergency registration.
* @see ETSI TS 103 795-2 Clause 6.2.1 IMS Emergency Registration - Rejection
* @remark This is option 1: Emergency registration rejected by the visited network
*/
testcase TD_VoLTE_ECO_RMI_REG_01_01() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var ImsUserInfo v_userInfoA := f_getSipUserId ( PX_EUT_A_EMERGENCY );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_SIP_MW_PI_INTERFACENAME,
PX_DIAMETER_CX_SH_INTERFACENAME,
PX_DIAMETER_CX_IH_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME}))
{
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_VxLteMonitor_Up();
// preamble
f_mtc_userRadioEnabled ( v_ueA, true, true ); // UE-A trigger an initial network_attachment by enabling radio interface of its mobile
// Test body
f_mtc_check_TP_GM_PCSCF_ECO_REGISTER_04(vc_vxlte_monitor_components.gmA); // Events 1, 8
f_mtc_check_TP_RX_PCSCF_ECO_AAR_01(vc_vxlte_monitor_components.rx, true);// Event 2 //true because AAR repeated in next TP
f_mtc_check_TP_RX_PCRF_ECO_AAA_01(vc_vxlte_monitor_components.rx); // Event 3
f_mtc_check_TP_MW_ICSCF_ECO_REGISTER_04(vc_vxlte_monitor_components.mwPI); // Event 4, 7
f_mtc_check_TP_CX_HSS_UAA_03(f_getCxInterface(PX_DIAMETER_CX_SINGLE_INTERFACE));// Event 5, 6
3812
3813
3814
3815
3816
3817
3818
3819
3820
3821
3822
3823
3824
3825
3826
3827
3828
3829
3830
3831
3832
3833
3834
3835
3836
3837
3838
3839
3840
3841
3842
3843
3844
3845
3846
3847
3848
3849
3850
3851
3852
// postamble
f_PO_user_home_deregistration ( v_ueA );
f_mtc_userRadioEnabled ( v_ueA, false, true );
//unmap/disconnet component ports
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs");
}
} // End of testcase TD_VoLTE_ECO_RMI_REG_01_01
/**
* @desc To attempt initial emergency registration via the established emergency bearer. In this case, the emergency registration is not successful due to not accepted UE credentials. Emergency call can be established without emergency registration.
* @see ETSI TS 103 795-2 Clause 6.2.1 IMS Emergency Registration - Rejection
* @remark This is option 1: Emergency registration rejected - UE not supporting GIBA
*/
testcase TD_VoLTE_ECO_RMI_REG_01_02() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var ImsUserInfo v_userInfoA := f_getSipUserId ( PX_EUT_A_EMERGENCY );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_SIP_MW_PI_INTERFACENAME,
PX_DIAMETER_CX_SH_INTERFACENAME,
PX_DIAMETER_CX_IH_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME}))
{
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_VxLteMonitor_Up();
// preamble
f_mtc_userRadioEnabled ( v_ueA, true, true ); // UE-A trigger an initial network_attachment by enabling radio interface of its mobile
// Test body
f_mtc_check_TP_GM_PCSCF_ECO_REGISTER_05(vc_vxlte_monitor_components.gmA); // Events 1, 10
f_mtc_check_TP_RX_PCSCF_ECO_AAR_01(vc_vxlte_monitor_components.rx, true);// Event 2 //true because AAR repeated in next TP
f_mtc_check_TP_RX_PCRF_ECO_AAA_01(vc_vxlte_monitor_components.rx); // Event 3
f_mtc_check_TP_MW_ICSCF_ECO_REGISTER_05(vc_vxlte_monitor_components.mwPI); // Event 4, 9
f_mtc_check_TP_CX_HSS_UAA_03(f_getCxInterface(PX_DIAMETER_CX_SINGLE_INTERFACE));// Event 5, 6
// postamble
f_PO_user_home_deregistration ( v_ueA );
f_mtc_userRadioEnabled ( v_ueA, false, true );
//unmap/disconnet component ports
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs");
}
} // End of testcase TD_VoLTE_ECO_RMI_REG_01_02
} // End of group IMSEmergencyRegistration
/**
* @see ETSI TS 103 795-3 Clause 6.3 Emergency Session Establishment(Roaming)
*/
group EmergencySessionEstablishmentRoaming {
3886
3887
3888
3889
3890
3891
3892
3893
3894
3895
3896
3897
3898
3899
3900
3901
3902
3903
3904
3905
3906
3907
3908
3909
3910
3911
3912
3913
3914
3915
3916
3917
3918
3919
3920
3921
3922
3923
3924
3925
3926
3927
3928
3929
3930
3931
3932
3933
3934
3935
3936
3937
3938
3939
3940
3941
3942
3943
3944
3945
3946
3947
3948
3949
3950
3951
3952
3953
3954
3955
3956
3957
3958
3959
3960
3961
3962
3963
3964
3965
3966
3967
3968
3969
3970
3971
3972
3973
3974
3975
3976
3977
3978
3979
3980
3981
3982
3983
3984
3985
3986
3987
3988
3989
3990
3991
3992
3993
3994
3995
3996
3997
3998
3999
4000
4001
4002
4003
4004
4005
4006
4007
4008
4009
4010
4011
4012
4013
4014
4015
4016
4017
4018
4019
4020
4021
4022
4023
4024
4025
4026
4027
4028
4029
4030
4031
4032
4033
4034
4035
4036
4037
4038
4039
4040
4041
4042
4043
4044
4045
4046
4047
4048
4049
4050
4051
4052
4053
4054
4055
4056
4057
4058
4059
4060
4061
4062
4063
4064
4065
4066
4067
4068
4069
4070
4071
4072
4073
4074
4075
4076
4077
4078
4079
4080
4081
4082
4083
4084
4085
4086
4087
4088
4089
4090
4091
4092
4093
4094
4095
4096
4097
4098
4099
4100
4101
4102
4103
4104
4105
4106
4107
4108
4109
4110
4111
4112
4113
4114
4115
4116
4117
4118
4119
4120
4121
4122
4123
4124
4125
4126
4127
4128
4129
4130
4131
4132
4133
4134
4135
4136
4137
4138
4139
4140
4141
4142
4143
4144
4145
4146
4147
4148
/**
* @see ETSI TS 103 795-3 Clause 6.3.1 Roaming UE calling PSAP with emergency registration
*/
group RoamingUECallingPSAPWithEmergencyRegistration {
/**
* @desc To demonstrate the establishment of dedicated bearers at the originating EPC due to SIP roaming emergency session establishment within an emergency registration.
* PSAP is located in the IM CN subsystem of IMS A
* @see ETSI TS 103 795-2 Clause 6.3.1 Roaming UE calling PSAP with emergency registration
*/
testcase TD_VoLTE_ECO_RMI_INI_01() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueB := f_cf_create_IotEquipmentUser ( c_userUE_B_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoB := f_getImUser ( PX_EUT_B_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_MM_B_PSAP_INTERFACENAME // E-CSCCF -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueB );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_userRegistration(v_ueB, v_userInfoB);
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TD_VoLTE_ECO_RMI_INI_01();
// Test body
if (not PX_ECALL) {
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.gmB, -, v_sip); // INVITE Event 1
} else {
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_04(vc_vxlte_monitor_components.gmB, -, v_sip); // INVITE Event 1
}
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.gmB, -, v_sip);
//Rx/Gx exchange after INVITE (SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_03(vc_vxlte_monitor_components.rx);// Event 2
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 3
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 4
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 5
f_mtc_check_TP_RX_PCSCF_RAA_01(vc_vxlte_monitor_components.rx);// Events 7,8
f_mtc_check_TP_GX_PCRF_CCA_01(vc_vxlte_monitor_components.gx); // Events 6,9
f_mtc_check_TP_MW_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 10
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
f_mtc_check_TP_MM_ECSCF_ECO_INVITE_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 11
f_mtc_check_TP_MM_ECSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip);
// 183 Session Progress
f_mtc_check_TP_MM_ECSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 183 In Progress Event 12
f_mtc_check_TP_MW_PCSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 13
f_mtc_check_TP_GM_PCSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.gmB, -, v_sip); // Event 18
//Rx/Gx exchange after 183(SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_04(vc_vxlte_monitor_components.rx);// Event 14
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 15
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 16
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 17
f_mtc_check_TP_MM_ECSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 180 Ringing – Event 20
f_mtc_check_TP_MW_PCSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 21
f_mtc_check_TP_GM_PCSCF_180RINGING_01(vc_vxlte_monitor_components.gmB, -, v_sip); // Event 22
f_mtc_userCheckRinging(v_psap); // Event 19
f_mtc_userCheckPeerIsRinging(v_ueB); // Event 19
f_mtc_userAnswerCall(v_psap);
f_mtc_check_TP_MM_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 200 OK Event 23
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 24
f_mtc_check_TP_GM_PCSCF_200OK_01(vc_vxlte_monitor_components.gmB, -, v_sip); // Event 25
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmB, -, v_sip); // ACK Event 26
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // ACK Event 27
f_mtc_check_TP_MM_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // ACK – Event 28
f_mtc_userCheckCallEstablished(v_ueB); // Event 29
f_mtc_userCheckCallEstablished(v_psap); // Event 29
// Postamble
f_mtc_EndCall(v_ueB);
f_PO_user_home_deregistration(v_ueB);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueB );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_INI_01
group f_TD_VoLTE_ECO_RMI_INI_01 {
function f_mtc_check_precond_TD_VoLTE_ECO_RMI_INI_01() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_RMI_INI_01
} // End of group f_TD_VoLTE_ECO_RMI_INI_01
} // End of group RoamingUECallingPSAPWithEmergencyRegistration
/**
* @see ETSI TS 103 795-3 Clause 6.3.2 Roaming UE calling PSAP with non-emergency registration
*/
group RoamingUECallingPSAPWithNonEmergencyRegistration {
/**
* @desc To demonstrate the establishment of dedicated bearers at the originating EPC due to roaming SIP emergency session establishment within non-emergency registration.
* PSAP is located in the IM CN subsystem of IMS A
* @see ETSI TS 103 795-2 Clause 6.3.2.1 Roaming UE calling PSAP in same network
*/
testcase TD_VoLTE_ECO_RMI_INI_02() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueB := f_cf_create_IotEquipmentUser ( c_userUE_B_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoB := f_getImUser ( PX_EUT_B ); //non-emergency registration
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMB_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_MM_B_PSAP_INTERFACENAME // E-CSCCF -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueB );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_userRegistration(v_ueB, v_userInfoB);
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TD_VoLTE_ECO_RMI_INI_02();
// Test body
// Test body
if (not PX_ECALL) {
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.gmB, -, v_sip); // INVITE Event 1
} else {
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_04(vc_vxlte_monitor_components.gmB, -, v_sip); // INVITE Event 1
}
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.gmB, -, v_sip);
//Rx/Gx exchange after INVITE (SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_03(vc_vxlte_monitor_components.rx);// Event 2
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 3
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 4
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 5
f_mtc_check_TP_RX_PCSCF_RAA_01(vc_vxlte_monitor_components.rx);// Events 7,8
f_mtc_check_TP_GX_PCRF_CCA_01(vc_vxlte_monitor_components.gx); // Events 6,9
f_mtc_check_TP_MW_PCSCF_ECO_INVITE_02(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 10
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
f_mtc_check_TP_MM_ECSCF_ECO_INVITE_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 11
f_mtc_check_TP_MM_ECSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip);
// 183 Session Progress
f_mtc_check_TP_MM_ECSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 183 In Progress Event 12
f_mtc_check_TP_MW_PCSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 13
f_mtc_check_TP_GM_PCSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.gmB, -, v_sip); // Event 18
//Rx/Gx exchange after 183(SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_04(vc_vxlte_monitor_components.rx);// Event 14
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 15
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 16
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 17
f_mtc_check_TP_MM_ECSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 180 Ringing – Event 20
f_mtc_check_TP_MW_PCSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 21
f_mtc_check_TP_GM_PCSCF_180RINGING_01(vc_vxlte_monitor_components.gmB, -, v_sip); // Event 22
f_mtc_userCheckRinging(v_psap); // Event 19
f_mtc_userCheckPeerIsRinging(v_ueB); // Event 19
f_mtc_userAnswerCall(v_psap);
f_mtc_check_TP_MM_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 200 OK Event 23
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 24
f_mtc_check_TP_GM_PCSCF_200OK_01(vc_vxlte_monitor_components.gmB, -, v_sip); // Event 25
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmB, -, v_sip); // ACK Event 26
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // ACK Event 27
f_mtc_check_TP_MM_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // ACK – Event 28
f_mtc_userCheckCallEstablished(v_ueB); // Event 29
f_mtc_userCheckCallEstablished(v_psap); // Event 29
// Postamble
f_mtc_EndCall(v_ueB);
f_PO_user_home_deregistration(v_ueB);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueB );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_RMI_INI_02
group f_TD_VoLTE_ECO_RMI_INI_02 {
function f_mtc_check_precond_TD_VoLTE_ECO_RMI_INI_02() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_02
} // End of group f_TD_VoLTE_ECO_RMI_INI_02
/**
* @desc To demonstrate the rejection of roaming UE emergency session establishment when the
* P-CFCF is in home operator's network within non-emergency registration.
* P-CFCF is located in the IM CN subsystem of IMS A
* @see ETSI TS 103 795-2 Clause 6.3.2.2 Roaming UE calling PSAP in home operator's network
*/
testcase TD_VoLTE_ECO_RMI_INI_03() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A ); //non-emergency registration
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_VxLteMonitor_Up();
// Preamble
//registration is not needed
//similar to TC_VxLTE_RMI_ATT_01 UE A has perform a network_attachment
f_mtc_userRadioEnabled ( v_ueA, true, true ); // UE-A trigger an initial network_attachment by enabling radio interface of its mobile
// UE A requests emergency session initiation // Event 1
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_05(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 2
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.gmA, -, v_sip);
// 380 (Alternative Service)
f_mtc_check_TP_GM_PCSCF_ECO_380ALTSRV_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 3
// ACK
f_mtc_check_TP_GM_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 6
4177
4178
4179
4180
4181
4182
4183
4184
4185
4186
4187
4188
4189
4190
4191
4192
4193
4194
4195
4196
4197
4198
4199
4200
4201
4202
4203
4204
4205
4206
4207
4208
4209
4210
4211
4212
4213
4214
4215
4216
4217
4218
4219
4220
4221
4222
4223
4224
4225
4226
4227
4228
4229
4230
4231
4232
4233
4234
4235
4236
4237
4238
4239
4240
4241
4242
4243
4244
4245
4246
4247
4248
4249
4250
4251
4252
4253
4254
4255
4256
4257
4258
4259
4260
4261
4262
4263
4264
4265
4266
4267
4268
4269
4270
4271
4272
4273
4274
4275
4276
4277
4278
4279
4280
4281
4282
4283
4284
4285
4286
4287
4288
4289
4290
4291
4292
4293
4294
4295
4296
4297
4298
4299
4300
4301
4302
4303
4304
4305
4306
4307
4308
4309
4310
//unmap/disconnect component ports
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_RMI_INI_02
group f_TD_VoLTE_ECO_RMI_INI_03 {
function f_mtc_check_precond_TD_VoLTE_ECO_RMI_INI_03() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_02
} // End of group f_TD_VoLTE_ECO_RMI_INI_03
/**
* @desc To demonstrate the establishment of dedicated bearers for a roaming UE without any registration.
* PSAP is located in the IM CN subsystem of IMS A
* @see ETSI TS 103 795-2 Clause 6.3.2.3 Roaming UE calling PSAP with non-registration
*/
testcase TD_VoLTE_ECO_RMI_INI_04() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueB := f_cf_create_IotEquipmentUser ( c_userUE_B_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMB_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_MM_B_PSAP_INTERFACENAME // E-CSCCF -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueB );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
//UE B non-registered
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TD_VoLTE_ECO_RMI_INI_04();
// Test body
f_mtc_check_TP_GM_PCSCF_ECO_INVITE_03(vc_vxlte_monitor_components.gmB, -, v_sip); // INVITE Event 1
f_mtc_check_TP_GM_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.gmB, -, v_sip);
//Rx/Gx exchange after INVITE (SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_03(vc_vxlte_monitor_components.rx);// Event 2
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 3
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 4
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 5
f_mtc_check_TP_RX_PCSCF_RAA_01(vc_vxlte_monitor_components.rx);// Events 7,8
f_mtc_check_TP_GX_PCRF_CCA_01(vc_vxlte_monitor_components.gx); // Events 6,9
f_mtc_check_TP_MW_PCSCF_ECO_INVITE_03(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 10
f_mtc_check_TP_MW_PCSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
f_mtc_check_TP_MM_ECSCF_ECO_INVITE_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // Event 11
f_mtc_check_TP_MM_ECSCF_ECO_100Trying_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip);
// 183 Session Progress
f_mtc_check_TP_MM_ECSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 183 In Progress Event 12
f_mtc_check_TP_MW_PCSCF_ECO_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 13
f_mtc_check_TP_GM_PCSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.gmB, -, v_sip); // Event 18
//Rx/Gx exchange after 183(SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_04(vc_vxlte_monitor_components.rx);// Event 14
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 15
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 16
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 17
f_mtc_check_TP_MM_ECSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 180 Ringing – Event 22
f_mtc_check_TP_MW_PCSCF_ECO_180RINGING_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 24
f_mtc_check_TP_GM_PCSCF_180RINGING_01(vc_vxlte_monitor_components.gmB, -, v_sip); // Event 25
f_mtc_userCheckRinging(v_psap); // Event 19
f_mtc_userCheckPeerIsRinging(v_ueB); // Event 19
f_mtc_userAnswerCall(v_psap); // Event 26
f_mtc_check_TP_MM_ECSCF_ECO_200OK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // 200 OK Event 23
f_mtc_check_TP_MW_PCSCF_ECO_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 24
f_mtc_check_TP_GM_PCSCF_200OK_01(vc_vxlte_monitor_components.gmB, -, v_sip); // Event 25
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmB, -, v_sip); // Event 26
f_mtc_check_TP_MW_PCSCF_ECO_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 27
f_mtc_check_TP_MM_ECSCF_ECO_ACK_01(vc_vxlte_monitor_components.mmB_PSAP, -, v_sip); // ACK – Event 28
f_mtc_userCheckCallEstablished(v_ueB); // Event 29
f_mtc_userCheckCallEstablished(v_psap); // Event 29
// Postamble
f_mtc_EndCall(v_ueB);
f_PO_user_home_deregistration(v_ueB);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueB );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
}
group f_TD_VoLTE_ECO_RMI_INI_04 {
function f_mtc_check_precond_TD_VoLTE_ECO_RMI_INI_04() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_04
} // End of group f_TD_VoLTE_ECO_RMI_INI_02
} // End of group RoamingUECallingPSAPWithNonEmergencyRegistration
} // End of group EmergencySessionEstablishmentRoaming
} // End of group Roaming
} // End of module AtsImsIot_Emergency