Newer
Older
/**
* @author TTF 010
* @version $Id: $
* @desc This module provides ATS specific test case definitions for IMS Emergency calls.
* @see ETSI TS 103 795-2
*/
module AtsImsIot_Emergency {
// LibCommon
// LibSip
// LibIms
import from LibIot_TestInterface all;
import from LibIot_TestConfiguration all;
import from LibIot_PIXITS all;
import from LibIot_VxLTE_PIXITS all;
import from LibIot_VxLTE_Functions all;
// LibImsIot
// ImsIot
import from AtsImsIot_TestConfiguration all;
import from AtsImsIot_TestSystem all;
import from AtsImsIot_Functions all;
import from AtsImsIot_TP_behavior_GM all;
import from AtsImsIot_TP_behavior_MW_PS all;
import from AtsImsIot_TP_behavior_MW_SI all;
import from AtsImsIot_TP_behavior_MW_IS all;
import from AtsImsIot_TP_behavior_MW_EC all;
import from AtsImsIot_TP_behavior_MW_EB all;
import from AtsImsIot_TP_behavior_MM all;
import from AtsImsIot_TP_behavior_IC all;
import from AtsImsIot_TP_behavior_CX all;
import from AtsImsIot_TP_behavior_GX all;
import from AtsImsIot_TP_behavior_ISC all;
import from AtsImsIot_TP_behavior_S6A all;
import from AtsImsIot_TP_behavior_S9 all;
import from AtsImsIot_TP_behavior_SH all;
import from AtsImsIot_TP_behavior_RX all;
/**
* @see ETSI TS 103 795-2 Clause 5 Test Descriptions (Interoperability at HPLMN)
*/
group Interoperability {
/**
* @see ETSI TS 103 795-2 Clause 5.1 Network Attachment
*/
group NetworkAttachment {
group UENetworkAttachmentWithUSIM {
/**
* @desc Emergency Network Attachment and Establishment of the Emergency Bearer with USIM.
* On successful emergency attachment, the UE/IVS should discover the P-CSCF IP address.
* The EPC will create the Emergency Bearers which will allow communication only between the UE and the P-CSCF
* and allowed forwarding towards E-CSCF
* @see TS 124 229 [2], clause 9.2.1 and L.2.2.6; TS 129 212 [7], clauses 4.5.15 and 4a.5.12;
* TS 129 272 [8], clause 5.2.1.1 (MME shall proceed even if Update Location fails)
*
*/
testcase TC_VoLTE_ECO_INT_ATT_01 ( ) runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_DIAMETER_GX_INTERFACENAME,PX_DIAMETER_S6A_INTERFACENAME})){
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_VxLteMonitor_Up();
// preamble
f_mtc_userRadioEnabled ( v_ueA, true, true ); // UA-A trigger an initial network_attachment by enabling radio interface of its mobile
// test body
// Check that user A starts initial network attachment
f_mtc_check_TP_S6A_MME_ULR_01 ( vc_vxlte_monitor_components.s6a, true ); // Check (ULR – Event 2)
f_mtc_check_TP_S6A_HSS_ECO_ULA_01 ( vc_vxlte_monitor_components.s6a); // Check (ULA – Event 3)
f_mtc_check_TP_GX_PCRF_ECO_CCA_01 ( vc_vxlte_monitor_components.gx); // Check (CCR, CCA – Events 4, 5)
// postamble
f_mtc_userRadioEnabled ( v_ueA, false, true );
//unmap/disconnect component ports
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
} // End of group UENetworkAttachmentWithUSIM
group UENetworkAttachmentWithoutUSIM {
/**
* @desc Emergency Network Attachment and Establishment of the Emergency Bearer without USIM.
* On successful emergency attachment, the UE/IVS should discover the P-CSCF IP address.
* The EPC will create the Emergency Bearers which will allow communication only between the UE and the P-CSCF
* and allowed forwarding towards E-CSCF
* @see TS 124 229 [2], clause 9.2.1 and L.2.2.6; TS 129 212 [7], clauses 4.5.15 and 4a.5.12;
* TS 129 272 [8], clause 5.2.1.1 (MME shall proceed even if Update Location fails)
*
*/
testcase TC_VoLTE_EMC_INT_ATT_02 ( ) runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_DIAMETER_GX_INTERFACENAME,PX_DIAMETER_S6A_INTERFACENAME})){
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_VxLteMonitor_Up();
// preamble
f_mtc_userRadioEnabled ( v_ueA, true, true ); // UA-A trigger an initial network_attachment by enabling radio interface of its mobile
// test body
// Check that user A starts initial network attachment
f_mtc_check_TP_S6A_MME_ULR_01 ( vc_vxlte_monitor_components.s6a, true ); // Check (ULR – Event 2)
f_mtc_check_TP_S6A_HSS_ECO_ULA_01 ( vc_vxlte_monitor_components.s6a); // Check (ULA – Event 3)
f_mtc_check_TP_GX_PCRF_EMC_CCA_01 ( vc_vxlte_monitor_components.gx); // Check (CCR, CCA – Events 4, 5)
// postamble
f_mtc_userRadioEnabled ( v_ueA, false, true );
//unmap/disconnect component ports
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
} // End of TC TC_VoLTE_ECO_INT_ATT_02
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
} // End of group UENetworkAttachmentWithoutUSIM
} // End of group NetworkAttachment
/**
* @see ETSI TS 103 795-2 Clause 5.2 IMS Emergency Registration
*/
group EmergencyRegistration {
/**
* @desc To perform emergency registration via the established emergency bearer. Note that some UEs perform emergency registration automatically on attachment - in which case this test becomes merged with the previous ones.
* @see ETSI TS 103 795-2 Clause 5.2.1 IMS Emergency Registration - Successful
*/
testcase TD_VoLTE_ECO_INT_REG_01() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A );
var ImsUserInfo v_userInfoA := f_getSipUserId ( PX_EUT_A );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_SIP_MW_PI_INTERFACENAME,
PX_SIP_MW_IS_INTERFACENAME,
PX_DIAMETER_CX_SH_INTERFACENAME,
PX_DIAMETER_CX_IH_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME}))
{
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_VxLteMonitor_Up();
// preamble
f_mtc_userRadioEnabled ( v_ueA, true, true ); // UA-A trigger an initial network_attachment by enabling radio interface of its mobile
// Test body
f_mtc_check_TP_GM_PCSCF_ECO_REGISTER_01(vc_vxlte_monitor_components.gmA); // Events 1, 12
f_mtc_check_TP_MW_PCSCF_ECO_REGISTER_01(vc_vxlte_monitor_components.mwPI); // Event 4, 11
f_mtc_check_TP_MW_ICSCF_ECO_REGISTER_01(vc_vxlte_monitor_components.mwIS, true); // Event 7, 10
f_mtc_check_TP_CX_HSS_ECO_UAA_01(f_getCxInterface(PX_DIAMETER_CX_SINGLE_INTERFACE));// Event 5, 6
f_mtc_check_TP_CX_HSS_MAA_01(vc_vxlte_monitor_components.cxSH);// Event 8, 9
f_mtc_check_TP_GM_PCSCF_ECO_REGISTER_02(vc_vxlte_monitor_components.gmA); // Events 13, 22
f_mtc_check_TP_MW_PCSCF_ECO_REGISTER_02(vc_vxlte_monitor_components.mwPI); // Events 14, 21
f_mtc_check_TP_MW_ICSCF_ECO_REGISTER_02(vc_vxlte_monitor_components.mwIS, true); // Event 17, 20
f_mtc_check_TP_CX_HSS_ECO_UAA_02(f_getCxInterface(PX_DIAMETER_CX_SINGLE_INTERFACE));// Event 15, 16
f_mtc_check_TP_CX_HSS_SAA_01(vc_vxlte_monitor_components.cxSH);// Event 18, 19
// postamble
f_PO_user_home_deregistration ( v_ueA );
f_mtc_userRadioEnabled ( v_ueA, false, true );
//unmap/disconnet component ports
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs");
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
}
} // End of testcase TD_VoLTE_ECO_INT_REG_01
/**
* @desc To attempt initial emergency registration via the established emergency bearer. In this case, the emergency registration is not successful due to not accepted UE credentials. Emergency call can be established without emergency registration.
* @see ETSI TS 103 795-2 Clause 5.2.2 IMS Emergency Registration - Unsuccessful
*/
testcase TD_VoLTE_ECO_INT_REG_02() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A );
var ImsUserInfo v_userInfoA := f_getSipUserId ( PX_EUT_A );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_SIP_MW_PI_INTERFACENAME,
PX_SIP_MW_IS_INTERFACENAME,
PX_DIAMETER_CX_SH_INTERFACENAME,
PX_DIAMETER_CX_IH_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME}))
{
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_VxLteMonitor_Up();
// preamble
f_mtc_userRadioEnabled ( v_ueA, true, true ); // UA-A trigger an initial network_attachment by enabling radio interface of its mobile
// Test body
f_mtc_check_TP_GM_PCSCF_ECO_REGISTER_01(vc_vxlte_monitor_components.gmA); // Events 1, 12
f_mtc_check_TP_MW_PCSCF_ECO_REGISTER_01(vc_vxlte_monitor_components.mwPI); // Event 4, 11
f_mtc_check_TP_MW_ICSCF_ECO_REGISTER_01(vc_vxlte_monitor_components.mwIS, true); // Event 7, 10
f_mtc_check_TP_CX_HSS_ECO_UAA_01(f_getCxInterface(PX_DIAMETER_CX_SINGLE_INTERFACE));// Event 5, 6
f_mtc_check_TP_CX_HSS_MAA_01(vc_vxlte_monitor_components.cxSH);// Event 8, 9
f_mtc_check_TP_GM_PCSCF_ECO_REGISTER_03(vc_vxlte_monitor_components.gmA); // Events 13, 22
f_mtc_check_TP_MW_PCSCF_ECO_REGISTER_03(vc_vxlte_monitor_components.mwPI); // Events 14, 21
f_mtc_check_TP_MW_ICSCF_REGISTER_03(vc_vxlte_monitor_components.mwIS, true); // Event 17, 20
f_mtc_check_TP_CX_HSS_ECO_ECO_UAA_02(f_getCxInterface(PX_DIAMETER_CX_SINGLE_INTERFACE));// Event 15, 16
f_mtc_check_TP_CX_HSS_SAA_01(vc_vxlte_monitor_components.cxSH);// Event 18, 19
// postamble
f_PO_user_home_deregistration ( v_ueA );
f_mtc_userRadioEnabled ( v_ueA, false, true );
//unmap/disconnet component ports
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
f_cf_adapter_down ( );
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs");
}
} // End of testcase TD_VoLTE_ECO_INT_REG_02
} // End of group EmergencyRegistration
/**
* @see ETSI TS 103 795-2 Clause 5.3 Emergency Session and Emergency Bearer Operations
*/
group EmergencySessionEmergencyBearerOperations {
group EmergencySessionEstablishment {
* @desc To demonstrate the establishment of dedicated bearers at the originating EPC due to SIP emergency session establishment.
* On successful emergency call setup with UE-A attached to EPC A, the P-CSCF should derive from the SDP offer and answer, descriptions of the Service Data Flow
* @see ETSI TS 103 795-2 Clause 5.3.1.2 UE calling PSAP with emergency registration
* @remark This is option1: IBCF is connected to another IMS network and the interface between the IBCF and the PSAP is the Ic interface
*/
testcase TD_VoLTE_ECO_INT_INI_01_01 ( ) runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_EB_INTERFACENAME, // E-CSCF -> IBCF
PX_SIP_IC_INTERFACENAME // IBCF -> IMS_B -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_userRegistration(v_ueA, v_userInfoA);
// PSAP is not known from the IMS A
f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_01_01();
// Test body
//f_mtc_userInitiateCall (v_ueA, v_userTelInfoB);
f_mtc_check_TP_GM_PCSCF_INVITE_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 1
f_mtc_check_TP_GM_PCSCF_100Trying_01(vc_vxlte_monitor_components.gmA, -, v_sip);
//Rx/Gx exchange after INVITE (SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_03(vc_vxlte_monitor_components.rx);// Event 2
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 3
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 4
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 5
f_mtc_check_TP_RX_PCSCF_RAA_01(vc_vxlte_monitor_components.rx);// Events 7,8
//f_mtc_check_TP_GX_PCRF_CCA_01(vc_vxlte_monitor_components.gx); // Events 6,9
f_mtc_check_TP_MW_ECSCF_INVITE_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 10
f_mtc_check_TP_MW_ECSCF_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
f_mtc_check_TP_MW_IBCF_INVITE_01(vc_vxlte_monitor_components.mwBE, -, v_sip); // Event 11
f_mtc_check_TP_MW_IBCF_100Trying_01(vc_vxlte_monitor_components.mwBE, -, v_sip);
f_mtc_check_TP_IC_IBCF_INVITE_01(vc_vxlte_monitor_components.ic, true); // INVITE Event 12 (NOTE: comment out if ISC simulated by Ic)
f_mtc_check_TP_IC_IBCF_INVITE_02(vc_vxlte_monitor_components.ic, true); // INVITE Event 12 (NOTE: comment out if ISC simulated by Ic)
f_mtc_check_TP_IC_IBCF_INVITE_03(vc_vxlte_monitor_components.ic); // INVITE ENUM Event 8
f_mtc_check_TP_IC_IBCF_183RESP_01(vc_vxlte_monitor_components.ic,-); // 183 Event 13
// 183 Session Progress
f_mtc_check_TP_MW_IBCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwBE, -, v_sip); // Event 14
f_mtc_check_TP_MW_ECSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 15
f_mtc_check_TP_GM_PCSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 20
//Rx/Gx exchange after 183(SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_04(vc_vxlte_monitor_components.rx);// Event 16
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 17
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 18
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 19
f_mtc_check_TP_IC_IBCF_180RINGING_01(vc_vxlte_monitor_components.ic, true); // 180 Ringing – Event 22
f_mtc_check_TP_MW_IBCF_180RINGING_01(vc_vxlte_monitor_components.mwBE, -, v_sip); // Event 23
f_mtc_check_TP_MW_ECSCF_180RINGING_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 24
f_mtc_check_TP_GM_PCSCF_180RINGING_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 25
f_mtc_userCheckRinging(v_psap);
f_mtc_userCheckPeerIsRinging(v_ueA);
f_mtc_userAnswerCall(v_psap);
f_mtc_check_TP_IC_IBCF_2XXRESP_01(vc_vxlte_monitor_components.ic, true); // 200 OK – Event 26
f_mtc_check_TP_IC_IBCF_2XXRESP_02(vc_vxlte_monitor_components.ic, true); // 200 OK – Event 26
f_mtc_check_TP_IC_IBCF_2XXRESP_03(vc_vxlte_monitor_components.ic); // 200 OK – Event 26
f_mtc_check_TP_MW_IBCF_200OK_01(vc_vxlte_monitor_components.mwBE, -, v_sip); // Event 27
f_mtc_check_TP_MW_ECSCF_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 28
f_mtc_check_TP_GM_PCSCF_200OK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 29
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 30
f_mtc_check_TP_MW_ECSCF_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 31
f_mtc_check_TP_MW_IBSCF_ACK_01(vc_vxlte_monitor_components.mwBE, -, v_sip); // Event 32
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
f_mtc_check_TP_IC_IBCF_ACK_01(vc_vxlte_monitor_components.ic); // ACK – Event 33
f_mtc_userCheckCallEstablished(v_ueA); // Event 34
f_mtc_userCheckCallEstablished(v_psap); // Event 34
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_INI_01_01
group f_TD_VoLTE_ECO_INT_INI_01_01 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_01_01() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_01_01
} // End of f_TD_VoLTE_ECO_INT_INI_01_01
/**
* @desc To demonstrate the establishment of dedicated bearers at the originating EPC due to SIP emergency session establishment.
* On successful emergency call setup with UE-A attached to EPC A, the P-CSCF should derive from the SDP offer and answer, descriptions of the Service Data Flow
* @see ETSI TS 103 795-2 Clause 5.3.1.2 UE calling PSAP with emergency registration
* @remark This is option2: IBCF is connected to the PSAP, the interface IBCF and the PSAP is the Mm interface
*/
testcase TD_VoLTE_ECO_INT_INI_01_02() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_EB_INTERFACENAME, // E-CSCF -> IBCF
PX_SIP_MM_PSAP_INTERFACENAME // IBCF -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_userRegistration(v_ueA, v_userInfoA);
if (PX_PSAP_REGISTERED) {
f_mtc_userRegistration(v_psap, v_infoPsap);
} else {
// TODO Check OPTIONS from PSAP to E-CSCF
}
f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_01_02();
// Test body
//f_mtc_userInitiateCall (v_ueA, v_userTelInfoB);
f_mtc_check_TP_GM_PCSCF_INVITE_01(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 1
f_mtc_check_TP_GM_PCSCF_100Trying_01(vc_vxlte_monitor_components.gmA, -, v_sip);
//Rx/Gx exchange after INVITE (SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_03(vc_vxlte_monitor_components.rx);// Event 2
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 3
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 4
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 5
f_mtc_check_TP_RX_PCSCF_RAA_01(vc_vxlte_monitor_components.rx);// Events 7,8
f_mtc_check_TP_GX_PCRF_CCA_01(vc_vxlte_monitor_components.gx); // Events 6,9
f_mtc_check_TP_MW_ECSCF_INVITE_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 10
f_mtc_check_TP_MW_ECSCF_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
f_mtc_check_TP_MW_IBCF_INVITE_01(vc_vxlte_monitor_components.mwBE, -, v_sip); // Event 11
f_mtc_check_TP_MW_IBCF_100Trying_01(vc_vxlte_monitor_components.mwBE, -, v_sip);
f_mtc_check_TP_MM_PSAP_INVITE_01(vc_vxlte_monitor_components.mwB_PSAP, true); // Event 12
f_mtc_check_TP_MM_PSAP_100Trying_01(vc_vxlte_monitor_components.mwB_PSAP, -, v_sip);
// 183 Session Progress
f_mtc_check_TP_MM_PSAP_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwB_PSAP, -, v_sip); // Event 13
f_mtc_check_TP_MW_IBCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwBE, -, v_sip); // Event 14
f_mtc_check_TP_MW_ECSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 15
f_mtc_check_TP_GM_PCSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 20
// PRACK after 183 Session Progress: require field is present
// FIXME Add check of requires SIP message header to check PRACK
//f_mtc_check_TP_MW_ECSCF_PRACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 15
//f_mtc_check_TP_GM_PCSCF_PRACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 20
//Rx/Gx exchange after 183(SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_04(vc_vxlte_monitor_components.rx);// Event 16
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 17
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 18
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 19
f_mtc_check_TP_MM_PSAP_180RINGING_01(vc_vxlte_monitor_components.mwB_PSAP); // 180 Ringing – Event 22
f_mtc_check_TP_MW_IBCF_180RINGING_01(vc_vxlte_monitor_components.mwBE, -, v_sip); // Event 23
f_mtc_check_TP_MW_ECSCF_180RINGING_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 24
f_mtc_check_TP_GM_PCSCF_180RINGING_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 25
// PRACK after 180 Session Progress: require field is present
// FIXME Add check of requires SIP message header to check PRACK
// f_mtc_check_TP_MW_ECSCF_PRACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 15
// f_mtc_check_TP_GM_PCSCF_PRACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 20
f_mtc_userCheckRinging(v_psap);
f_mtc_userCheckPeerIsRinging(v_ueA);
f_mtc_userAnswerCall(v_psap);
f_mtc_check_TP_MM_PSAP_200OK_01(vc_vxlte_monitor_components.mwB_PSAP, -, v_sip); // 200 OK Event 26
f_mtc_check_TP_MW_IBCF_200OK(vc_vxlte_monitor_components.mwBE, -, v_sip); // Event 27
f_mtc_check_TP_MW_ECSCF_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 28
f_mtc_check_TP_GM_PCSCF_200OK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 29
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 30
f_mtc_check_TP_MW_ECSCF_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 31
f_mtc_check_TP_MW_IBCF_ACK_01(vc_vxlte_monitor_components.mwBE, -, v_sip); // Event 32
f_mtc_check_TP_MM_PSAP_ACK_01(vc_vxlte_monitor_components.mwB_PSAP); // ACK – Event 33
f_mtc_userCheckCallEstablished(v_ueA); // Event 34
f_mtc_userCheckCallEstablished(v_psap); // Event 34
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_INI_01_02
group f_TD_VoLTE_ECO_INT_INI_01_02 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_01_02() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_01_02
} // End of group f_TD_VoLTE_ECO_INT_INI_01_02
/**
* @desc To demonstrate the establishment of dedicated bearers at the originating EPC due to SIP emergency session establishment.
* On successful emergency call setup with UE-A attached to EPC A, the P-CSCF should derive from the SDP offer and answer, descriptions of the Service Data Flow
* @see ETSI TS 103 795-2 Clause 5.3.1.2 UE calling PSAP with emergency registration
* @remark This is option3: IBCF is connected to the PSTN network
*/
testcase TD_VoLTE_ECO_INT_INI_01_03() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_EB_INTERFACENAME, // E-CSCF -> IBCF
PX_SIP_PSTN_INTERFACENAME // IBCF -> PSTN -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_userRegistration(v_ueA, v_userInfoA);
// PSAP is not known from the IMS A
f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_01_03();
// Test body
// TODO
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_INI_01_03
group f_TD_VoLTE_ECO_INT_INI_01_03 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_01_03() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_01_03
} // End of group f_TD_VoLTE_ECO_INT_INI_01_03
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
/**
* @desc To demonstrate the establishment of dedicated bearers at the originating EPC due to SIP emergency session session establishment within non-emergency registration.
* On successful call setup, the P-CSCF should derive from the SDP offer and answer, descriptions of the Service Data Flow. These are pushed towards PCRF and EPC as request for creation of adequate bearers
* @see ETSI TS 103 795-2 Clause 5.3.1.3 UE calling PSAP with non-emergency registration
* @remark This is option2: IBCF is connected to the PSAP, the interface IBCF and the PSAP is the Mm interface
*/
testcase TD_VoLTE_ECO_INT_INI_02() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_EB_INTERFACENAME, // E-CSCF -> IBCF
PX_SIP_MM_PSAP_INTERFACENAME // IBCF -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_userRegistration(v_ueA, v_userInfoA);
f_mtc_userRegistration(v_psap, v_infoPsap);
f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_02();
// Test body
//f_mtc_userInitiateCall (v_ueA, v_userTelInfoB);
f_mtc_check_TP_GM_PCSCF_INVITE_01(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 1
f_mtc_check_TP_GM_PCSCF_100Trying_01(vc_vxlte_monitor_components.gmA, -, v_sip);
//Rx/Gx exchange after INVITE (SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_03(vc_vxlte_monitor_components.rx);// Event 2
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 3
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 4
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 5
f_mtc_check_TP_RX_PCSCF_RAA_01(vc_vxlte_monitor_components.rx);// Events 7,8
f_mtc_check_TP_GX_PCRF_CCA_01(vc_vxlte_monitor_components.gx); // Events 6,9
f_mtc_check_TP_MW_ECSCF_INVITE_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 10
f_mtc_check_TP_MW_ECSCF_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
f_mtc_check_TP_MW_IBCF_INVITE_01(vc_vxlte_monitor_components.mwBE, -, v_sip); // Event 11
f_mtc_check_TP_MW_IBCF_100Trying_01(vc_vxlte_monitor_components.mwBE, -, v_sip);
f_mtc_check_TP_MM_PSAP_INVITE_01(vc_vxlte_monitor_components.mwB_PSAP, true); // Event 12
f_mtc_check_TP_MM_PSAP_100Trying_01(vc_vxlte_monitor_components.mwB_PSAP, -, v_sip);
// 183 Session Progress
f_mtc_check_TP_MM_PSAP_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwB_PSAP, -, v_sip); // Event 13
f_mtc_check_TP_MW_IBCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwBE, -, v_sip); // Event 14
f_mtc_check_TP_MW_ECSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 15
f_mtc_check_TP_GM_PCSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 20
// PRACK after 183 Session Progress: require field is present
// FIXME Add check of requires SIP message header to check PRACK
//f_mtc_check_TP_MW_ECSCF_PRACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 15
//f_mtc_check_TP_GM_PCSCF_PRACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 20
//Rx/Gx exchange after 183(SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_04(vc_vxlte_monitor_components.rx);// Event 16
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 17
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 18
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 19
f_mtc_check_TP_MM_PSAP_180RINGING_01(vc_vxlte_monitor_components.mwB_PSAP); // 180 Ringing – Event 22
f_mtc_check_TP_MW_IBCF_180RINGING_01(vc_vxlte_monitor_components.mwBE, -, v_sip); // Event 23
f_mtc_check_TP_MW_ECSCF_180RINGING_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 24
f_mtc_check_TP_GM_PCSCF_180RINGING_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 25
// PRACK after 180 Session Progress: require field is present
// FIXME Add check of requires SIP message header to check PRACK
// f_mtc_check_TP_MW_ECSCF_PRACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 15
// f_mtc_check_TP_GM_PCSCF_PRACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 20
f_mtc_userCheckRinging(v_psap);
f_mtc_userCheckPeerIsRinging(v_ueA);
f_mtc_userAnswerCall(v_psap);
f_mtc_check_TP_MM_PSAP_200OK_01(vc_vxlte_monitor_components.mwB_PSAP, -, v_sip); // 200 OK Event 26
f_mtc_check_TP_MW_IBCF_200OK(vc_vxlte_monitor_components.mwBE, -, v_sip); // Event 27
f_mtc_check_TP_MW_ECSCF_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 28
f_mtc_check_TP_GM_PCSCF_200OK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 29
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 30
f_mtc_check_TP_MW_ECSCF_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 31
f_mtc_check_TP_MW_IBCF_ACK_01(vc_vxlte_monitor_components.mwBE, -, v_sip); // Event 32
f_mtc_check_TP_MM_PSAP_ACK_01(vc_vxlte_monitor_components.mwB_PSAP); // ACK – Event 33
f_mtc_userCheckCallEstablished(v_ueA); // Event 34
f_mtc_userCheckCallEstablished(v_psap); // Event 34
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_INI_02
group f_TD_VoLTE_ECO_INT_INI_02 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_02() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_02
} // End of group f_TD_VoLTE_ECO_INT_INI_02
/**
* @desc To demonstrate the establishment of emergency bearers at the originating EPC due to SIP emergency session establishment withinout registration.
* On successful emergency call setup with UE-A attached to EPC A but not attached to IMS A, the P-CSCF should derive from the SDP offer and answer, descriptions of the Service Data Flow
* @see ETSI TS 103 795-2 Clause 5.3.1.3 UE calling PSAP without registration
* @remark This is option2: IBCF is connected to the PSAP, the interface IBCF and the PSAP is the Mm interface
*/
testcase TD_VoLTE_ECO_INT_INI_03() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_EB_INTERFACENAME, // E-CSCF -> IBCF
PX_SIP_MM_PSAP_INTERFACENAME // IBCF -> PSAP
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
// No registration for user A
f_mtc_userRegistration(v_psap, v_infoPsap);
f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_03();
// Test body
//f_mtc_userInitiateCall (v_ueA, v_userTelInfoB);
f_mtc_check_TP_GM_PCSCF_INVITE_01(vc_vxlte_monitor_components.gmA, -, v_sip); // INVITE Event 1
f_mtc_check_TP_GM_PCSCF_100Trying_01(vc_vxlte_monitor_components.gmA, -, v_sip);
//Rx/Gx exchange after INVITE (SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_03(vc_vxlte_monitor_components.rx);// Event 2
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 3
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 4
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 5
f_mtc_check_TP_RX_PCSCF_RAA_01(vc_vxlte_monitor_components.rx);// Events 7,8
f_mtc_check_TP_GX_PCRF_CCA_01(vc_vxlte_monitor_components.gx); // Events 6,9
f_mtc_check_TP_MW_ECSCF_INVITE_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 10
f_mtc_check_TP_MW_ECSCF_100Trying_01(vc_vxlte_monitor_components.mwPE, -, v_sip);
f_mtc_check_TP_MW_IBCF_INVITE_01(vc_vxlte_monitor_components.mwBE, -, v_sip); // Event 11
f_mtc_check_TP_MW_IBCF_100Trying_01(vc_vxlte_monitor_components.mwBE, -, v_sip);
f_mtc_check_TP_MM_PSAP_INVITE_01(vc_vxlte_monitor_components.mwB_PSAP, true); // Event 12
f_mtc_check_TP_MM_PSAP_100Trying_01(vc_vxlte_monitor_components.mwB_PSAP, -, v_sip);
// 183 Session Progress
f_mtc_check_TP_MM_PSAP_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwB_PSAP, -, v_sip); // Event 13
f_mtc_check_TP_MW_IBCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwBE, -, v_sip); // Event 14
f_mtc_check_TP_MW_ECSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 15
f_mtc_check_TP_GM_PCSCF_183SESSION_PROGRESS_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 20
// PRACK after 183 Session Progress: require field is present
// FIXME Add check of requires SIP message header to check PRACK
//f_mtc_check_TP_MW_ECSCF_PRACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 15
//f_mtc_check_TP_GM_PCSCF_PRACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 20
//Rx/Gx exchange after 183(SDP) was received at P-CSCF
f_mtc_check_TP_RX_PCSCF_AAR_04(vc_vxlte_monitor_components.rx);// Event 16
f_mtc_check_TP_GX_PCRF_RAR_01(vc_vxlte_monitor_components.gx, true); // Event 17
f_mtc_check_TP_GX_PGW_RAA_02(vc_vxlte_monitor_components.gx); // Event 18
f_mtc_check_TP_RX_PCRF_AAA_02(vc_vxlte_monitor_components.rx); // Event 19
f_mtc_check_TP_MM_PSAP_180RINGING_01(vc_vxlte_monitor_components.mwB_PSAP); // 180 Ringing – Event 22
f_mtc_check_TP_MW_IBCF_180RINGING_01(vc_vxlte_monitor_components.mwBE, -, v_sip); // Event 23
f_mtc_check_TP_MW_ECSCF_180RINGING_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 24
f_mtc_check_TP_GM_PCSCF_180RINGING_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 25
// PRACK after 180 Session Progress: require field is present
// FIXME Add check of requires SIP message header to check PRACK
// f_mtc_check_TP_MW_ECSCF_PRACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 15
// f_mtc_check_TP_GM_PCSCF_PRACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 20
f_mtc_userCheckRinging(v_psap);
f_mtc_userCheckPeerIsRinging(v_ueA);
f_mtc_userAnswerCall(v_psap);
f_mtc_check_TP_MM_PSAP_200OK_01(vc_vxlte_monitor_components.mwB_PSAP, -, v_sip); // 200 OK Event 26
f_mtc_check_TP_MW_IBCF_200OK(vc_vxlte_monitor_components.mwBE, -, v_sip); // Event 27
f_mtc_check_TP_MW_ECSCF_200OK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 28
f_mtc_check_TP_GM_PCSCF_200OK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 29
f_mtc_check_TP_GM_PCSCF_ACK_01(vc_vxlte_monitor_components.gmA, -, v_sip); // Event 30
f_mtc_check_TP_MW_ECSCF_ACK_01(vc_vxlte_monitor_components.mwPE, -, v_sip); // Event 31
f_mtc_check_TP_MW_IBCF_ACK_01(vc_vxlte_monitor_components.mwBE, -, v_sip); // Event 32
f_mtc_check_TP_MM_PSAP_ACK_01(vc_vxlte_monitor_components.mwB_PSAP); // ACK – Event 33
f_mtc_userCheckCallEstablished(v_ueA); // Event 34
f_mtc_userCheckCallEstablished(v_psap); // Event 34
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_INI_03
group f_TD_VoLTE_ECO_INT_INI_03 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_03() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_03
} // End of group f_TD_VoLTE_ECO_INT_INI_03
/**
* @desc TODO
* On successful emergency call setup with UE-A attached to EPC A, the P-CSCF should derive from the SDP offer and answer, descriptions of the Service Data Flow
* @see ETSI TS 103 795-2 Clause 5.3.1.4 Emergency session establishment with LRF involvement
* @remark This is option2: IBCF is connected to the PSAP, the interface IBCF and the PSAP is the Mm interface
*/
testcase TD_VoLTE_ECO_INT_INI_04() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_EB_INTERFACENAME, // E-CSCF -> IBCF
PX_SIP_MM_PSAP_INTERFACENAME, // IBCF -> PSAP
PX_SIP_ML_LRF_INTERFACENAME // E-CSCF -> LRF: mlE_LTF
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_userRegistration(v_ueA, v_userInfoA);
f_mtc_userRegistration(v_psap, v_infoPsap);
f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_04();
// Test body
//f_mtc_userInitiateCall (v_ueA, v_userTelInfoB);
// TODO
f_mtc_userCheckCallEstablished(v_ueA); // Event 34
f_mtc_userCheckCallEstablished(v_psap); // Event 34
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}
f_cf_adapter_down ( );
} // End of TC TD_VoLTE_ECO_INT_INI_04
group f_TD_VoLTE_ECO_INT_INI_04 {
function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_04() runs on ImsTestCoordinator {
log("If the test case fails, please check the preconditions");
// TODO Add real code to check pre-conditions
} // End of function f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_04
} // End of group f_TD_VoLTE_ECO_INT_INI_04
/**
* @desc To demonstrate that if an emergency call has been terminated, the attempt by the PSAP call taker to communicate back to the emergency caller shall be answered
* Verifying the functionality of the PSAP callback feature, ensuring that the callback is successfully initiated, routed and that media is correctly transmitted over the dedicated bearer. The callback must use the same media as the original emergency call
* @see ETSI TS 103 795-2 Clause 5.3.1.5 Callback from PSAP
* @remark This is option2: IBCF is connected to the PSAP, the interface IBCF and the PSAP is the Mm interface
*/
testcase TD_VoLTE_ECO_INT_INI_05() runs on ImsTestCoordinator system IotSystemInterface {
var IotEquipmentUser v_ueA := f_cf_create_IotEquipmentUser ( c_userUE_A_emergency );
var IotEquipmentUser v_psap := f_cf_create_IotEquipmentUser ( c_psap );
var ImsUserInfo v_userInfoA := f_getImUser ( PX_EUT_A_EMERGENCY );
var ImsUserInfo v_infoPsap := f_getImUser ( PX_PSAP );
f_setVxLteMonIterfacesAvailability();
//Check required monitor interfaces due to TD
if (f_checkVxLteRequiredMonitorInterface({PX_SIP_GMA_INTERFACENAME,
PX_DIAMETER_GX_INTERFACENAME,
PX_DIAMETER_RX_INTERFACENAME,
PX_SIP_MW_PE_INTERFACENAME,
PX_SIP_EB_INTERFACENAME, // E-CSCF -> IBCF
PX_SIP_MM_PSAP_INTERFACENAME
}))
{
var SipMessage v_sip;
f_cf_createVxLteMonitor();
// map/connect component ports
f_cf_adapter_up ( );
f_cf_user_up ( v_ueA );
f_cf_user_up ( v_psap );
f_cf_VxLteMonitor_Up();
// Preamble
f_mtc_userRegistration(v_ueA, v_userInfoA);
f_mtc_userRegistration(v_psap, v_infoPsap);
f_mtc_check_precond_TD_VoLTE_ECO_INT_INI_05();
// Test body
//f_mtc_userInitiateCall (v_ueA, v_userTelInfoB);
// TODO
f_mtc_userCheckCallEstablished(v_ueA); // Event 34
f_mtc_userCheckCallEstablished(v_psap); // Event 34
// Postamble
f_mtc_EndCall(v_ueA);
f_PO_user_home_deregistration(v_ueA);
f_PO_user_home_deregistration(v_psap);
//f_cf_int_call_down(v_config);
//unmap/disconnect component ports
f_cf_user_down ( v_psap );
f_cf_user_down ( v_ueA );
f_cf_VxLteMonitor_Down();
}else{
//log...
setverdict (inconc,"At least one required monitor interface SHALL be selected! Check PIXITs")
}