Newer
Older
* @version $URL$
* $Id$
* @desc This module provides test cases for S1AP tests.
* @copyright ETSI Copyright Notification
* No part may be reproduced except as authorized by written permission.
* The copyright and the foregoing restriction extend to reproduction in all media.
* All rights reserved.
* @see ETSI TS 136 413 / 3GPP TS 36.413 version 13.4.0 Release 13
//LibCommon
import from LibCommon_Sync all ;
import from LibCommon_VerdictControl all;
//LibS1AP
//import from LibS1AP_TypesAndValues all;
import from LibS1AP_Interface all;
//Ats
import from S1AP_TestConfiguration all;
import from S1AP_TestSystem all;
import from S1AP_TCFunctions all;
import from S1AP_Steps all;
import from S1AP_TestSystem all;
/**
* @desc E-RAB management group
* @see ETSI TS 103 497-2 Clause 5.2.2.1.2 E-RAB management group
*/
/**
* @desc Verify that the IUT can successfully process all mandatory IEs in an E-RAB_SETUP_REQUEST received
* due to E-RAB management procedure and send E-RAB_SETUP_RESPONSE with successfully established E-RABs
* included in the E-RAB_Setup_List IE.
* <pre>
* Pics Selection: PICS A.3/1.1
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of an E-RAB_SETUP_REQUEST
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-RAB_to_be_Setup_List
* containing an E-RAB_to_be_Setup Item 1
* containing an E-RAB_ID
* containing an E-RAB_Level_QoS_Parameters
* containing QCI
* indicating value 5
* containing a Transport_Layer_Address
* containing a GTP-TEID
* containing a NAS-PDU
* sends an E-RAB_SETUP_RESPONSE
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-RAB_Setup_List
* containing an E-RAB_Setup Item 1
* containing an E-RAB_ID
* containing a Transport_Layer_Address
* containing a GTP-TEID.
* </pre>
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_RAB_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.2.1.2(1st dashed line in 5th dashed list) and 9.1.3.1 and 9.1.3.2
*/
testcase TC_S1AP_eNB_RAB_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component configuration
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
/**
* @desc Verify that the IUT after receiving an E-RAB_SETUP_REQUEST with failed E-RAB sends an E-RAB_SETUP_RESPONSE
* with E-RAB_Failed_to_Setup_List.
* <pre>
* Pics Selection: PICS A.3/1.1
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of an E-RAB_SETUP_REQUEST
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-RAB_to_be_Setup_List
* containing an E-RAB_to_be_Setup Item 1
* containing an E-RAB_ID
* indicating value A
* containing an E-RAB_Level_QoS_Parameters
* containing a Transport_Layer_Address
* containing a GTP-TEID
* containing a NAS-PDU
* containing an E-RAB_to_be_Setup Item 2(not acceptable data for eNB)
* containing an E-RAB_ID
* indicating value B(different to value A)
* containing an E-RAB_Level_QoS_Parameters
* containing QCI
* indicating not supported QCI value(255)
* containing a Transport_Layer_Address
* containing a GTP-TEID
* containing a NAS-PDU
* sends an E-RAB_SETUP_RESPONSE
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-RAB_Setup_List
* containing an E-RAB_Setup Item 1
* containing an E-RAB_ID
* indicating value A
* containing a Transport_Layer_Address
* containing a GTP-TEID
* containing an E-RAB_Failed_to_Setup_List
* containing an E-RAB_List Item 1
* containing an E-RAB_ID
* indicating value B
* containing a Cause
* indicating ‘not-supported-QCI-value’.
* </pre>
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_RAB_02
* @reference ETSI TS 136 413 V13.4.0 Clause 8.2.1.2(2nd dashed line in 5th dashed list) and 9.1.3.1 and 9.1.3.2
*/
testcase TC_S1AP_eNB_RAB_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component configuration
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
* @desc Management group
* @see ETSI TS 103 497-2 Clause 5.2.2.1.6 NAS transport group
*/
group NAS_transport_group {
/**
* @desc Verify that the IUT can send an INITIAL_UE_MESSAGE to indicate the initiation of a NAS Transport procedure.
* <pre>
* Pics Selection: PICS A.3/5.1
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate the initiation of a NAS Transport procedure
* sends an INITIAL_UE_MESSAGE
* containing an eNB_UE_S1AP_ID
* containing a NAS-PDU
* containg a TAI
* containing a PLMN_Identity
* containing a TAC
* containing an E-UTRAN_CGI
* containing a PLMN_Identity
* containing a Cell_Identity
* containing a RRC_Establishment_Cause.
* </pre>
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_NAS_01
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
* @reference ETSI TS 136 413 V13.4.0 Clause 8.6.2.1¶1 and 9.1.7.1
*/
testcase TC_S1AP_eNB_NAS_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_NAS_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_NAS_01
/**
* @desc Verify that the IUT can send an UPLINK_NAS_TRANSPORT to indicate an ongoing NAS Transport procedure.
* <pre>
* Pics Selection: PICS A.3/5.3
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an ongoing NAS Transport procedure
* sends an UPLINK_NAS_TRANSPORT
* containing an MME UE S1AP ID
* containing an eNB_UE_S1AP_ID
* containing a NAS-PDU
* containg a TAI
* containing a PLMN_Identity
* containing a TAC
* containing an E-UTRAN_CGI
* containing a PLMN_Identity
* containing a Cell_Identity
* containing a RRC_Establishment_Cause.
* </pre>
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_NAS_02
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
* @reference ETSI TS 136 413 V13.4.0 Clause 8.6.2.3¶1 and 9.1.7.3
*/
testcase TC_S1AP_eNB_NAS_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_NAS_02());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_NAS_02
/**
* @desc Verify that the IUT can send a NAS_NON_DELIVERY_INDICATION to indicate the eNB was unable to ensure that the message has been received by the UE.
* <pre>
* Pics Selection: PICS A.3/5.4
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a UE has not received a INITIAL_UE_MESSAGE
* sends a NAS_NON_DELIVERY_INDICATION
* containing an MME UE S1AP ID
* containing an eNB_UE_S1AP_ID
* containing a NAS-PDU
* containing a Cause
* indicating an appropriate cause value.
* </pre>
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_NAS_03
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
* @reference ETSI TS 136 413 V13.4.0 Clause 8.6.2.4 and 9.1.7.4
*/
testcase TC_S1AP_eNB_NAS_03() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_NAS_03());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_NAS_03
} // End of group group NAS_transport_group
* @desc Management group
* @see ETSI TS 103 497-2 Clause 5.2.2.1.7 Management group
*/
group Management_group {
/**
* @desc Verify that the IUT can successfully process all mandatory IEs in a RESET and sends a RESET_ACKNOWLEDGE due to a Reset procedure initiated from the MME.
* <pre>
* Pics Selection: PICS A.3/6.1.2
* Ensure that the IUT
* on receipt of a RESET
* containing a Cause
* indicating an appropriate cause value
* containing a Reset_Type
* containing a S1_Interface
* indicating a value ‘Reset_all’
* sends a RESET_ACKNOWLEDGE
* containing a UE-associated_logical_S1-connection_list.
* </pre>
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_MNP_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.1.2.1¶2 and 9.1.8.1 and 9.1.8.2
*/
testcase TC_S1AP_eNB_MNP_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
/**
* @desc Verify that the IUT can send an RESET due to a Reset procedure initiated from the E-UTRAN.
* <pre>
* Pics Selection: PICS A.3/6.1.2
* Ensure that the IUT
* to indicate a Reset procedure initiated from the E-UTRAN
* containing a Cause
* indicating an appropriate cause value
* containing a Reset_Type
* containing a S1_Interface
* indicating a value ‘Reset_all’.
* </pre>
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_MNP_02
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.1.2.2¶1 and 9.1.8.1 and 9.1.8.2
*/
testcase TC_S1AP_eNB_MNP_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
/**
* @desc Verify that the IUT can successfully manage Reset procedure in case of Abnormal Condition at the E-UTRAN.
* <pre>
* Pics Selection: PICS A.3/6.1.1
* Ensure that the IUT
* on receipt of a RESET
* containing a Cause
* indicating an appropriate cause value
* containing a Reset_Type
* containing a Part_of_S1_interface
* indicating one empty ‘UE-associated_logical_S1-connection’
* sends a RESET_ACKNOWLEDGE
* containing a UE-associated_logical_S1-connection_list.
* </pre>
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_MNP_03
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.1.2.2¶1 and 9.1.8.1 and 9.1.8.2
*/
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
testcase TC_S1AP_eNB_MNP_03() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_MNP_03());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_MNP_03
/**
* @desc Verify that the IUT can send an ERROR_INDICATION due to an Error Indication procedure.
* <pre>
* Pics Selection: PICS A.3/6.2.2
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an Error Indication procedure
* sends an ERROR_INDICATION
* (containing a Cause
* or containing a Criticality_Diagnostics).
* </pre>
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_MNP_04
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.2.2 and 9.1.8.3
*/
testcase TC_S1AP_eNB_MNP_04() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_MNP_04());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_MNP_04
/**
* @desc Verify that the IUT can send a S1_SETUP_REQUEST to indicate a S1 Setup procedure.
* <pre>
* Pics Selection: PICS A.3/6.3
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a S1 Setup procedure
* sends a S1_SETUP_REQUEST
* containing a Global_eNB_ID
* containing a Supported_TAs
* containing a TAC
* containing a Default_Paging_DRX.
* </pre>
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_MNP_05
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.3.2¶1 and 9.1.8.4 and 9.1.8.5
*/
testcase TC_S1AP_eNB_MNP_05() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
/**
* @desc Verify that the IUT can send an ENB_CONFIGURATION_UPDATE to indicate an eNB Configuration Update procedure.
* <pre>
* Pics Selection: PICS A.3/6.4
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an eNB Configuration Update procedure
* sends an ENB_CONFIGURATION_UPDATE
* containing a Global_eNB_ID
* containing a Supported_TAs
* containing a TAC.
* </pre>
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_MNP_06
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.4.2¶1 and 9.1.8.7 and 9.1.8.8
*/
testcase TC_S1AP_eNB_MNP_06() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_MNP_06());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_MNP_06
/**
* @desc Verify that the IUT can successfully process all mandatory IEs in an MME_CONFIGURATION_UPDATE and
* sends an MME_CONFIGURATION_UPDATE_ACKNOWLEDGE due to an MME Configuration Update procedure.
* <pre>
* Pics Selection: PICS A.3/6.5
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of an MME_CONFIGURATION_UPDATE
* may containing a Served_GUMMEIs
* may containing a Served_PLMNs
* sends an MME_CONFIGURATION_UPDATE_ACKNOWLEDGE.
* </pre>
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_MNP_07
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.5.2¶1 and 9.1.8.10 and 9.1.8.11
*/
testcase TC_S1AP_eNB_MNP_07() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_MNP_07());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_MNP_07
/**
* @desc Verify that the IUT can successfully process all mandatory IEs in an MME_CONFIGURATION_UPDATE and
* sends an MME CONFIGURATION UPDATE_FAILURE due to an invalid MME Configuration Update procedure.
* <pre>
* Pics Selection: PICS A.3/6.5
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of an MME_CONFIGURATION_UPDATE
* containing a Broadcast_PLMNs
* indicating at least one unknown PLMN identity
* sends an MME_CONFIGURATION_UPDATE_FAILURE
* containing a Cause
* indicating an appropriate cause value.
* </pre>
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_MNP_08
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.5.3 and 9.1.8.10 and 9.1.8.12
*/
testcase TC_S1AP_eNB_MNP_08() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_MNP_08());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_MNP_08
} // End of group Management_group
/**
* @desc S1 CDMA 2000 tunnelling group
* @see ETSI TS 103 497-2 Clause 5.2.2.1.8 S1 CDMA 2000 tunnelling group group
*/
group S1_CDMA_2000_tunelling_group {
/**
* @desc Verify that the IUT can send a DOWNLINK_S1_CDMA2000_TUNNELLING.
* <pre>
* Pics Selection: PICS A.3/7.2
* Ensure that the IUT
* to indicate a CDMA2000 to be forwarded
* sends an UPLINK_S1_CDMA2000_TUNNELLING
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a CDMA2000_RAT_Type
* containing a CDMA2000_Sector_ID
* containing a CDMA2000_PDU.
* </pre>
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_STP_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.8.2.2¶1 and 9.1.9.2 and 9.2.1.23
*/
testcase TC_S1AP_eNB_STP_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of group S1_CDMA_2000_tunelling_group
/**
* @desc UE capability info indication group
* @see ETSI TS 103 497-2 Clause 5.2.2.1.9 UE capability info indication group
*/
group UE_capability_info_indication_group {
/**
* @desc Verify that the IUT can send a UE_CAPABILITY_INFO_INDICATION to indicate capability-related information update.
* <pre>
* Pics Selection: PICS A.3/8
* Ensure that the IUT
* to indicate a capability-related information update
* sends an UE_CAPABILITY_INFO_INDICATION
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a containing a UE_Radio_Capability.
* </pre>
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_UEC_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.9.2 and 9.1.10
*/
testcase TC_S1AP_eNB_UEC_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of group UE_capability_info_indication_group
/**
* @desc Trace Procedures group
* @see ETSI TS 103 497-2 Clause 5.2.2.1.10 Trace group
*/
group Trace_group {
/**
* @desc Verify that the IUT can successfully send a TRACE_FAILURE_INDICATION on TRACE_START.
* <pre>
* Pics Selection: PICS A.3/9.1 and A.3/9.2
* Ensure that the IUT
* on receipt of a TRACE_START
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Trace_Activation
* containing an E-UTRAN_Trace_ID
* containing a Interfaces_To_Trace
* indicating value ‘S1-MME’
* containing a Trace_depth
* indicating value ‘maximum’
* containing a Trace_Collection_Entity_IP_Address
* not containing an MDT_Configuration
* sends TRACE_FAILURE_INDICATION
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-UTRAN_Trace_ID
* containing a Cause
* indicating an appropriate cause value.
* </pre>
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_TRP_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.10.1.2-8 and 8.10.2.2 and 9.1.11.1 and 9.1.11.2
*/
testcase TC_S1AP_eNB_TRP_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
/**
* @desc Verify that the IUT can successfully send a TRACE_FAILURE_INDICATION on DEACTIVATE_TRACE.
* <pre>
* Pics Selection: PICS A.3/9.1 and A.3/9.2
* Ensure that the IUT
* on receipt of a DEACTIVATE_TRACE
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Trace_Activation
* containing an E-UTRAN_Trace_ID
* sends TRACE_FAILURE_INDICATION
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-UTRAN_Trace_ID
* containing a Cause
* indicating an appropriate cause value.
* </pre>
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_TRP_02
* @reference ETSI TS 136 413 V13.4.0 Clause 8.10.3.2-3 and 8.10.2.2 and 9.1.11.3 and 9.1.11.2
testcase TC_S1AP_eNB_TRP_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
/**
* @desc Verify that the IUT can send a CELL_TRAFFIC_TRACE when the conditions required for tracing are met.
* <pre>
* Pics Selection: PICS A.3/9.4
* Ensure that the IUT
* to indicate the conditions required for tracing are met
* sends CELL_TRAFFIC_TRACE
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-UTRAN_Trace_ID
* containing an E-UTRAN_CGI
* containing a PLMN_Identity
* containing a Cell_Identity
* containing a Trace_Collection_Entity_IP_Address.
* </pre>
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_TRP_03
* @reference ETSI TS 136 413 V13.4.0 Clause 8.10.4.2 and 9.1.18
*/
testcase TC_S1AP_eNB_TRP_03() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
* @desc Location Reporting Procedures group
* @see ETSI TS 103 497-2 Clause 5.2.2.1.11 Location reporting group
* @desc Verify that the IUT can process all mandatory IEs in a LOCATION_REPORTING_CONTROL containing Event Type IE indicating Directly and sends a LOCATION_REPORT.
* Ensure that the IUT
* on receipt of a LOCATION_REPORTING_CONTROL
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Request_Type
* containing an Event_Type
* indicating Directly
* containing a Report_Area
* indicating ECGI
* sends LOCATION_REPORT
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-UTRAN_CGI
* containing a PLMN_Identity
* containing a Cell_Identity
* containing a TAI
* containing a PLMN_Identity
* containing a TAC
* containing a Request_Type
* containing a Event_Type
* containing a Report_Area.
* </pre>
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_LRP_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.11.1.2-2(1st dashed line) and 9.1.12.1 and 9.1.12.3 and 9.2.1.16,34,38
*/
testcase TC_S1AP_eNB_LRP_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
* @desc Verify that the IUT can process all mandatory IEs in a LOCATION_REPORTING_CONTROL containing Event Type IE indicating Change of service cell and sends a LOCATION_REPORT.
* Ensure that the IUT
* on receipt of a LOCATION_REPORTING_CONTROL
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Request_Type
* containing an Event_Type
* indicating change_of_service_cell
* containing a Report_Area
* indicating ECGI
* when UE changes to new cell
* sends LOCATION_REPORT
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-UTRAN_CGI
* containing a PLMN_Identity
* containing a Cell_Identity
* containing a TAI
* containing a PLMN_Identity
* containing a TAC
* containing a Request_Type
* containing a Event_Type
* containing a Report_Area.
* </pre>
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_LRP_02
* @reference ETSI TS 136 413 V13.4.0 Clause 8.11.1.2-2(1st dashed line) and 9.1.12.1 and 9.1.12.3 and 9.2.1.16,34,38
*/
testcase TC_S1AP_eNB_LRP_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
* @desc Verify that the IUT can process all mandatory IEs in a LOCATION_REPORTING_CONTROL containing Event Type IE indicating Stop change of service cell and sends a LOCATION_REPORT.