/**
* @author ETSI / STF519
* @version $URL$
* $Id$
* @desc This module provides test cases for S1AP tests.
* @copyright ETSI Copyright Notification
* No part may be reproduced except as authorized by written permission.
* The copyright and the foregoing restriction extend to reproduction in all media.
* All rights reserved.
* @see ETSI TS 136 413 / 3GPP TS 36.413 version 13.4.0 Release 13
*/
module S1AP_TestCases {
//LibCommon
import from LibCommon_Sync all ;
import from LibCommon_VerdictControl all;
//LibS1AP
//import from LibS1AP_TypesAndValues all;
import from LibS1AP_Interface all;
import from LibS1AP_Steps all;
//Ats
import from S1AP_TestConfiguration all;
import from S1AP_TestSystem all;
import from S1AP_TCFunctions all;
import from S1AP_Pics all;
import from S1AP_Pixits all;
import from S1AP_Steps all;
import from S1AP_TestSystem all;
group eNB_Role {
/**
* @desc E-RAB management group
* @see ETSI TS 103 497-2 Clause 5.2.2.1.2 E-RAB management group
*/
group ERAB_management_group {
/**
* @desc Verify that the IUT can successfully process all mandatory IEs in an E-RAB_SETUP_REQUEST received
* due to E-RAB management procedure and send E-RAB_SETUP_RESPONSE with successfully established E-RABs
* included in the E-RAB_Setup_List IE.
*
* Pics Selection: PICS A.3/1.1
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of an E-RAB_SETUP_REQUEST
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-RAB_to_be_Setup_List
* containing an E-RAB_to_be_Setup Item 1
* containing an E-RAB_ID
* containing an E-RAB_Level_QoS_Parameters
* containing QCI
* indicating value 5
* containing a Transport_Layer_Address
* containing a GTP-TEID
* containing a NAS-PDU
* sends an E-RAB_SETUP_RESPONSE
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-RAB_Setup_List
* containing an E-RAB_Setup Item 1
* containing an E-RAB_ID
* containing a Transport_Layer_Address
* containing a GTP-TEID.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_RAB_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.2.1.2(1st dashed line in 5th dashed list) and 9.1.3.1 and 9.1.3.2
*/
testcase TC_S1AP_eNB_RAB_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component configuration
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_RAB_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_RAB_01
/**
* @desc Verify that the IUT after receiving an E-RAB_SETUP_REQUEST with failed E-RAB sends an E-RAB_SETUP_RESPONSE
* with E-RAB_Failed_to_Setup_List.
*
* Pics Selection: PICS A.3/1.1
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of an E-RAB_SETUP_REQUEST
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-RAB_to_be_Setup_List
* containing an E-RAB_to_be_Setup Item 1
* containing an E-RAB_ID
* indicating value A
* containing an E-RAB_Level_QoS_Parameters
* containing a Transport_Layer_Address
* containing a GTP-TEID
* containing a NAS-PDU
* containing an E-RAB_to_be_Setup Item 2(not acceptable data for eNB)
* containing an E-RAB_ID
* indicating value B(different to value A)
* containing an E-RAB_Level_QoS_Parameters
* containing QCI
* indicating not supported QCI value(255)
* containing a Transport_Layer_Address
* containing a GTP-TEID
* containing a NAS-PDU
* sends an E-RAB_SETUP_RESPONSE
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-RAB_Setup_List
* containing an E-RAB_Setup Item 1
* containing an E-RAB_ID
* indicating value A
* containing a Transport_Layer_Address
* containing a GTP-TEID
* containing an E-RAB_Failed_to_Setup_List
* containing an E-RAB_List Item 1
* containing an E-RAB_ID
* indicating value B
* containing a Cause
* indicating ‘not-supported-QCI-value’.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_RAB_02
* @reference ETSI TS 136 413 V13.4.0 Clause 8.2.1.2(2nd dashed line in 5th dashed list) and 9.1.3.1 and 9.1.3.2
*/
testcase TC_S1AP_eNB_RAB_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component configuration
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_RAB_02());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_RAB_02
} // End of group E-RAB_management_group
/**
* @desc Management group
* @see ETSI TS 103 497-2 Clause 5.2.2.1.6 NAS transport group
*/
group NAS_transport_group {
/**
* @desc Verify that the IUT can send an INITIAL_UE_MESSAGE to indicate the initiation of a NAS Transport procedure.
*
* Pics Selection: PICS A.3/5.1
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate the initiation of a NAS Transport procedure
* sends an INITIAL_UE_MESSAGE
* containing an eNB_UE_S1AP_ID
* containing a NAS-PDU
* containg a TAI
* containing a PLMN_Identity
* containing a TAC
* containing an E-UTRAN_CGI
* containing a PLMN_Identity
* containing a Cell_Identity
* containing a RRC_Establishment_Cause.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_NAS_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.6.2.1¶1 and 9.1.7.1
*/
testcase TC_S1AP_eNB_NAS_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_NAS_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_NAS_01
/**
* @desc Verify that the IUT can send an UPLINK_NAS_TRANSPORT to indicate an ongoing NAS Transport procedure.
*
* Pics Selection: PICS A.3/5.3
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an ongoing NAS Transport procedure
* sends an UPLINK_NAS_TRANSPORT
* containing an MME UE S1AP ID
* containing an eNB_UE_S1AP_ID
* containing a NAS-PDU
* containg a TAI
* containing a PLMN_Identity
* containing a TAC
* containing an E-UTRAN_CGI
* containing a PLMN_Identity
* containing a Cell_Identity
* containing a RRC_Establishment_Cause.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_NAS_02
* @reference ETSI TS 136 413 V13.4.0 Clause 8.6.2.3¶1 and 9.1.7.3
*/
testcase TC_S1AP_eNB_NAS_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_NAS_02());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_NAS_02
/**
* @desc Verify that the IUT can send a NAS_NON_DELIVERY_INDICATION to indicate the eNB was unable to ensure that the message has been received by the UE.
*
* Pics Selection: PICS A.3/5.4
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a UE has not received a INITIAL_UE_MESSAGE
* sends a NAS_NON_DELIVERY_INDICATION
* containing an MME UE S1AP ID
* containing an eNB_UE_S1AP_ID
* containing a NAS-PDU
* containing a Cause
* indicating an appropriate cause value.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_NAS_03
* @reference ETSI TS 136 413 V13.4.0 Clause 8.6.2.4 and 9.1.7.4
*/
testcase TC_S1AP_eNB_NAS_03() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_NAS_03());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_NAS_03
} // End of group group NAS_transport_group
/**
* @desc Management group
* @see ETSI TS 103 497-2 Clause 5.2.2.1.7 Management group
*/
group Management_group {
/**
* @desc Verify that the IUT can successfully process all mandatory IEs in a RESET and sends a RESET_ACKNOWLEDGE due to a Reset procedure initiated from the MME.
*
* Pics Selection: PICS A.3/6.1.2
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of a RESET
* containing a Cause
* indicating an appropriate cause value
* containing a Reset_Type
* containing a S1_Interface
* indicating a value ‘Reset_all’
* sends a RESET_ACKNOWLEDGE
* containing a UE-associated_logical_S1-connection_list.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_MNP_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.1.2.1¶2 and 9.1.8.1 and 9.1.8.2
*/
testcase TC_S1AP_eNB_MNP_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_MNP_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_MNP_01
/**
* @desc Verify that the IUT can send an RESET due to a Reset procedure initiated from the E-UTRAN.
*
* Pics Selection: PICS A.3/6.1.2
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a Reset procedure initiated from the E-UTRAN
* sends a RESET
* containing a Cause
* indicating an appropriate cause value
* containing a Reset_Type
* containing a S1_Interface
* indicating a value ‘Reset_all’.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_MNP_02
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.1.2.2¶1 and 9.1.8.1 and 9.1.8.2
*/
testcase TC_S1AP_eNB_MNP_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_MNP_02());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_MNP_02
/**
* @desc Verify that the IUT can successfully manage Reset procedure in case of Abnormal Condition at the E-UTRAN.
*
* Pics Selection: PICS A.3/6.1.1
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of a RESET
* containing a Cause
* indicating an appropriate cause value
* containing a Reset_Type
* containing a Part_of_S1_interface
* indicating one empty ‘UE-associated_logical_S1-connection’
* sends a RESET_ACKNOWLEDGE
* containing a UE-associated_logical_S1-connection_list.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_MNP_03
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.1.2.2¶1 and 9.1.8.1 and 9.1.8.2
*/
testcase TC_S1AP_eNB_MNP_03() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_MNP_03());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_MNP_03
/**
* @desc Verify that the IUT can send an ERROR_INDICATION due to an Error Indication procedure.
*
* Pics Selection: PICS A.3/6.2.2
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an Error Indication procedure
* sends an ERROR_INDICATION
* (containing a Cause
* or containing a Criticality_Diagnostics).
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_MNP_04
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.2.2 and 9.1.8.3
*/
testcase TC_S1AP_eNB_MNP_04() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_MNP_04());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_MNP_04
/**
* @desc Verify that the IUT can send a S1_SETUP_REQUEST to indicate a S1 Setup procedure.
*
* Pics Selection: PICS A.3/6.3
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a S1 Setup procedure
* sends a S1_SETUP_REQUEST
* containing a Global_eNB_ID
* containing a Supported_TAs
* containing a TAC
* containing a Default_Paging_DRX.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_MNP_05
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.3.2¶1 and 9.1.8.4 and 9.1.8.5
*/
testcase TC_S1AP_eNB_MNP_05() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_MNP_05());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_MNP_05
/**
* @desc Verify that the IUT can send an ENB_CONFIGURATION_UPDATE to indicate an eNB Configuration Update procedure.
*
* Pics Selection: PICS A.3/6.4
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an eNB Configuration Update procedure
* sends an ENB_CONFIGURATION_UPDATE
* containing a Global_eNB_ID
* containing a Supported_TAs
* containing a TAC.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_MNP_06
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.4.2¶1 and 9.1.8.7 and 9.1.8.8
*/
testcase TC_S1AP_eNB_MNP_06() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_MNP_06());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_MNP_06
/**
* @desc Verify that the IUT can successfully process all mandatory IEs in an MME_CONFIGURATION_UPDATE and
* sends an MME_CONFIGURATION_UPDATE_ACKNOWLEDGE due to an MME Configuration Update procedure.
*
* Pics Selection: PICS A.3/6.5
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of an MME_CONFIGURATION_UPDATE
* may containing a Served_GUMMEIs
* may containing a Served_PLMNs
* sends an MME_CONFIGURATION_UPDATE_ACKNOWLEDGE.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_MNP_07
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.5.2¶1 and 9.1.8.10 and 9.1.8.11
*/
testcase TC_S1AP_eNB_MNP_07() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_MNP_07());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_MNP_07
/**
* @desc Verify that the IUT can successfully process all mandatory IEs in an MME_CONFIGURATION_UPDATE and
* sends an MME CONFIGURATION UPDATE_FAILURE due to an invalid MME Configuration Update procedure.
*
* Pics Selection: PICS A.3/6.5
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of an MME_CONFIGURATION_UPDATE
* containing a Broadcast_PLMNs
* indicating at least one unknown PLMN identity
* sends an MME_CONFIGURATION_UPDATE_FAILURE
* containing a Cause
* indicating an appropriate cause value.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_MNP_08
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.5.3 and 9.1.8.10 and 9.1.8.12
*/
testcase TC_S1AP_eNB_MNP_08() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_MNP_08());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_MNP_08
} // End of group Management_group
/**
* @desc S1 CDMA 2000 tunnelling group
* @see ETSI TS 103 497-2 Clause 5.2.2.1.8 S1 CDMA 2000 tunnelling group group
*/
group S1_CDMA_2000_tunelling_group {
/**
* @desc Verify that the IUT can send a DOWNLINK_S1_CDMA2000_TUNNELLING.
*
* Pics Selection: PICS A.3/7.2
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a CDMA2000 to be forwarded
* sends an UPLINK_S1_CDMA2000_TUNNELLING
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a CDMA2000_RAT_Type
* containing a CDMA2000_Sector_ID
* containing a CDMA2000_PDU.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_STP_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.8.2.2¶1 and 9.1.9.2 and 9.2.1.23
*/
testcase TC_S1AP_eNB_STP_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_STP_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_STP_01
} // End of group S1_CDMA_2000_tunelling_group
/**
* @desc UE capability info indication group
* @see ETSI TS 103 497-2 Clause 5.2.2.1.9 UE capability info indication group
*/
group UE_capability_info_indication_group {
/**
* @desc Verify that the IUT can send a UE_CAPABILITY_INFO_INDICATION to indicate capability-related information update.
*
* Pics Selection: PICS A.3/8
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a capability-related information update
* sends an UE_CAPABILITY_INFO_INDICATION
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a containing a UE_Radio_Capability.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_UEC_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.9.2 and 9.1.10
*/
testcase TC_S1AP_eNB_UEC_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_UEC_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_UEC_01
} // End of group UE_capability_info_indication_group
/**
* @desc Trace Procedures group
* @see ETSI TS 103 497-2 Clause 5.2.2.1.10 Trace group
*/
group Trace_group {
/**
* @desc Verify that the IUT can successfully send a TRACE_FAILURE_INDICATION on TRACE_START.
*
* Pics Selection: PICS A.3/9.1 and A.3/9.2
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of a TRACE_START
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Trace_Activation
* containing an E-UTRAN_Trace_ID
* containing a Interfaces_To_Trace
* indicating value ‘S1-MME’
* containing a Trace_depth
* indicating value ‘maximum’
* containing a Trace_Collection_Entity_IP_Address
* not containing an MDT_Configuration
* sends TRACE_FAILURE_INDICATION
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-UTRAN_Trace_ID
* containing a Cause
* indicating an appropriate cause value.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_TRP_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.10.1.2-8 and 8.10.2.2 and 9.1.11.1 and 9.1.11.2
*/
testcase TC_S1AP_eNB_TRP_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_TRP_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_TRP_01
/**
* @desc Verify that the IUT can successfully send a TRACE_FAILURE_INDICATION on DEACTIVATE_TRACE.
*
* Pics Selection: PICS A.3/9.1 and A.3/9.2
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of a DEACTIVATE_TRACE
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Trace_Activation
* containing an E-UTRAN_Trace_ID
* sends TRACE_FAILURE_INDICATION
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-UTRAN_Trace_ID
* containing a Cause
* indicating an appropriate cause value.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_TRP_02
* @reference ETSI TS 136 413 V13.4.0 Clause 8.10.3.2-3 and 8.10.2.2 and 9.1.11.3 and 9.1.11.2
*/
testcase TC_S1AP_eNB_TRP_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_TRP_02());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_TRP_02
/**
* @desc Verify that the IUT can send a CELL_TRAFFIC_TRACE when the conditions required for tracing are met.
*
* Pics Selection: PICS A.3/9.4
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate the conditions required for tracing are met
* sends CELL_TRAFFIC_TRACE
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-UTRAN_Trace_ID
* containing an E-UTRAN_CGI
* containing a PLMN_Identity
* containing a Cell_Identity
* containing a Trace_Collection_Entity_IP_Address.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_TRP_03
* @reference ETSI TS 136 413 V13.4.0 Clause 8.10.4.2 and 9.1.18
*/
testcase TC_S1AP_eNB_TRP_03() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_TRP_03());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_TRP_03
} // End of group Trace_group
/**
* @desc Location Reporting Procedures group
* @see ETSI TS 103 497-2 Clause 5.2.2.1.11 Location reporting group
*/
group Location_reporting_group {
/**
* @desc Verify that the IUT can process all mandatory IEs in a LOCATION_REPORTING_CONTROL containing Event Type IE indicating Directly and sends a LOCATION_REPORT.
*
* Pics Selection: PICS A.3/10.1 and A.3/10.3
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of a LOCATION_REPORTING_CONTROL
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Request_Type
* containing an Event_Type
* indicating Directly
* containing a Report_Area
* indicating ECGI
* sends LOCATION_REPORT
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-UTRAN_CGI
* containing a PLMN_Identity
* containing a Cell_Identity
* containing a TAI
* containing a PLMN_Identity
* containing a TAC
* containing a Request_Type
* containing a Event_Type
* containing a Report_Area.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_LRP_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.11.1.2-2(1st dashed line) and 9.1.12.1 and 9.1.12.3 and 9.2.1.16,34,38
*/
testcase TC_S1AP_eNB_LRP_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_LRP_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_LRP_01
/**
* @desc Verify that the IUT can process all mandatory IEs in a LOCATION_REPORTING_CONTROL containing Event Type IE indicating Change of service cell and sends a LOCATION_REPORT.
*
* Pics Selection: PICS A.3/10.1 and A.3/10.3
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of a LOCATION_REPORTING_CONTROL
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Request_Type
* containing an Event_Type
* indicating change_of_service_cell
* containing a Report_Area
* indicating ECGI
* when UE changes to new cell
* sends LOCATION_REPORT
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-UTRAN_CGI
* containing a PLMN_Identity
* containing a Cell_Identity
* containing a TAI
* containing a PLMN_Identity
* containing a TAC
* containing a Request_Type
* containing a Event_Type
* containing a Report_Area.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_LRP_02
* @reference ETSI TS 136 413 V13.4.0 Clause 8.11.1.2-2(1st dashed line) and 9.1.12.1 and 9.1.12.3 and 9.2.1.16,34,38
*/
testcase TC_S1AP_eNB_LRP_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_LRP_02());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_LRP_02
/**
* @desc Verify that the IUT can process all mandatory IEs in a LOCATION_REPORTING_CONTROL containing Event Type IE indicating Stop change of service cell and sends a LOCATION_REPORT.
*
* Pics Selection: PICS A.3/10.1 and A.3/10.3
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of a LOCATION_REPORTING_CONTROL
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Request_Type
* containing an Event_Type
* indicating stop_change_of_service_cell
* containing a Report_Area
* indicating ECGI
* when UE changes to new cell
* sends LOCATION_REPORT
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-UTRAN_CGI
* containing a PLMN_Identity
* containing a Cell_Identity
* containing a TAI
* containing a PLMN_Identity
* containing a TAC
* containing a Request_Type
* containing a Event_Type
* containing a Report_Area.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_LRP_03
* @reference ETSI TS 136 413 V13.4.0 Clause 8.11.1.2-2(1st dashed line) and 9.1.12.1 and 9.1.12.3 and 9.2.1.16,34,38
*/
testcase TC_S1AP_eNB_LRP_03() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_LRP_03());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_LRP_03
/**
* @desc Verify that the IUT can send a LOCATION REPORT_FAILURE_INDICATION.
*
* Pics Selection: PICS A.3/10.1 and A.3/10.3
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of a LOCATION_REPORTING_CONTROL
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Request_Type
* containing an Event_Type
* containing a Report_Area
* sends LOCATION REPORT_FAILURE_INDICATION
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Cause
* indicating an appropriate cause value.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_LRP_04
* @reference ETSI TS 136 413 V13.4.0 Clause 8.11.2.2-1 and 9.1.12.2
*/
testcase TC_S1AP_eNB_LRP_04() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_LRP_04());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_LRP_04
} // End of group Location_reporting_group
/**
* @desc Warning message transmission group
* @see ETSI TS 103 497-2 Clause 5.2.2.1.12 Warning message transmission group
*/
group Warning_message_transmission_group {
/**
* @desc Verify that the IUT can successfully process all mandatory IEs in a WRITE-REPLACE_WARNING_REQUEST received and sends a WRITE-REPLACE_WARNING_RESPONSE.
*
* Pics Selection: PICS A.3/11.1
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of an WRITE-REPLACE_WARNING_REQUEST
* containing a Message_Identifier
* containing a Serial_Number
* containing a Repetition Period
* containing an Number_of_Broadcasts_Requested
* sends an WRITE-REPLACE_WARNING_RESPONSE
* containing a Serial_Number.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_WTP_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.12.1.2-1 and 9.1.13.1 and 9.1.13.2
*/
testcase TC_S1AP_eNB_WTP_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_WTP_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_WTP_01
/**
* @desc Verify that the IUT can successfully process all mandatory IEs in an KILL_REQUEST received and sends a KILL_RESPONSE.
*
* Pics Selection: PICS A.3/11.2
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of a KILL_REQUEST
* containing a Message_Identifier
* containing a Serial_Number
* sends sends a KILL_RESPONSE
* containing a Message_Identifier
* containing a Serial_Number.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_WTP_02
* @reference ETSI TS 136 413 V13.4.0 Clause 8.12.2.2-1,3 and 9.1.13.3 and 9.1.13.4
*/
testcase TC_S1AP_eNB_WTP_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_WTP_02());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_WTP_02
/**
* @desc Verify that the IUT can send a PWS_RESTART_INDICATION to indicate a PWS Restart Indication procedure.
*
* Pics Selection: PICS A.3/11.3
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a PWS Restart Indication procedure
* sends a PWS_RESTART_INDICATION
* containing an E-CGI_List_for_Restart
* indicating a valid list of E-CGI
* containing a Global_ENB_ID
* containing a TAI_List_for_Restart
* indicating a valid list of eNB identifier
* containing an Emergency_Area_ID_List_for_Restart
* indicating an empty list.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_WTP_03
* @reference ETSI TS 136 413 V13.4.0 Clause 8.12.3.2 and 9.1.13.5
*/
testcase TC_S1AP_eNB_WTP_03() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_WTP_03());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_WTP_03
/**
* @desc Verify that the IUT can send a PWS_FAILURE_INDICATION to indicate PWS Failure Indication procedure.
*
* Pics Selection: PICS A.3/11.4
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a PWS Failure Indication procedure
* sends a PWS_FAILURE_INDICATION
* containing an PWS failed E-CGI List
* indicating a valid list of E-CGI
* containing a Global_ENB_ID.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_WTP_04
* @reference ETSI TS 136 413 V13.4.0 Clause 8.12.4.2 and 9.1.13.6
*/
testcase TC_S1AP_eNB_WTP_04() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_WTP_04());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_WTP_04
} // End of group Warning_message_transmission_group
/**
* @desc eNB direct information transfer group
* @see ETSI TS 103 497-2 Clause 5.2.2.1.13 eNB direct information transfer group
*/
group ENB_direct_information_transfer_group {
/**
* @desc Verify that the IUT can send an eNB_DIRECT_INFORMATION_TRANSFER to indicate an eNB Direct Information Transfer procedure.
*
* Pics Selection: PICS A.4/12
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an eNB direct information Transfer procedure,
* sends an eNB_DIRECT_INFORMATION_TRANSFER
* containing an Inter-system_Information_Transfer_Type
* containing a RIM
* containing a RIM_Transfer
* containing a RIM_Information
* containing a RIM_Routing_Address.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_EIT_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.13.2.1 and 9.1.14 and 9.2.3.23
*/
testcase TC_S1AP_eNB_EIT_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_EIT_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_EIT_01
} // End of group ENB_direct_information_transfer_group
/**
* @desc eNB configuration transfer group
* @see ETSI TS 103 497-2 Clause 5.2.2.1.15 eNB configuration transfer group
*/
group ENB_configuration_transfer_group {
/**
* @desc Verify that the IUT can send an eNB_CONFIGURATION_TRANSFER to indicate an eNB Configuration Transfer procedure.
*
* Pics Selection: PICS A.4/14
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an eNB Configuration Transfer procedure,
* sends an eNB_CONFIGURATION_TRANSFER
* containing a SON_Configuration_Transfer
* containing a Target_eNB-ID
* containing a Source_eNB-ID
* containing a SON_Information.
* containing a SON_Information_Request
* indicating X2TNL_Configuration_Info
* containing an X2_TNL_Configuration_Info.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_ECT_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.15.2.1 and 9.1.16
*/
testcase TC_S1AP_eNB_ECT_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component configuration
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_ECT_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_ECT_01
} // End of group ENB_configuration_transfer_group
/**
* @desc LPPa transport group
* @see ETSI TS 103 497-2 Clause 5.2.2.1.17 LPPa transport group
*/
group LPPa_transport_group {
/**
* @desc Verify that the IUT can send a UPLINK_UE_ASSOCIATED_LPPA_TRANSPORT to indicate a LPPa Transport procedure
* using a UE associated signalling.
*
* Pics Selection: PICS A.3/16.2
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a LPPa Transport procedure using a UE associated signalling,
* sends a UPLINK_UE_ASSOCIATED_LPPA_TRANSPORT
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Routing_ID
* indicating a valid routing identifier value
* containing an LPPa-PDU.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_LPP_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.17.2.2 and 9.1.19.2
*/
testcase TC_S1AP_eNB_LPP_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component configuration
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_LPP_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_LPP_01
/**
* @desc Verify that the IUT can send a UPLINK_UE_ASSOCIATED_LPPA_TRANSPORT to indicate a LPPa Transport procedure
* using a Non-UE associated signalling.
*
* Pics Selection: PICS A.3/16.4
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a LPPa Transport procedure using a UE associated signalling,
* sends a UPLINK_UE_ASSOCIATED_LPPA_TRANSPORT
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Routing_ID
* indicating a valid routing identifier value
* containing an LPPa-PDU.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_LPP_02
* @reference ETSI TS 136 413 V13.4.0 Clause 8.17.2.4 and 9.1.19.4
*/
testcase TC_S1AP_eNB_LPP_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component configuration
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
v_s1ap_enb.start(f_TC_S1AP_eNB_LPP_02());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_eNB_LPP_02
} // End of group LPPa_transport_group
} // End of group eNB_Role
group MME_Role { // TODO Review all preamble action: E-RAB Setup is exchanged for MME role, shall not be f_rABSetupRequest
/**
* @desc E-RAB management group
* @see ETSI TS 103 497-2 Clause 5.2.2.2.2 E-RAB management group
*/
group ERAB_management_group {
/**
* @desc Verify that the IUT can send an E-RAB_SETUP_REQUEST with at least one E-RAB IE to indicate an E-RAB Setup procedure.
*
* Pics Selection: PICS A.4/1.1
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an E-RAB Setup procedure,
* sends an E-RAB_SETUP_REQUEST
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-RAB_to_be_Setup_List
* containing an E-RAB_to_be_Setup Item 1
* containing an E-RAB_ID
* containing an E-RAB_Level_QoS_Parameters
* containing a Transport_Layer_Address
* containing a GTP-TEID
* containing a NAS-PDU.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_eNB_RAB_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.2.1.2 and 9.1.3.1
*/
testcase TC_S1AP_MME_RAB_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component configuration
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_RAB_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_RAB_01
} // End of group ERAB_management_group
/**
* @desc Paging group
* @see ETSI TS 103 497-2 Clause 5.2.2.2.5 Paging group
*/
group Pagin_group {
/**
* @desc Verify that the IUT can send a PAGING to indicate a Paging procedure.
*
* Pics Selection: A.4/4.4
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a Paging procedure
* sends a PAGING
* containing a UE_Identity_Index_value
* containing a UE_Paging_Identity
* containing a S-TMSI
* containing an IMSI
* containing a CN_Domain.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_PAG_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.5.2¶1 and 9.1.6
*/
testcase TC_S1AP_MME_PAG_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_PAG_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_PAG_01
} // End of group Paging group
/**
* @desc Management group
* @see ETSI TS 103 497-2 Clause 5.2.2.1.6 NAS transport group
*/
group NAS_transport_group {
/**
* @desc Verify that the IUT can send a DOWNLINK_NAS_TRANSPORT to indicate an ongoing NAS Transport procedure.
*
* Pics Selection: A.4/5.2
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an ongoing NAS Transport procedure
* sends a DOWNLINK_NAS_TRANSPORT
* containing an MME UE S1AP ID
* containing an eNB_UE_S1AP_ID
* containing a NAS-PDU.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_NAS_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.6.2.2¶1 and 9.1.7.2
*/
testcase TC_S1AP_MME_NAS_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_NAS_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_NAS_01
/**
* @desc Verify that the IUT can send a REROUTE_NAS_REQUEST to indicate a Reroute NAS Request procedure.
*
* Pics Selection: A.4/5.5
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a Reroute NAS Request procedure
* sends a REROUTE_NAS_REQUEST
* containing an MME UE S1AP ID
* containing a S1_Message
* containing an MME_Group_ID.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_NAS_02
* @reference ETSI TS 136 413 V13.4.0 Clause 8.6.2.2¶1 and 9.1.7.2
*/
testcase TC_S1AP_MME_NAS_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_NAS_02());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_NAS_02
} // End of group NAS_transport_group
/**
* @desc Management group
* @see ETSI TS 103 497-2 Clause 5.2.2.2.7 Management group
*/
group Management_group {
/**
* @desc Verify that the IUT can send a RESET to indicate a Reset procedure initiated from the MME.
*
* Pics Selection: A.4/6.1.2
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a Reset procedure initiated from the MME
* sends a RESET
* containing a Cause
* indicating an appropriate cause value
* containing a Reset_Type
* containing a S1_Interface
* indicating a value ‘Reset_all’.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_MNP_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.1.2.1¶2 and 9.1.8.1 and 9.1.8.2
*/
testcase TC_S1AP_MME_MNP_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MNP_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MNP_01
/**
* @desc Verify that the IUT can send process successfully all mandatory IEs in a RESET and sends a RESET_ACKNOWLEDGE
* due to a Reset procedure initiated from the E-UTRAN.
*
* Pics Selection: A.4/6.1.1
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of a RESET
* containing a Cause
* indicating an appropriate cause value
* containing a Reset_Type
* containing an S1_Interface
* indicating value ‘Reset_all’
* sends a RESET_ACKNOWLEDGE
* containing a UE-associated_logical_S1-connection_list.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_MNP_02
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.1.2.1¶2 and 9.1.8.1 and 9.1.8.2
*/
testcase TC_S1AP_MME_MNP_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MNP_02());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MNP_02
/**
* @desc Verify that the IUT can successfully all mandatory IEs in a RESET and sends a RESET_ACKNOWLEDGE
* due to a Reset procedure in case of Abnormal Condition at the EPC.
*
* Pics Selection: A.4/6.1.1
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of a RESET
* containing a Cause
* indicating an appropriate cause value
* containing a Reset_Type
* containing a Part_of_S1_interface
* indicating an empty ‘UE-associated_logical_S1-connection’
* sends a RESET_ACKNOWLEDGE
* containing a UE-associated_logical_S1-connection_list
* indicating an empty ‘UE-associated_logical_S1-connection’.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_MNP_03
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.1.3.2¶1 and 9.1.8.1 and 9.1.8.2
*/
testcase TC_S1AP_MME_MNP_03() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MNP_03());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MNP_03
/**
* @desc Verify that the IUT can send a RESET to indicate a Reset procedure initiated from the eNB.
*
* Pics Selection: A.4/6.2.2
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an Error Indication procedure
* sends an ERROR_INDICATION
* (containing a Cause
* or containing a Criticality_Diagnostics).
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_MNP_04
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.1.2.1¶2 and 9.1.8.1 and 9.1.8.2
*/
testcase TC_S1AP_MME_MNP_04() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MNP_04());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MNP_04
/**
* @desc Verify that the IUT can process all mandatory IEs in a S1_SETUP_REQUEST and
* sends a S1_SETUP_RESPONSE to indicate a S1 Setup procedure.
*
* Pics Selection: A.4/6.3
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of a S1_SETUP_REQUEST
* containing a Global_eNB_ID
* containing a Supported_TAs
* containing a TAC
* containing a Default_Paging_DRX
* sends a S1_SETUP_RESPONSE.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_MNP_05
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.3.2¶1 and 9.1.8.4 and 9.1.8.5
*/
testcase TC_S1AP_MME_MNP_05() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MNP_05());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MNP_05
/**
* @desc Verify that the IUT can process all mandatory IEs in a S1_SETUP_REQUEST and
* sends a S1_SETUP_FAILURE to indicate an invalid S1 Setup procedure due to an unknown PLMN identities.
*
* Pics Selection: A.4/6.3
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of a S1_SETUP_REQUEST
* containing a Global_eNB_ID
* containing a Supported_TAs
* containing a TAC
* containing a Broadcast_PLMNs
* indicating at least one unknown PLMN identity
* sends a S1_SETUP_FAILURE
* containing a Cause
* indicating the cause value 'Unknown PLMN'.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_MNP_06
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.3.2¶1 and 9.1.8.4 and 9.1.8.6
*/
testcase TC_S1AP_MME_MNP_06() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MNP_06());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MNP_06
/**
* @desc Verify that the IUT can process all mandatory IEs in an ENB_CONFIGURATION_UPDATE and
* sends an ENB_CONFIGURATION_UPDATE_ACKNOWLEDGE to indicate an eNB Configuration Update procedure.
*
* Pics Selection: A.4/6.4
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of an ENB_CONFIGURATION_UPDATE
* containing a Global_eNB_ID
* containing a Supported_TAs
* containing a TAC
* sends an MME_CONFIGURATION_UPDATE_ACKNOWLEDGE.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_MNP_07
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.4.2¶1 and 9.1.8.7 and 9.1.8.8
*/
testcase TC_S1AP_MME_MNP_07() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MNP_07());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MNP_07
/**
* @desc Verify that the IUT can process all mandatory IEs in an ENB_CONFIGURATION_UPDATE and
* sends an ENB_CONFIGURATION_UPDATE_FAILURE to indicate an invalid eNB Configuration Update procedure due to an invalid Global eNB identifier.
*
* Pics Selection: A.4/6.4
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of an ENB_CONFIGURATION_UPDATE
* containing a Global_eNB_ID
* indicating invalid value
* sends an ENB_CONFIGURATION_UPDATE_FAILURE
* containing a Cause
* indicating an appropriate cause value.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_MNP_08
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.3.2¶1 and 9.1.8.7 and 9.1.8.9
*/
testcase TC_S1AP_MME_MNP_08() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MNP_08());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MNP_08
/**
* @desc Verify that the IUT can send an ENB_CONFIGURATION_UPDATE to indicate an eNB Configuration Update procedure.
*
* Pics Selection: A.4/6.5
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an eNB Configuration Update procedure
* sends an ENB_CONFIGURATION_UPDATE
* containing a Global_eNB_ID
* containing a Supported_TAs
* containing a TAC.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_MNP_09
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.4.2¶1 and 9.1.8.10
*/
testcase TC_S1AP_MME_MNP_09() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MNP_09());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MNP_09
/**
* @desc Verify that the IUT can send an OVERLOAD_START to indicate an Overload Start procedure.
*
* Pics Selection: A.4/6.6
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an Overload Start procedure
* sends an OVERLOAD_START
* containing an Overload_Response.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_MNP_10
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.6.2¶1 and 9.1.8.13
*/
testcase TC_S1AP_MME_MNP_10() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MNP_10());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MNP_10
/**
* @desc Verify that the IUT can send an OVERLOAD_STOP to indicate an Overload Stop procedure.
*
* Pics Selection: A.4/6.7
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an Overload Stop procedure
* sends an OVERLOAD_STOP
* containing an Overload_Response.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_MNP_11
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.7.2¶1 and 9.1.8.14
*/
testcase TC_S1AP_MME_MNP_11() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MNP_11());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MNP_11
} // End of group Management_group
/**
* @desc S1 CDMA 2000 tunnelling group group
* @see ETSI TS 103 497-2 Clause 5.2.2.2.8 S1 CDMA 2000 tunnelling group group
*/
group S1_CDMA_2000_tunelling_group {
/**
* @desc Verify that the IUT can send a DOWNLINK_S1_CDMA2000_TUNNELLING.
*
* Pics Selection: PICS A.3/7.1
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a CDMA2000 signalling event
* sends a DOWNLINK_S1_CDMA2000_TUNNELLING
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* not containing an E-RABs_Subject_to_Forwarding_Lis
* containing a CDMA2000_HO_type
* containing a CDMA2000_PDU.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_STP_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.8.2.1¶1 and 9.1.9.1
*/
testcase TC_S1AP_MME_STP_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_STP_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_STP_01
} // End of group S1_CDMA_2000_tunelling_group
/**
* @desc Warning message transmission group
* @see ETSI TS 103 497-2 Clause 5.2.2.2.10 Trace group
*/
group Trace_group {
/**
* @desc Verify that the IUT can send a TRACE_START message to indicate Trace Start procedure.
*
* Pics Selection: A.4/9.1
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a Trace Start procedure
* sends a TRACE_START
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Trace_Activation
* containing an E-UTRAN_Trace_ID
* containing a Interfaces_To_Trace
* indicating value ‘S1-MME’
* containing a Trace_depth
* indicating value ‘maximum’
* containing a Trace_Collection_Entity_IP_Address.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_TRP_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.10.1.2¶1 and 9.1.11.1 and 9.2.1.4
*/
testcase TC_S1AP_MME_TRP_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_TRP_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_TRP_01
/**
* @desc Verify that the IUT can successfully process all mandatory IEs in a DEACTIVATE_TRACE.
*
* Pics Selection: A.4/9.3
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a Deactivate Trace procedure
* sends a DEACTIVATE_TRACE
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-UTRAN_Trace_ID.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_TRP_02
* @reference ETSI TS 136 413 V13.4.0 Clause 8.10.1.211 and 9.1.11.2
*/
testcase TC_S1AP_MME_TRP_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_TRP_02());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_TRP_02
} // End of goup Trace_group
/**
* @desc Warning message transmission group
* @see ETSI TS 103 497-2 Clause 5.2.2.2.11 Location reporting group
*/
group Location_reporting_group {
/**
* @desc Verify that the IUT can send a LOCATION_REPORTING_CONTROL.
*
* Pics Selection: A.4/10.1 and A.4/10.3
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a Location Reporting Control procedure
* sends a LOCATION_REPORTING_CONTROL
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Request_Type
* containing a Event_Type
* containing a Report_Area
* indicating ECGI.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_LRP_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.11.1.2-1 and 9.1.12.1 and 9.1.12.3 and 9.2.1.16,34,38
*/
testcase TC_S1AP_MME_LRP_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_LRP_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_LRP_01
/**
* @desc Verify that the IUT can send a LOCATION_REPORTING_CONTROL and process all mandatory IEs in a LOCATION REPORT_FAILURE_INDICATION.
*
* Pics Selection: A.4/10.1 and A.4/10.3
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a Location Reporting Control procedure
* sends a LOCATION_REPORTING_CONTROL
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Request_Type
* containing a Event_Type
* containing a Report_Area
* indicating ECGI
* receives a LOCATION_REPORT_FAILURE_INDICATION
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Cause
* indicating an appropriate cause value.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_LRP_02
* @reference ETSI TS 136 413 V13.4.0 Clause 8.11.1.2-1 and 9.1.12.1 and 9.1.12.3 and 9.2.1.16,34,38
*/
testcase TC_S1AP_MME_LRP_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_LRP_02());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_LRP_02
} // End of group Location_reporting_group
/**
* @desc Warning message transmission group
* @see ETSI TS 103 497-2 Clause 5.2.2.2.12 Warning message transmission group
*/
group Warning_message_transmission_group {
/**
* @desc Verify that the IUT can send a WRITE-REPLACE_WARNING_REQUEST to indicate a Warning Message Transmission procedure.
*
* Pics Selection: PICS A.4/11.1
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a Warning Message Transmission procedure
* sends a WRITE-REPLACE_WARNING_REQUEST
* containing a Message_Identifier
* containing a Serial_Number
* containing a Repetition Period
* containing an Number_of_Broadcasts_Requested
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_WTP_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.12.1.2-1 and 9.1.13.1 and 9.1.13.2
*/
testcase TC_S1AP_MME_WTP_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_WTP_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_WTP_01
/**
* @desc Verify that the IUT can send a KILL_REQUEST to cancel an already ongoing broadcast of a Warning Message Transmission procedure.
*
* Pics Selection: PICS A.4/11.2
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a cancellation of an ongoing Warning Message Transmission procedure
* sends a KILL_REQUEST
* containing a Message_Identifier
* containing a Serial_Number
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_WTP_02
* @reference ETSI TS 136 413 V13.4.0 Clause 8.12.2.2-1 and 9.1.13.3 and 9.1.13.4
*/
testcase TC_S1AP_MME_WTP_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_WTP_02());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_WTP_02
} // End of group Warning_message_transmission_group
/**
* @desc MME direct information transfer group
* @see ETSI TS 103 497-2 Clause 5.2.2.2.14 MME direct information transfer group
*/
group MME_direct_information_transfer_group {
/**
* @desc Verify that the IUT can send an MME_DIRECT_INFORMATION_TRANSFER to indicate an MME Configuration Transfer procedure.
*
* Pics Selection: PICS A.4/13
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an MME Direct Information Transfer procedure,
* sends an MME_DIRECT_INFORMATION_TRANSFER
* containing an Inter-system_Information_Transfer_Type
* containing a RIM
* containing a RIM_Transfer
* containing a RIM_Information.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_MIT_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.14.2.1 and 9.2.3.23
*/
testcase TC_S1AP_MME_MIT_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component configuration
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MIT_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MIT_01
} // End of group MME_direct_information_transfer_group
/**
* @desc MME configuration transfer
* @see ETSI TS 103 497-2 Clause 5.2.2.2.16 MME configuration transfer group
*/
group MME_configuration_transfer_group {
/**
* @desc Verify that the IUT can send an MME_CONFIGURATION_TRANSFER to indicate an MME Configuration Transfer procedure.
*
* Pics Selection: PICS A.4/15
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an MME Configuration Transfer procedure,
* sends an MME_CONFIGURATION_TRANSFER
* containing a SON_Configuration_Transfer
* containing a Target_eNB-ID
* containing a Source_eNB-ID
* containing a SON_Information.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_MCT_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.16.2.1 and 9.1.17
*/
testcase TC_S1AP_MME_MCT_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component configuration
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MCT_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MCT_01
} // End of group MME_configuration_transfer_group
/**
* @desc LPPa transport group
* @see ETSI TS 103 497-2 Clause 5.2.2.2.17 LPPa transport group
*/
group LPPa_transport_group {
/**
* @desc Verify that the IUT can send a DOWNLINK_UE_ASSOCIATED_LPPA_TRANSPORT to indicate a LPPa Transport procedure
* using a UE associated signalling.
*
* Pics Selection: PICS A.4/16.1
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a LPPa Transport procedure using a UE associated signalling,
* sends a DOWNLINK_UE_ASSOCIATED_LPPA_TRANSPORT
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Routing_ID
* indicating a valid routing identifier value
* containing an LPPa-PDU.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_LPP_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.17.2.1 and 9.1.19.1
*/
testcase TC_S1AP_MME_LPP_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component configuration
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_LPP_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_LPP_01
/**
* @desc Verify that the IUT can send a DOWNLINK_UE_ASSOCIATED_LPPA_TRANSPORT to indicate a LPPa Transport procedure
* using a non-UE associated signalling.
*
* Pics Selection: PICS A.3/16.3
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a LPPa Transport procedure using a UE associated signalling,
* sends a DOWNLINK_UE_ASSOCIATED_LPPA_TRANSPORT
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Routing_ID
* indicating a valid routing identifier value
* containing an LPPa-PDU.
*
*
* @see ETSI TS 103 497-2 TP_S1AP_MME_LPP_02
* @reference ETSI TS 136 413 V13.4.0 Clause 8.17.2.3 and 9.1.19.3
*/
testcase TC_S1AP_MME_LPP_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component configuration
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_LPP_02());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_LPP_02
} // End of group LPPa_transport_group
} // End of group MME_Role
} // End of module S1AP_TestCases