Newer
Older
- 0 - `yawRateUsed` - if the yaw rate is used,
- 1 - `yawRateNotUsed` - if the yaw rate is not used,
- 2 - `unavailable` - if the information of curvature calculation mode is unknown.
**Categories**: Vehicle information
**Revision**: _V1.3.1_
```asn1
CurvatureCalculationMode ::= ENUMERATED {
yawRateUsed (0),
yawRateNotUsed (1),
unavailable (2),
...
}
```
### <a name="CurvatureConfidence"></a>CurvatureConfidence
This DE indicates the acceleration confidence value which represents the estimated absolute accuracy range of a curvature value with a confidence level of 95%.
If required, the confidence level can be defined by the corresponding standards applying this DE.
- 0 - `onePerMeter-0-00002` if the confidence value is less than or equal to 0,00002 m-1,
- 1 - `onePerMeter-0-0001` if the confidence value is less than or equal to 0,0001 m-1 and greater than 0,00002 m-1,
- 2 - `onePerMeter-0-0005` if the confidence value is less than or equal to 0,0005 m-1 and greater than 0,0001 m-1,
- 3 - `onePerMeter-0-002` if the confidence value is less than or equal to 0,002 m-1 and greater than 0,0005 m-1,
- 4 - `nePerMeter-0-01` if the confidence value is less than or equal to 0,01 m-1 and greater than 0,002 m-1,
- 5 - `nePerMeter-0-1` if the confidence value is less than or equal to 0,1 m-1 and greater than 0,01 m-1,
- 6 - `outOfRange` if the confidence value is out of range, i.e. greater than 0,1 m-1,
- 7 - `unavailable` if the confidence value is not available.
**Categories**: Vehicle information
**Revision**: _Description revised in V2.1.1_
NOTE: If a curvature value is received and its confidence value is set to 'outOfRange(6)', it means that the curvature value is not valid
1040
1041
1042
1043
1044
1045
1046
1047
1048
1049
1050
1051
1052
1053
1054
1055
1056
1057
1058
1059
1060
and therefore cannot be trusted. Such value is not useful for the application.
>>>
```asn1
CurvatureConfidence ::= ENUMERATED {
onePerMeter-0-00002 (0),
onePerMeter-0-0001 (1),
onePerMeter-0-0005 (2),
onePerMeter-0-002 (3),
onePerMeter-0-01 (4),
onePerMeter-0-1 (5),
outOfRange (6),
unavailable (7)
}
```
### <a name="CurvatureValue"></a>CurvatureValue
This DE describes vehicle turning curve with the following information:
```
Value = 1 / Radius * 10000
```
wherein radius is the vehicle turning curve radius in metres.
Positive values indicate a turning curve to the left hand side of the driver.
It corresponds to the vehicle coordinate system as defined in ISO 8855 [2].
The value shall be set to:
- `-1023` for values smaller than -1023,
- `n` (`n > -1023` and `n < 0) for negative values equal to or less than n, and greater than (n-1),
- `0` when the vehicle is moving straight,
- `n` (`n > 0` and `n < 1022) for positive values equal to or less than n, and greater than (n-1),
- `1022`, for values greater than 1021,
1072
1073
1074
1075
1076
1077
1078
1079
1080
1081
1082
1083
1084
1085
1086
1087
1088
1089
1090
1091
1092
1093
1094
1095
1096
- `1023`, if the information is not available.
**Unit**: _1 over 10 000 metres_
**Categories**: Vehicle information
**Revision**: _description revised in V2.1.1 (the definition of value 1022 has changed slightly)_
>>>
NOTE: The present DE is limited to vehicle types as defined in ISO 8855 [2].
>>>
```asn1
CurvatureValue ::= INTEGER {
outOfRangeNegative (-1023),
straight (0),
outOfRangePositive (1022),
unavailable (1023)
} (-1023..1023)
```
### <a name="DangerousEndOfQueueSubCauseCode"></a>DangerousEndOfQueueSubCauseCode
This DE represents the value of the sub cause codes of the [**CauseCode**](#CauseCode) `dangerousEndOfQueue`.
1098
1099
1100
1101
1102
1103
1104
1105
1106
1107
1108
1109
1110
1111
1112
1113
1114
1115
1116
1117
1118
1119
1120
1121
- 0 - `unavailable` - in case information on the type of dangerous queue is unavailable,
- 1 - `suddenEndOfQueue`- in case a sudden end of queue is detected, e.g. due to accident or obstacle,
- 2 - `queueOverHill` - in case the dangerous end of queue is detected on the road hill,
- 3 - `queueAroundBend` - in case the dangerous end of queue is detected around the road bend,
- 4 - `queueInTunnel` - in case queue is detected in tunnel,
- 5-255 - reserved for future usage.
**Categories**: Traffic information
**Revision**: _V1.3.1_
```asn1
DangerousEndOfQueueSubCauseCode ::= INTEGER {
unavailable (0),
suddenEndOfQueue (1),
queueOverHill (2),
queueAroundBend (3),
queueInTunnel (4)
} (0..255)
```
### <a name="DangerousGoodsBasic"></a>DangerousGoodsBasic
This DE indicates the type of the dangerous goods being carried by a heavy vehicle.
The value is assigned according to `class` and `division` definitions of dangerous goods as specified in part II,
chapter 2.1.1.1 of European Agreement concerning the International Carriage of Dangerous Goods by Road [i.3].
1124
1125
1126
1127
1128
1129
1130
1131
1132
1133
1134
1135
1136
1137
1138
1139
1140
1141
1142
1143
1144
1145
1146
1147
1148
1149
1150
1151
1152
1153
1154
1155
1156
1157
1158
1159
1160
1161
1162
**Categories**: Vehicle information
**Revision**: _V1.3.1_
```asn1
DangerousGoodsBasic::= ENUMERATED {
explosives1 (0),
explosives2 (1),
explosives3 (2),
explosives4 (3),
explosives5 (4),
explosives6 (5),
flammableGases (6),
nonFlammableGases (7),
toxicGases (8),
flammableLiquids (9),
flammableSolids (10),
substancesLiableToSpontaneousCombustion (11),
substancesEmittingFlammableGasesUponContactWithWater (12),
oxidizingSubstances (13),
organicPeroxides (14),
toxicSubstances (15),
infectiousSubstances (16),
radioactiveMaterial (17),
corrosiveSubstances (18),
miscellaneousDangerousSubstances (19)
}
```
### <a name="DangerousSituationSubCauseCode"></a>DangerousSituationSubCauseCode
This DE represents the value of the sub cause codes of the [**CauseCode**](#CauseCode) `dangerousSituation`
The value shall be set to:
- 0 - `unavailable` - in case information on the type of dangerous situation is unavailable,
- 1 - `emergencyElectronicBrakeEngaged` - in case emergency electronic brake is engaged,
- 2 - `preCrashSystemEngaged` - in case pre-crash system is engaged,
- 3 - `espEngaged` - in case Electronic Stability Program (ESP) system is engaged,
- 4 - `absEngaged` - in case Anti-lock Braking System (ABS) is engaged,
1164
1165
1166
1167
1168
1169
1170
1171
1172
1173
1174
1175
1176
1177
1178
1179
1180
1181
1182
1183
1184
1185
1186
1187
1188
1189
1190
1191
- 5 - `aebEngaged` - in case Autonomous Emergency Braking (AEB) system is engaged,
- 6 - `brakeWarningEngaged` - in case brake warning is engaged,
- 7 - `collisionRiskWarningEngaged` - in case collision risk warning is engaged,
- 8-255 - reserved for future usage.
**Categories**: Traffic information
**Revision**: _V1.3.1_
```asn1
DangerousSituationSubCauseCode ::= INTEGER {
unavailable (0),
emergencyElectronicBrakeEngaged (1),
preCrashSystemEngaged (2),
espEngaged (3),
absEngaged (4),
ebEngaged (5),
brakeWarningEngaged (6),
collisionRiskWarningEngaged (7)
} (0..255)
```
### <a name="DeltaAltitude"></a>DeltaAltitude
This DE represents an offset altitude with regards to a defined altitude value.
It may be used to describe a geographical point with regards to a specific reference geographical position.
The value shall be set to:
- `-12 700` for values equal to or lower than -127 metres,
- `n` (`n > -12 700` and `n <= 0) for altitude offset n x 0,01 metre below the reference position,
- `0` for no altitudinal offset,
- `n` (`n > 0` and `n < 12799`) for altitude offset n x 0,01 metre above the reference position,
- `12 799` for values equal to or greater than 127,99 metres,
- `12 800` when the information is unavailable.
**Categories**: GeoReference information
**Revision**: _editorial update in V2.1.1_
```asn1
DeltaAltitude ::= INTEGER {
negativeOutOfRange (-12700),
positiveOutOfRange (12799),
unavailable (12800)
} (-12700..12800)
```
### <a name="DeltaLatitude"></a>DeltaLatitude
This DE represents an offset latitude with regards to a defined latitude value.
It may be used to describe a geographical point with regards to a specific reference geographical position.
The value shall be set to:
- `n` (`n >= -131 071` and `n < 0`) for offset n x 10^-7 degree towards the south from the reference position,
- `n` (`n > 0` and `n < 131 072`) for offset n x 10^-7 degree towards the north from the reference position,
- `131 072` when the information is unavailable.
**Categories**: GeoReference information
**Revision**: _editorial update in V2.1.1_
```asn1
DeltaLatitude ::= INTEGER {
unavailable (131072)
} (-131071..131072)
```
### <a name="DeltaLongitude"></a>DeltaLongitude
This DE represents an offset longitude with regards to a defined longitude value.
It may be used to describe a geographical point with regards to a specific reference geographical position.
The value shall be set to:
- `n` (`n >= -131 071` and `n < 0`) for offset n x 10^-7 degree towards the west from the reference position,
- `n` (`n > 0` and `n < 131 072`) for offset n x 10^-7 degree towards the east from the reference position,
- `131 072` when the information is unavailable.
**Categories**: GeoReference information
**Revision**: _editorial update in V2.1.1_
```asn1
DeltaLongitude ::= INTEGER {
unavailable (131072)
} (-131071..131072)
```
### <a name="DeltaTimeMilliSecondPos"></a>DeltaTimeMilliSecondPos
This DE represents a difference in time with respect to a reference time.
Example: a time interval between two consecutive message transmissions.
**Categories**: Basic information
**Revision**: _Created in V2.1.1 from the DE TransmissionInterval in [i.2]_
```asn1
DeltaTimeMilliSecondPos ::= INTEGER (1..10000)
```
### <a name="DeltaTimeMilliSecondPosNeg"></a>DeltaTimeMilliSecondPosNeg
This DE represents a difference in time with respect to a reference time.
**Categories**: Basic information
**Revision**: _Created in V2.1.1_
```asn1
DeltaTimeMilliSecondPosNeg ::= INTEGER (-1500..1500)
```
### <a name="DeltaTimeQuarterSecond"></a>DeltaTimeQuarterSecond
This DE represents a difference in time with respect to a reference time.
It can be interpreted as the first 8 bits of a GenerationDeltaTime. To convert it to a [**GenerationDeltaTime**](#GenerationDeltaTime),
multiply by 256 (i.e. append a `00` byte)
**Categories**: Basic information
**Revision**: _Created in V2.1.1_
```asn1
DeltaTimeQuarterSecond::= INTEGER {
unavailable (255)
} (1..255)
1303
1304
1305
1306
1307
1308
1309
1310
1311
1312
1313
1314
1315
1316
1317
1318
1319
1320
1321
1322
1323
1324
1325
1326
1327
1328
1329
1330
1331
1332
1333
1334
1335
1336
1337
1338
```
### <a name="DeltaTimeTenthOfSecond"></a>DeltaTimeTenthOfSecond
This DE represents a difference in time with respect to a reference time.
**Unit**: _0,1 s_
**Categories**: Basic information
**Revision**: _Created in V2.1.1_
```asn1
DeltaTimeTenthOfSecond::= INTEGER {
unavailable (127)
} (0..127)
```
### <a name="DeltaTimeSecond"></a>DeltaTimeSecond
This DE represents a difference in time with respect to a reference time.
**Unit**: _1 s_
**Categories**: Basic information
**Revision**: _Created in V2.1.1 from ValidityDuration_
```asn1
DeltaTimeSecond ::= INTEGER (0..86400)
```
### <a name="Direction"></a>Direction
This DE indicates a direction with respect to a defined reference direction.
Example: a reference direction may be implicitly defined by the definition of a geographical zone.
The value shall be set to:
- 0 - `sameDirection` - to indicate the same direction as the reference direction,
- 1 - `oppositeDirection` - to indicate opposite direction as the reference direction,
- 2 - `bothDirections` - to indicate both directions, i.e. the same and the opposite direction,
- 3 - `unavailable` - to indicate that the information is unavailable.
**Categories**: GeoReference information
**Revision**: _Created in V2.1.1_
```asn1
Direction::= INTEGER{
sameDirection (0),
oppositeDirection (1),
bothDirections (2),
unavailable (3)
} (0..3)
```
### <a name="DriveDirection"></a>DriveDirection
This DE indicates in which direction something is moving.
The value shall be set to:
- 0 - `forward` - to indicate it is moving forward,
- 1 - `backwards` - to indicate it is moving backwards,
- 2 - `unavailable` - to indicate that the information is unavailable.
**Categories**: Kinematics information
**Revision**: _editorial update in V2.1.1_
```asn1
DriveDirection ::= ENUMERATED {
forward (0),
backward (1),
unavailable (2)
}
```
### <a name="DrivingLaneStatus"></a>DrivingLaneStatus
This DE indicates whether a driving lane is open to traffic.
A lane is counted from inside border of the road excluding the hard shoulder. The size of the bit string shall
correspond to the total number of the driving lanes in the carriageway.
The numbering is matched to [**LanePosition**](#LanePosition).
The bit `0` is used to indicate the innermost lane, bit `1` is used to indicate the second lane from inside border.
If a lane is closed to traffic, the corresponding bit shall be set to `1`. Otherwise, it shall be set to `0`.
**Categories**: Traffic information
**Revision**: _V1.3.1_
>>>
NOTE: hard shoulder status is not provided by this DE but in [**HardShoulderStatus**](#HardShoulderStatus).
1397
1398
1399
1400
1401
1402
1403
1404
1405
1406
1407
1408
1409
1410
1411
1412
1413
1414
1415
1416
1417
1418
1419
1420
>>>
```asn1
DrivingLaneStatus ::= BIT STRING (SIZE (1..13))
```
### <a name="EmbarkationStatus"></a>EmbarkationStatus
This DE indicates whether a vehicle (e.g. public transport vehicle, truck) is under the embarkation process.
If that is the case, the value is *TRUE*, otherwise *FALSE*.
**Categories**: Vehicle information
**Revision**: _editorial update in V2.1.1_
```asn1
EmbarkationStatus ::= BOOLEAN
```
### <a name="EmergencyPriority"></a>EmergencyPriority
This DE indicates the right of priority requested or assumed by an operating emergency vehicle.
The right-of-priority bit shall be set to `1` if the corresponding right is requested.
The corresponding bit shall be set to 1 under the following conditions:
- 0 - `requestForRightOfWay` - when the vehicle is requesting/assuming the right of way,
- 1 - `requestForFreeCrossingAtATrafficLight` - when the vehicle is requesting/assuming the right to pass at a (red) traffic light.
**Categories**: Traffic information
**Revision**: _description revised in V2.1.1_
```asn1
EmergencyPriority ::= BIT STRING {
requestForRightOfWay (0),
requestForFreeCrossingAtATrafficLight (1)
} (SIZE(2))
```
### <a name="EmergencyVehicleApproachingSubCauseCode"></a>EmergencyVehicleApproachingSubCauseCode
This DE represents the value of the sub cause codes of the [**CauseCode**](#CauseCode) "emergencyVehicleApproaching".
The value shall be set to:
- 0 - `unavailable` - in case further detailed information on the emergency vehicle approaching event
is unavailable,
- 1 - `emergencyVehicleApproaching` - in case an operating emergency vehicle is approaching,
- 2 - `prioritizedVehicleApproaching` - in case a prioritized vehicle is approaching,
- 3-255 - reserved for future usage.
**Categories**: Traffic information
**Revision**: _V1.3.1_
```asn1
EmergencyVehicleApproachingSubCauseCode ::= INTEGER {
unavailable (0),
emergencyVehicleApproaching (1),
prioritizedVehicleApproaching (2)
} (0..255)
```
### <a name="EnergyStorageType"></a>EnergyStorageType
This DE indicated the type of energy being used and stored in vehicle.
The corresponding bit shall be set to 1 under the following conditions:
- 0 - `hydrogenStorage` - when hydrogen is being used and stored in vehicle,
- 1 - `electricEnergyStorage` - when electric energy is being used and stored in vehicle,
- 2 - `liquidPropaneGas` - when liquid Propane Gas (LPG) is being used and stored in vehicle,
- 3 - `compressedNaturalGas ` - when compressedNaturalGas (CNG) is being used and stored in vehicle,
- 4 - `diesel` - when diesel is being used and stored in vehicle,
- 5 - `gasoline` - when gasoline is being used and stored in vehicle,
1469
1470
1471
1472
1473
1474
1475
1476
1477
1478
1479
1480
1481
1482
1483
1484
1485
1486
1487
1488
1489
1490
- 6 - `ammonia` - when ammonia is being used and stored in vehicle.
- Otherwise, the corresponding bit shall be set to `0`.
**Categories**: Vehicle information
**Revision**: _editorial revision in V2.1.1_
```asn1
EnergyStorageType ::= BIT STRING {
hydrogenStorage (0),
electricEnergyStorage (1),
liquidPropaneGas (2),
compressedNaturalGas (3),
diesel (4),
gasoline (5),
ammonia (6)
}(SIZE(7))
```
### <a name="EuVehicleCategoryL"></a>EuVehicleCategoryL
This DE represents one of the specific categories in the L category: L1, L2, L3, L4, L5, L6, or L7 according to UNECE/TRANS/WP.29/78/Rev.4 [i.16].
**Categories**: Vehicle information
**Revision**: _V2.1.1_
```asn1
EuVehicleCategoryL ::= ENUMERATED { l1, l2, l3, l4, l5, l6, l7 }
```
### <a name="EuVehicleCategoryM"></a>EuVehicleCategoryM
This DE represents one of the specific categories in the M category: M1, M2, or M3 according to UNECE/TRANS/WP.29/78/Rev.4 [i.16].
**Categories**: Vehicle information
**Revision**: _V2.1.1_
```asn1
EuVehicleCategoryM ::= ENUMERATED {m1, m2, m3}
```
### <a name="EuVehicleCategoryN"></a>EuVehicleCategoryN
This DE represents one of the specific categories in the N category: N1, N2, or N3 according to UNECE/TRANS/WP.29/78/Rev.4 [i.16].
**Categories**: Vehicle information
**Revision**: _V2.1.1_
```asn1
EuVehicleCategoryN ::= ENUMERATED {n1, n2, n3}
```
### <a name="EuVehicleCategoryO"></a>EuVehicleCategoryO
This DE represents one of the specific categories in the O category: O1, O2, O3 or O4 according to UNECE/TRANS/WP.29/78/Rev.4 [i.16].
**Categories**: Vehicle information
**Revision**: _V2.1.1_
```asn1
EuVehicleCategoryO ::= ENUMERATED {o1, o2, o3, o4}
```
### <a name="ExteriorLights"></a>ExteriorLights
This DE describes the status of the exterior light switches of a vehicle.
The corresponding bit shall be set to 1 under the following conditions:
- 0 - `lowBeamHeadlightsOn` - when the low beam head light switch is on,
- 1 - `highBeamHeadlightsOn` - when the high beam head light switch is on,
- 2 - `leftTurnSignalOn` - when the left turnSignal switch is on,
- 3 - `rightTurnSignalOn` - when the right turn signal switch is on,
- 4 - `daytimeRunningLightsOn` - when the daytime running light switch is on,
- 5 - `reverseLightOn` - when the reverse light switch is on,
- 6 - `fogLightOn` - when the tail fog light switch is on,
1549
1550
1551
1552
1553
1554
1555
1556
1557
1558
1559
1560
1561
1562
1563
1564
1565
1566
1567
1568
1569
1570
1571
1572
1573
1574
1575
1576
1577
1578
1579
1580
1581
1582
1583
1584
1585
1586
1587
1588
1589
1590
- 7 - `parkingLightsOn` - when the parking light switch is on.
If a vehicle is not equipped with a certain light or if the light switch status information is not available,
the corresponding bit shall be set to `0`.
As the bit value indicates only the state of the switch, the turn signal and hazard signal bit values shall not
alternate with the blinking interval.
For hazard indicator, the `leftTurnSignalOn` (2) and `rightTurnSignalOn` (3) shall be both set to 1.
**Categories**: Vehicle information
**Revision**: _Description revised in V2.1.1_
>>>
NOTE: The value of each bit indicates the state of the switch, which commands the corresponding light.
The bit corresponding to a specific light is set to `1`, when the corresponding switch is turned on,
either manually by the driver or automatically by a vehicle system. The bit value does not indicate
if the corresponding lamps are alight or not.
>>>
```asn1
ExteriorLights ::= BIT STRING {
lowBeamHeadlightsOn (0),
highBeamHeadlightsOn (1),
leftTurnSignalOn (2),
rightTurnSignalOn (3),
daytimeRunningLightsOn (4),
reverseLightOn (5),
fogLightOn (6),
parkingLightsOn (7)
} (SIZE(8))
```
### <a name="GenerationDeltaTime"></a>GenerationDeltaTime
This DE represents a timestamp based on TimestampIts modulo 65 536.
This means that generationDeltaTime = TimestampIts mod 65 536.
**Categories**: Time information
**Revision**: _Created in V2.1.1 based on ETSI TS 103 900 [i.1]_
```asn1
GenerationDeltaTime ::= INTEGER { oneMilliSec(1) } (0..65535)
```
### <a name="HardShoulderStatus"></a>HardShoulderStatus
This DE indicates the current status of a hard shoulder: whether it is available for special usage
(e.g. for stopping or for driving) or closed for all vehicles.
The value shall be set to:
- 0 - `availableForStopping` - if the hard shoulder is available for stopping in e.g. emergency situations,
- 1 - `closed` - if the hard shoulder is closed and cannot be occupied in any case,
- 2 - `availableForDriving` - if the hard shoulder is available for regular driving.
**Categories**: Traffic information
**Revision**: _Description revised in V2.1.1_
```asn1
HardShoulderStatus ::= ENUMERATED {
availableForStopping (0),
closed (1),
```
### <a name="HazardousLocation-AnimalOnTheRoadSubCauseCode"></a>HazardousLocation-AnimalOnTheRoadSubCauseCode
This DE represents the value of the sub cause code of the [**CauseCode**](#CauseCode) `hazardousLocation-AnimalOnTheRoad`.
The value shall be set to:
- 0 - `unavailable` - in case further detailed information on the animal on the road event is unavailable,
- 1 - `wildAnimals` - in case wild animals are detected on the road,
- 2 - `herdOfAnimals`- in case herd of animals are detected on the road,
- 3 - `smallAnimals` - in case small size animals are detected on the road,
- 4 - `largeAnimals` - in case large size animals are detected on the road.
- 5-255 - are reserved for future usage.
1629
1630
1631
1632
1633
1634
1635
1636
1637
1638
1639
1640
1641
1642
1643
1644
1645
1646
1647
1648
1649
1650
1651
1652
1653
**Categories**: Traffic information
**Revision**: _V1.3.1_
```asn1
HazardousLocation-AnimalOnTheRoadSubCauseCode ::= INTEGER {
unavailable (0),
wildAnimals (1),
herdOfAnimals (2),
smallAnimals (3),
largeAnimals (4)
} (0..255)
```
### <a name="HazardousLocation-DangerousCurveSubCauseCode"></a>HazardousLocation-DangerousCurveSubCauseCode
This DE represents the sub cause code of the [**CauseCode**](#CauseCode) `hazardousLocation-DangerousCurve`.
The value shall be set to:
- 0 - `unavailable` - in case further detailed information on the dangerous curve is unavailable,
- 1 - `dangerousLeftTurnCurve` - in case the dangerous curve is a left turn curve,
- 2 - `dangerousRightTurnCurve` - in case the dangerous curve is a right turn curve,
- 3 - `multipleCurvesStartingWithUnknownTurningDirection` - in case of multiple curves for which the starting curve turning direction is not known,
- 4 - `multipleCurvesStartingWithLeftTurn` - in case of multiple curves starting with a left turn curve,
- 5 - `multipleCurvesStartingWithRightTurn` - in case of multiple curves starting with a right turn curve.
1655
1656
1657
1658
1659
1660
1661
1662
1663
1664
1665
1666
1667
1668
1669
1670
1671
1672
1673
1674
1675
1676
1677
1678
1679
1680
1681
1682
1683
1684
1685
1686
- 6-255 - are reserved for future usage.
The definition of whether a curve is dangerous may vary according to region and according to vehicle types/mass
and vehicle speed driving on the curve. This definition is out of scope of the present document.
**Categories**: Traffic information
**Revision**: _V1.3.1_
```asn1
HazardousLocation-DangerousCurveSubCauseCode ::= INTEGER {
unavailable (0),
dangerousLeftTurnCurve (1),
dangerousRightTurnCurve (2),
multipleCurvesStartingWithUnknownTurningDirection (3),
multipleCurvesStartingWithLeftTurn (4),
multipleCurvesStartingWithRightTurn (5)
} (0..255)
```
### <a name="HazardousLocation-ObstacleOnTheRoadSubCauseCode"></a>HazardousLocation-ObstacleOnTheRoadSubCauseCode
This DE represents the value of the sub cause code of the [**CauseCode**](#CauseCode) `hazardousLocation-ObstacleOnTheRoad`.
The value shall be set to:
- 0 - `unavailable` - in case further detailed information on the detected obstacle is unavailable,
- 1 - `shedLoad` - in case detected obstacle is large amount of obstacles (shedload),
- 2 - `partsOfVehicles`- in case detected obstacles are parts of vehicles,
- 3 - `partsOfTyres` - in case the detected obstacles are parts of tyres,
- 4 - `bigObjects` - in case the detected obstacles are big objects,
- 5 - `fallenTrees` - in case the detected obstacles are fallen trees,
- 6 - `hubCaps` - in case the detected obstacles are hub caps,
- 7 - `waitingVehicles`- in case the detected obstacles are waiting vehicles.
- 8-255 - are reserved for future usage.
1689
1690
1691
1692
1693
1694
1695
1696
1697
1698
1699
1700
1701
1702
1703
1704
1705
1706
1707
1708
1709
1710
1711
1712
1713
1714
1715
1716
1717
1718
1719
1720
1721
**Categories**: Traffic information
**Revision**: _V1.3.1_
```asn1
HazardousLocation-ObstacleOnTheRoadSubCauseCode ::= INTEGER {
unavailable (0),
shedLoad (1),
partsOfVehicles (2),
partsOfTyres (3),
bigObjects (4),
fallenTrees (5),
hubCaps (6),
waitingVehicles (7)
} (0..255)
```
### <a name="HazardousLocation-SurfaceConditionSubCauseCode"></a>HazardousLocation-SurfaceConditionSubCauseCode
This DE represents the value of the sub cause code of the [**CauseCode**](#CauseCode) `hazardousLocation-SurfaceCondition`.
The value shall be set to:
- 0 - `unavailable` - in case further detailed information on the road surface condition is unavailable,
- 1 - `rockfalls` - in case rock falls are detected on the road surface,
- 2 - `earthquakeDamage`- in case the road surface is damaged by earthquake,
- 3 - `sewerCollapse` - in case of sewer collapse on the road surface,
- 4 - `subsidence` - in case road surface is damaged by subsidence,
- 5 - `snowDrifts` - in case road surface is damaged due to snow drift,
- 6 - `stormDamage` - in case road surface is damaged by strong storm,
- 7 - `burstPipe` - in case road surface is damaged due to pipe burst,
- 8 - `volcanoEruption` - in case road surface is damaged due to volcano eruption,
- 9 - `fallingIce` - in case road surface damage is due to falling ice,
- 10 - `fire` - in case there is fire on or near to the road surface.
- 11-255 - are reserved for future usage.
1724
1725
1726
1727
1728
1729
1730
1731
1732
1733
1734
1735
1736
1737
1738
1739
1740
1741
1742
1743
1744
1745
1746
**Categories**: Traffic information
**Revision**: _V1.3.1_
```asn1
HazardousLocation-SurfaceConditionSubCauseCode ::= INTEGER {
unavailable (0),
rockfalls (1),
earthquakeDamage (2),
sewerCollapse (3),
subsidence (4),
snowDrifts (5),
stormDamage (6),
burstPipe (7),
volcanoEruption (8),
fallingIce (9),
fire (10)
} (0..255)
```
### <a name="HeadingConfidence"></a>HeadingConfidence
This DE indicates the heading confidence value which represents the estimated absolute accuracy of a heading value with a confidence level of 95 %.
The value shall be set to:
- `n (n > 0 and n < 126)` if the confidence value is equal to or less than n x 0,1 degree and more than (n-1) x 0,1 degree,
- `126` if the confidence value is out of range, i.e. greater than 12,5 degrees,
- `127` if the confidence value information is not available.
**Unit**: _0,1 degree_
**Categories**: GeoReference information
**Revision**: _Description revised in V2.1.1_
>>>
NOTE: this DE is kept for backwards compatibility reasons only. It is recommended to use the [**Wgs84AngleConfidence**](#Wgs84AngleConfidence) instead.
HeadingConfidence ::= INTEGER {
outOfRange (126),
unavailable (127)
} (1..127)
```
### <a name="HeadingValue"></a>HeadingValue
This DE represents the orientation of the horizontal velocity vector with regards to the WGS84 north.
When the information is not available, the DE shall be set to 3 601. The value 3600 shall not be used.
Unit: 0,1 degree
Categories: GeoReference information
**Revision**: _Description revised in V2.1.1 (usage of value 3600 specified)_
>>>
NOTE: this DE is kept for backwards compatibility reasons only. It is recommended to use the [**Wgs84AngleValue**](#Wgs84AngleValue) instead.
HeadingValue ::= INTEGER {
wgs84North (0),
wgs84East (900),
wgs84South (1800),
wgs84West (2700),
doNotUse (3600),
unavailable (3601)
} (0..3601)
```
### <a name="HeightLonCarr"></a>HeightLonCarr
This DE represents the height of the left or right longitude carrier of vehicle from base to top (left or right carrier seen from vehicle
rear to front).
The value shall be set to:
- `n (n >= 1 and n < 99)` if the height information is equal to or less than n x 0,01 metre and more than (n-1) x 0,01 metre,
- `99` if the height is out of range, i.e. equal to or greater than 0,98 m,
- `100` if the height information is not available.
**Categories**: Vehicle information
**Revision**: _Description revised in V2.1.1 (the definition of 99 has changed slightly)_
```asn1
HeightLonCarr ::= INTEGER {
unavailable(100)
} (1..100)
```
### <a name="HumanPresenceOnTheRoadSubCauseCode"></a>HumanPresenceOnTheRoadSubCauseCode
This DE represents the value of the sub cause code of the [**CauseCode**](#CauseCode) `humanPresenceOnTheRoad`.
The value shall be set to:
- 0 - `unavailable` - in case further detailed information on human presence on the road is unavailable,
- 1 - `childrenOnRoadway` - in case children are detected on the road,
- 2 - `cyclistOnRoadway` - in case cyclist presence is detected on the road,
- 3 - `motorcyclistOnRoadway`- in case motorcyclist presence is detected on the road.
- 4-255 - are reserved for future usage.
**Categories**: Traffic information
**Revision**: _editorial revision in V2.1.1_
```asn1
HumanPresenceOnTheRoadSubCauseCode ::= INTEGER {
unavailable (0),
childrenOnRoadway (1),
cyclistOnRoadway (2),
motorcyclistOnRoadway (3)
} (0..255)
```
### <a name="HumanProblemSubCauseCode"></a>HumanProblemSubCauseCode
This DE represents the value of the sub cause codes of the [**CauseCode**](#CauseCode) "humanProblem".
The value shall be set to:
- 0 - `unavailable` - in case further detailed information on human health problem is unavailable,
- 1 - `glycemiaProblem`- in case human problem is due to glycaemia problem,
- 2 - `heartProblem` - in case human problem is due to heart problem.
1851
1852
1853
1854
1855
1856
1857
1858
1859
1860
1861
1862
1863
1864
1865
1866
1867
1868
1869
1870
1871
1872
1873
1874
1875
1876
1877
1878
1879
1880
1881
1882
1883
1884
1885
1886
1887
1888
1889
1890
1891
- 3-255 - reserved for future usage.
**Categories**: Traffic information
**Revision**: _V1.3.1_
```asn1
HumanProblemSubCauseCode ::= INTEGER {
unavailable (0),
glycemiaProblem (1),
heartProblem (2)
} (0..255)
```
### <a name="Identifier1B"></a>Identifier1B
This DE is a general identifier.
**Categories**: Basic information
**Revision**: _Created in V2.1.1_
```asn1
Identifier1B ::= INTEGER (0..255)
```
### <a name="Identifier2B"></a>Identifier2B
This DE is a general identifier.
**Categories**: Basic information
**Revision**: _Created in V2.1.1_
```asn1
Identifier2B ::= INTEGER (0..65535)
```
### <a name="InformationQuality"></a>InformationQuality
This DE represents the quality level of provided information.
The value shall be set to:
- `0` if the information is unavailable,
- `1` if the quality level is lowest,
- `n (n > 1 and n < 7)` if the quality level is n,
**Categories**: Basic information
**Revision**: _Editorial update in V2.1.1_
>>>
NOTE: Definition of quality level is out of scope of the present document.
>>>
```asn1
InformationQuality ::= INTEGER (0..7)
```
### <a name="InterferenceManagementZoneType"></a>InterferenceManagementZoneType
This DE defines the type of an interference management zone, so that an ITS-S can
assert the actions to do while passing by such zone (e.g. reduce the transmit power in case of a DSRC tolling station).
It is an extension of the type [**ProtectedZoneType**](#ProtectedZoneType).
The value shall be set to:
- 0 - `permanentCenDsrcTolling` - as specified in ETSI TS 102 792 [i.14],
- 1 - `temporaryCenDsrcTolling` - as specified in ETSI TS 102 792 [i.14],
- 2 - `unavailable` - default value. Set to 2 for backwards compatibility with DSRC tolling,
- 3 - `urbanRail` - as specified in ETSI TS 103 724 [i.13], clause 7,
- 4 - `satelliteStation` - as specified in ETSI TS 103 724 [i.13], clause 7,
- 5 - `fixedLinks` - as specified in ETSI TS 103 724 [i.13], clause 7.
**Categories**: Communication information
**Revision**: _Created in V2.1.1_
```asn1
InterferenceManagementZoneType ::= ENUMERATED {
permanentCenDsrcTolling (0),
temporaryCenDsrcTolling (1),
unavailable (2),
urbanRail (3),
satelliteStation (4),
fixedLinks (5),
...
}
```
### <a name="Iso3833VehicleType"></a>Iso3833VehicleType
This DE represents the vehicle type according to ISO 3833 [3].
A "term No" refers to the number of the corresponding term and its definition in ISO 3833.
The value shall be set to:
- 0 - `passengerCar` - term No 3.1.1
- 1 - `saloon` - term No 3.1.1.1 (sedan)
- 2 - `convertibleSaloon` - term No 3.1.1.2
- 3 - `pullmanSaloon` - term No 3.1.1.3
- 4 - `stationWagon` - term No 3.1.1.4
- 5 - `truckStationWagon` - term No 3.1.1.4.1
- 6 - `coupe` - term No 3.1.1.5 (coupe)
- 7 - `convertible` - term No 3.1.1.6 (open tourer, roadstar, spider)
- 8 - `multipurposePassengerCar` - term No 3.1.1.7
- 9 - `forwardControlPassengerCar`- term No 3.1.1.8
- 10 - `specialPassengerCar` - term No 3.1.1.9
1957
1958
1959
1960
1961
1962
1963
1964
1965
1966
1967
1968
1969
1970
1971
1972
1973
1974
1975
1976
1977
1978
1979
1980
1981
1982
1983
1984
1985
1986
1987
1988
1989
1990
1991
1992
1993
- 12 - `minibus` - term No 3.1.2.1
- 13 - `urbanBus` - term No 3.1.2.2
- 14 - `interurbanCoach` - term No 3.1.2.3
- 15 - `longDistanceCoach` - term No 3.1.2.4
- 16 - `articulatedBus` - term No 3.1.2.5
- 17 - `trolleyBus ` - term No 3.1.2.6
- 18 - `specialBus` - term No 3.1.2.7
- 19 - `commercialVehicle ` - term No 3.1.3
- 20 - `specialCommercialVehicle` - term No 3.1.3.1
- 21 - `specialVehicle ` - term No 3.1.4
- 22 - `trailingTowingVehicle ` - term No 3.1.5 (draw-bar tractor)
- 23 - `semiTrailerTowingVehicle` - term No 3.1.6 (fifth wheel tractor)
- 24 - `trailer` - term No 3.2.1
- 25 - `busTrailer` - term No 3.2.1.1
- 26 - `generalPurposeTrailer` - term No 3.2.1.2
- 27 - `caravan` - term No 3.2.1.3
- 28 - `specialTrailer` - term No 3.2.1.4
- 29 - `semiTrailer` - term No 3.2.2
- 30 - `busSemiTrailer ` - term No 3.2.2.1
- 31 - `generalPurposeSemiTrailer` - term No 3.2.2.2
- 32 - `specialSemiTrailer` - term No 3.2.2.3
- 33 - `roadTrain` - term No 3.3.1
- 34 - `passengerRoadTrain ` - term No 3.3.2
- 35 - `articulatedRoadTrain` - term No 3.3.3
- 36 - `doubleRoadTrain` - term No 3.3.4
- 37 - `compositeRoadTrain` - term No 3.3.5
- 38 - `specialRoadTrain` - term No 3.3.6
- 39 - `moped` - term No 3.4
- 40 - `motorCycle` - term No 3.5
- 41-255 - reserved for future use
**Categories**: Vehicle information
**Revision**: _Created in V2.1.1_
```asn1
Iso3833VehicleType ::= INTEGER {
passengerCar (0),
saloon (1),
convertibleSaloon (2),
pullmanSaloon (3),
stationWagon (4),
truckStationWagon (5),
coupe (6),