Commit c95290ac authored by garciay's avatar garciay

Add Marben UdpIp support

parent 9e6bd6fa
# Debug level - Authorized values: OFF, ALL, INFO, SEVERE
DEBUG_ENABLED=OFF
# Define the port/layer configuration for CAM
#camPort=BTP/GN/ETH
camPort=BTP/GN/UdpIpCSG
camPort=BTP/GN/ETH
#camPort=BTP/GN/UdpIpCSG
#camPort=BTP/GN/CSG
#camPort=BTP/GN/UdpIpMarben
# Define the port/layer configuration for DENM
#denmPort=BTP/GN/ETH
denmPort=BTP/GN/UdpIpCSG
denmPort=BTP/GN/ETH
#denmPort=BTP/GN/UdpIpCSG
#denmPort=BTP/GN/CSG
#denmPort=BTP/GN/UdpIpMarben
# Define the port/layer configuration for MAPEM-SPATEM
mapemSpatemPort=BTP/GN/ETH
#mapemSpatemPort=BTP/GN/CSG
......@@ -20,9 +22,10 @@ sremSsemPort=BTP/GN/ETH
# Define the port/layer configuration for BTP
btpPort=GN/ETH
# Define the port/layer configuration for GeoNetworking
#geoNetworkingPort=ETH
geoNetworkingPort=UdpIpCSG
geoNetworkingPort=ETH
#geoNetworkingPort=UdpIpCSG
#geoNetworkingPort=CSG
#geoNetworkingPort=UdpIpMarben
# Define the port/layer configuration for GeoNetworking over IPv6
ipv6OverGeoNetworkingPort=Debug
# Define the port/layer configuration for CALM FNTP
......@@ -32,19 +35,21 @@ ipv6OverGeoNetworkingPort=Debug
#fsapPort=FSAP/UdpIp
#fsapPort=FSAP/UdpIp
# Commsignia RSU/OBU Simulator
# Commsignia RSU and OBU Simulator
#UpperTesterSettings=10.200.1.101:12345
# Commsignia Wireless OBU
UpperTesterSettings=80.98.62.165:18502
#UpperTesterSettings=80.98.62.165:18502
# Savari/VPN
#UpperTesterSettings=192.168.20.153:1999
# Yogoko/VPN
#UpperTesterSettings=192.168.201.2:12345
# Home laptop
#UpperTesterSettings=192.168.1.53:12345
UpperTesterSettings=192.168.1.53:12345
# Marben Jupiter VM32G upper tester
#UpperTesterSettings=192.168.7.182:10005
# RSU simulator
#ConfigTesterSettings=10.200.1.102:12346
ConfigTesterSettings=10.200.1.102:12346
# Peer ITS station
#LinkLayer_Peer=001C6B0D0199
......@@ -60,9 +65,10 @@ LocalEthernetMAC=DC536045AF7E
#LocalEthernetMAC=0022191B7FDB
# G5 bridge connected on USB3/Ethernet
#LocalEthernetMAC=00E08F008855
# Post-mortem ATS execution mode
# Post-mortem ATS execution mode (G5 raw Ethernet only)
OfflineMode=false
PcapFile=pcap/vendor/Livorno 20160914-2 DENM Full packet.pcap
#PcapFile=pcap/vendor/Livorno 20160914-2 DENM Full packet.pcap
PcapFile=F:/FSCOM/ETSI/ITS/STF517_ITS_Valid_Conform_Frmwk.2016/ITS-CMS5 PreQ/Savari/TC_SEC_ITSS_SND_MSG_01_01_BV.pcap
# Start at time in seconds since 1970-01-01, e.g. 1421661427.233361
OffsetTime=0
# Define the Ethernet type value used by the IUT
......@@ -92,15 +98,21 @@ LinkLayer_NodeJ=001C6B0D010A
# Interval between each beacon sent by TS (ms)
TsBeaconInterval=1000
# Latitude of Test System
#Commsignia
TsLatitude=514744250
#Commsignia TsLatitude=435525450
#Yogoko TsLatitude=481210840
#Livorno TsLatitude=43551050
#Marben TsLatitude=436175790
#Livorno
TsLatitude=43551050
# Sofia-antipolis TsLatitude=436175790
# Longitude of Test System
#Commsignia
TsLongitude=56240550
# Yogoko TsLongitude=-16287930
#Livorno TsLongitude=10298730
#Commsignia TsLongitude=103008910
#Yogoko TsLongitude=-16287930
#Marben TsLongitude=70546480
#Livorno
TsLongitude=10298730
# Sofia-antipolis TsLongitude=70546480
# Secured mode status
UtSecuredMode=false
# Secured configuration identifier
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment