Add Marben UdpIp support

javasrc/tool/org/etsi/its/tool/elvior/res/ta.properties

 # Debug level - Authorized values: OFF, ALL, INFO, SEVERE
 DEBUG_ENABLED=OFF
 # Define the port/layer configuration for CAM
-#camPort=BTP/GN/ETH
-camPort=BTP/GN/UdpIpCSG
+camPort=BTP/GN/ETH
+#camPort=BTP/GN/UdpIpCSG
 #camPort=BTP/GN/CSG
+#camPort=BTP/GN/UdpIpMarben
 # Define the port/layer configuration for DENM
-#denmPort=BTP/GN/ETH
-denmPort=BTP/GN/UdpIpCSG
+denmPort=BTP/GN/ETH
+#denmPort=BTP/GN/UdpIpCSG
 #denmPort=BTP/GN/CSG
+#denmPort=BTP/GN/UdpIpMarben
 # Define the port/layer configuration for MAPEM-SPATEM
 mapemSpatemPort=BTP/GN/ETH
 #mapemSpatemPort=BTP/GN/CSG
@@ -20,9 +22,10 @@ sremSsemPort=BTP/GN/ETH
 # Define the port/layer configuration for BTP
 btpPort=GN/ETH
 # Define the port/layer configuration for GeoNetworking
-#geoNetworkingPort=ETH
-geoNetworkingPort=UdpIpCSG
+geoNetworkingPort=ETH
+#geoNetworkingPort=UdpIpCSG
 #geoNetworkingPort=CSG
+#geoNetworkingPort=UdpIpMarben
 # Define the port/layer configuration for GeoNetworking over IPv6
 ipv6OverGeoNetworkingPort=Debug
 # Define the port/layer configuration for CALM FNTP
@@ -32,19 +35,21 @@ ipv6OverGeoNetworkingPort=Debug
 #fsapPort=FSAP/UdpIp
 #fsapPort=FSAP/UdpIp
 
-# Commsignia RSU/OBU Simulator
+# Commsignia RSU and OBU Simulator
 #UpperTesterSettings=10.200.1.101:12345
 # Commsignia Wireless OBU
-UpperTesterSettings=80.98.62.165:18502
+#UpperTesterSettings=80.98.62.165:18502
 # Savari/VPN
 #UpperTesterSettings=192.168.20.153:1999
 # Yogoko/VPN
 #UpperTesterSettings=192.168.201.2:12345
 # Home laptop
-#UpperTesterSettings=192.168.1.53:12345
+UpperTesterSettings=192.168.1.53:12345
+# Marben Jupiter VM32G upper tester
+#UpperTesterSettings=192.168.7.182:10005
 
 # RSU simulator
-#ConfigTesterSettings=10.200.1.102:12346
+ConfigTesterSettings=10.200.1.102:12346
 
 # Peer ITS station
 #LinkLayer_Peer=001C6B0D0199
@@ -60,9 +65,10 @@ LocalEthernetMAC=DC536045AF7E
 #LocalEthernetMAC=0022191B7FDB
 # G5 bridge connected on USB3/Ethernet
 #LocalEthernetMAC=00E08F008855
-# Post-mortem ATS execution mode
+# Post-mortem ATS execution mode (G5 raw Ethernet only)
 OfflineMode=false
-PcapFile=pcap/vendor/Livorno 20160914-2 DENM Full packet.pcap
+#PcapFile=pcap/vendor/Livorno 20160914-2 DENM Full packet.pcap
+PcapFile=F:/FSCOM/ETSI/ITS/STF517_ITS_Valid_Conform_Frmwk.2016/ITS-CMS5 PreQ/Savari/TC_SEC_ITSS_SND_MSG_01_01_BV.pcap
 # Start at time in seconds since 1970-01-01, e.g. 1421661427.233361
 OffsetTime=0
 # Define the Ethernet type value used by the IUT
@@ -92,15 +98,21 @@ LinkLayer_NodeJ=001C6B0D010A
 # Interval between each beacon sent by TS (ms)
 TsBeaconInterval=1000
 # Latitude of Test System
-#Commsignia
-TsLatitude=514744250
+#Commsignia TsLatitude=435525450
 #Yogoko TsLatitude=481210840
-#Livorno TsLatitude=43551050
+#Marben TsLatitude=436175790
+#Livorno 
+TsLatitude=43551050
+# Sofia-antipolis TsLatitude=436175790
+
 # Longitude of Test System
-#Commsignia
-TsLongitude=56240550
-# Yogoko TsLongitude=-16287930
-#Livorno TsLongitude=10298730
+#Commsignia TsLongitude=103008910
+#Yogoko TsLongitude=-16287930
+#Marben TsLongitude=70546480
+#Livorno 
+TsLongitude=10298730
+# Sofia-antipolis TsLongitude=70546480
+
 # Secured mode status
 UtSecuredMode=false
 # Secured configuration identifier