Newer
Older
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
1024
* Ensure that the IUT
* on receipt of a LOCATION_REPORTING_CONTROL
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Request_Type
* containing an Event_Type
* indicating stop_change_of_service_cell
* containing a Report_Area
* indicating ECGI
* when UE changes to new cell
* sends LOCATION_REPORT
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-UTRAN_CGI
* containing a PLMN_Identity
* containing a Cell_Identity
* containing a TAI
* containing a PLMN_Identity
* containing a TAC
* containing a Request_Type
* containing a Event_Type
* containing a Report_Area.
* </pre>
*
* @reference ETSI TS 136 413 V13.4.0 Clause 8.11.1.2-2(1st dashed line) and 9.1.12.1 and 9.1.12.3 and 9.2.1.16,34,38
*/
testcase TC_S1AP_eNB_LRP_03() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
/**
* @desc Verify that the IUT can send a LOCATION REPORT_FAILURE_INDICATION.
* <pre>
* Pics Selection: PICS A.3/10.1 and A.3/10.3
* Ensure that the IUT
* on receipt of a LOCATION_REPORTING_CONTROL
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Request_Type
* containing an Event_Type
* containing a Report_Area
* sends LOCATION REPORT_FAILURE_INDICATION
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Cause
* indicating an appropriate cause value.
* </pre>
*
* @reference ETSI TS 136 413 V13.4.0 Clause 8.11.2.2-1 and 9.1.12.2
*/
testcase TC_S1AP_eNB_LRP_04() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of group Location_reporting_group
/**
* @desc Warning message transmission group
* @see ETSI DTS/INT-00135-2 Clause 5.2.2.1.12 Warning message transmission group
*/
group Warning_message_transmission_group {
/**
* @desc Verify that the IUT can successfully process all mandatory IEs in a WRITE-REPLACE_WARNING_REQUEST received and sends a WRITE-REPLACE_WARNING_RESPONSE.
* Ensure that the IUT
* on receipt of an WRITE-REPLACE_WARNING_REQUEST
* containing a Message_Identifier
* containing a Serial_Number
* containing a Repetition Period
* containing an Number_of_Broadcasts_Requested
* sends an WRITE-REPLACE_WARNING_RESPONSE
* containing a Serial_Number.
* </pre>
*
* @reference ETSI TS 136 413 V13.4.0 Clause 8.12.1.2-1 and 9.1.13.1 and 9.1.13.2
*/
testcase TC_S1AP_eNB_WTP_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
* @desc Verify that the IUT can successfully process all mandatory IEs in an KILL_REQUEST received and sends a KILL_RESPONSE.
* Ensure that the IUT
* on receipt of a KILL_REQUEST
* containing a Message_Identifier
* containing a Serial_Number
* sends sends a KILL_RESPONSE
* containing a Message_Identifier
* containing a Serial_Number.
* </pre>
*
* @reference ETSI TS 136 413 V13.4.0 Clause 8.12.2.2-1,3 and 9.1.13.3 and 9.1.13.4
*/
testcase TC_S1AP_eNB_WTP_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
/**
* @desc Verify that the IUT can send a PWS_RESTART_INDICATION to indicate a PWS Restart Indication procedure.
* <pre>
* Pics Selection: PICS A.3/11.3
* Ensure that the IUT
* to indicate a PWS Restart Indication procedure
* sends a PWS_RESTART_INDICATION
* containing an E-CGI_List_for_Restart
* indicating a valid list of E-CGI
* containing a TAI_List_for_Restart
* indicating a valid list of eNB identifier
* containing an Emergency_Area_ID_List_for_Restart
* indicating an empty list.
* </pre>
*
* @reference ETSI TS 136 413 V13.4.0 Clause 8.12.3.2 and 9.1.13.5
*/
testcase TC_S1AP_eNB_WTP_03() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
/**
* @desc Verify that the IUT can send a PWS_FAILURE_INDICATION to indicate PWS Failure Indication procedure.
* <pre>
* Pics Selection: PICS A.3/11.4
* Ensure that the IUT
* to indicate a PWS Failure Indication procedure
* sends a PWS_FAILURE_INDICATION
* containing an PWS failed E-CGI List
* indicating a valid list of E-CGI
* @reference ETSI TS 136 413 V13.4.0 Clause 8.12.4.2 and 9.1.13.6
*/
testcase TC_S1AP_eNB_WTP_04() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of group Warning_message_transmission_group
/**
* @desc eNB direct information transfer group
* @see ETSI DTS/INT-00135-2 Clause 5.2.2.1.13 eNB direct information transfer group
*/
group ENB_direct_information_transfer_group {
/**
* @desc Verify that the IUT can send an eNB_DIRECT_INFORMATION_TRANSFER to indicate an eNB Direct Information Transfer procedure.
* <pre>
* Pics Selection: PICS A.4/12
* Ensure that the IUT
* to indicate an eNB direct information Transfer procedure,
* sends an eNB_DIRECT_INFORMATION_TRANSFER
* containing an Inter-system_Information_Transfer_Type
* containing a RIM
* containing a RIM_Transfer
* containing a RIM_Information
* containing a RIM_Routing_Address.
* </pre>
*
* @reference ETSI TS 136 413 V13.4.0 Clause 8.13.2.1 and 9.1.14 and 9.2.3.23
*/
testcase TC_S1AP_eNB_EIT_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
1315
1316
1317
1318
1319
1320
1321
1322
1323
1324
1325
1326
1327
1328
1329
1330
1331
1332
1333
1334
1335
1336
1337
1338
1339
1340
} // End of group ENB_direct_information_transfer_group
/**
* @desc eNB configuration transfer group
* @see ETSI DTS/INT-00135-2 Clause 5.2.2.1.15 eNB configuration transfer group
*/
group ENB_configuration_transfer_group {
/**
* @desc Verify that the IUT can send an eNB_CONFIGURATION_TRANSFER to indicate an eNB Configuration Transfer procedure.
* <pre>
* Pics Selection: PICS A.4/14
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an eNB Configuration Transfer procedure,
* sends an eNB_CONFIGURATION_TRANSFER
* containing a SON_Configuration_Transfer
* containing a Target_eNB-ID
* containing a Source_eNB-ID
* containing a SON_Information.
* containing a SON_Information_Request
* indicating X2TNL_Configuration_Info
* containing an X2_TNL_Configuration_Info.
* </pre>
*
* @reference ETSI TS 136 413 V13.4.0 Clause 8.15.2.1 and 9.1.16
*/
testcase TC_S1AP_eNB_ECT_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component configuration
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
1366
1367
1368
1369
1370
1371
1372
1373
1374
1375
1376
1377
1378
1379
1380
1381
1382
1383
1384
1385
1386
1387
1388
1389
1390
} // End of group ENB_configuration_transfer_group
/**
* @desc LPPa transport group
* @see ETSI DTS/INT-00135-2 Clause 5.2.2.1.17 LPPa transport group
*/
group LPPa_transport_group {
/**
* @desc Verify that the IUT can send a UPLINK_UE_ASSOCIATED_LPPA_TRANSPORT to indicate a LPPa Transport procedure
* using a UE associated signalling.
* <pre>
* Pics Selection: PICS A.3/16.2
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a LPPa Transport procedure using a UE associated signalling,
* sends a UPLINK_UE_ASSOCIATED_LPPA_TRANSPORT
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Routing_ID
* indicating a valid routing identifier value
* containing an LPPa-PDU.
* </pre>
*
* @reference ETSI TS 136 413 V13.4.0 Clause 8.17.2.2 and 9.1.19.2
*/
testcase TC_S1AP_eNB_LPP_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component configuration
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
/**
* @desc Verify that the IUT can send a UPLINK_UE_ASSOCIATED_LPPA_TRANSPORT to indicate a LPPa Transport procedure
* using a Non-UE associated signalling.
* <pre>
* Pics Selection: PICS A.3/16.4
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a LPPa Transport procedure using a UE associated signalling,
* sends a UPLINK_UE_ASSOCIATED_LPPA_TRANSPORT
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing a Routing_ID
* indicating a valid routing identifier value
* containing an LPPa-PDU.
* </pre>
*
* @reference ETSI TS 136 413 V13.4.0 Clause 8.17.2.4 and 9.1.19.4
*/
testcase TC_S1AP_eNB_LPP_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_enb;
// Test control
if (not PICS_S1AP_eNB_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_eNB_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component configuration
f_cf_S1AP_eNB_Up(v_s1ap_enb);
// Start
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of group LPPa_transport_group
group MME_Role { // TODO Review all preamble action: E-RAB Setup is exchanged for MME role, shall not be f_rABSetupRequest
/**
* @desc E-RAB management group
* @see ETSI DTS/INT-00135-2 Clause 5.2.2.2.2 E-RAB management group
*/
/**
* @desc Verify that the IUT can send an E-RAB_SETUP_REQUEST with at least one E-RAB IE to indicate an E-RAB Setup procedure.
* <pre>
* Pics Selection: PICS A.4/1.1
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an E-RAB Setup procedure,
* sends an E-RAB_SETUP_REQUEST
* containing an MME_UE_S1AP_ID
* containing an eNB_UE_S1AP_ID
* containing an E-RAB_to_be_Setup_List
* containing an E-RAB_to_be_Setup Item 1
* containing an E-RAB_ID
* containing an E-RAB_Level_QoS_Parameters
* containing a Transport_Layer_Address
* containing a GTP-TEID
* containing a NAS-PDU.
* </pre>
*
* @reference ETSI TS 136 413 V13.4.0 Clause 8.2.1.2 and 9.1.3.1
*/
testcase TC_S1AP_MME_RAB_01() runs on S1AP system TestAdapter {
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
v_s1ap_mme.start(f_TC_S1AP_MME_RAB_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
} // End of testcase TC_S1AP_MME_RAB_01
} // End of group ERAB_management_group
1518
1519
1520
1521
1522
1523
1524
1525
1526
1527
1528
1529
1530
1531
1532
1533
1534
1535
1536
1537
1538
1539
1540
1541
1542
1543
1544
1545
1546
1547
1548
1549
1550
1551
1552
1553
1554
1555
1556
1557
1558
1559
1560
1561
1562
1563
1564
1565
1566
1567
1568
1569
1570
1571
1572
1573
1574
1575
1576
1577
1578
1579
1580
1581
1582
1583
1584
1585
1586
1587
1588
1589
1590
1591
1592
1593
1594
1595
1596
1597
1598
1599
1600
1601
1602
1603
/**
* @desc NAS transport group
* @see ETSI DTS/INT-00135-2 Clause 5.2.2.2.6 NAS transport group
*/
group NAS_transport_group {
/**
* @desc Verify that the IUT can send a DOWNLINK_NAS_TRANSPORT to indicate an ongoing NAS Transport procedure.
* <pre>
* Pics Selection: A.4/5.2
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an ongoing NAS Transport procedure
* sends a DOWNLINK_NAS_TRANSPORT
* containing an MME UE S1AP ID
* containing an eNB_UE_S1AP_ID
* containing a NAS-PDU.
* </pre>
*
* @see ETSI DTS/INT-00135-2 TP_S1AP_MME_NAS_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.6.2.2¶1 and 9.1.7.2
*/
testcase TC_S1AP_MME_NAS_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_NAS_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_NAS_01
/**
* @desc Verify that the IUT can send a REROUTE_NAS_REQUEST to indicate a Reroute NAS Request procedure.
* <pre>
* Pics Selection: A.4/5.5
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate a Reroute NAS Request procedure
* sends a REROUTE_NAS_REQUEST
* containing an MME UE S1AP ID
* containing a S1_Message
* containing an MME_Group_ID.
* </pre>
*
* @see ETSI DTS/INT-00135-2 TP_S1AP_MME_NAS_02
* @reference ETSI TS 136 413 V13.4.0 Clause 8.6.2.2¶1 and 9.1.7.2
*/
testcase TC_S1AP_MME_NAS_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_NAS_02());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_NAS_02
} // End of group NAS_transport_group
/**
* @desc Management group
* @see ETSI DTS/INT-00135-2 Clause 5.2.2.2.7 Management group
*/
group Management_group {
/**
* @desc Verify that the IUT can send a RESET to indicate a Reset procedure initiated from the MME.
* <pre>
* Pics Selection: A.4/6.1.2
1615
1616
1617
1618
1619
1620
1621
1622
1623
1624
1625
1626
1627
1628
1629
1630
1631
1632
1633
1634
1635
1636
1637
1638
1639
1640
1641
1642
1643
1644
1645
1646
1647
1648
1649
1650
1651
* Ensure that the IUT
* to indicate a Reset procedure initiated from the MME
* sends a RESET
* containing a Cause
* indicating an appropriate cause value
* containing a Reset_Type
* containing a S1_Interface
* indicating a value ‘Reset_all’.
* </pre>
*
* @see ETSI DTS/INT-00135-2 TP_S1AP_MME_MNP_01
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.1.2.1¶2 and 9.1.8.1 and 9.1.8.2
*/
testcase TC_S1AP_MME_MNP_01() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MNP_01());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MNP_01
/**
* @desc Verify that the IUT can send process successfully all mandatory IEs in a RESET and sends a RESET_ACKNOWLEDGE
* <pre>
* Pics Selection: A.4/6.1.1
* Ensure that the IUT
* on receipt of a RESET
* containing a Cause
* indicating an appropriate cause value
* containing a Reset_Type
* containing an S1_Interface
* indicating value ‘Reset_all’
* sends a RESET_ACKNOWLEDGE
* containing a UE-associated_logical_S1-connection_list.
* </pre>
*
* @see ETSI DTS/INT-00135-2 TP_S1AP_MME_MNP_02
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.1.2.1¶2 and 9.1.8.1 and 9.1.8.2
1670
1671
1672
1673
1674
1675
1676
1677
1678
1679
1680
1681
1682
1683
1684
1685
1686
1687
1688
1689
1690
1691
1692
1693
*/
testcase TC_S1AP_MME_MNP_02() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MNP_02());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MNP_02
* @desc Verify that the IUT can successfully all mandatory IEs in a RESET and sends a RESET_ACKNOWLEDGE
1696
1697
1698
1699
1700
1701
1702
1703
1704
1705
1706
1707
1708
1709
1710
1711
1712
1713
1714
1715
1716
1717
1718
1719
1720
1721
1722
1723
1724
1725
1726
1727
1728
1729
1730
1731
1732
1733
1734
1735
1736
1737
1738
1739
1740
1741
1742
1743
1744
1745
1746
1747
1748
1749
1750
1751
1752
1753
1754
1755
1756
1757
1758
1759
1760
1761
1762
1763
1764
1765
1766
1767
1768
1769
1770
1771
1772
1773
1774
1775
1776
* due to a Reset procedure in case of Abnormal Condition at the EPC.
* <pre>
* Pics Selection: A.4/6.1.1
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of a RESET
* containing a Cause
* indicating an appropriate cause value
* containing a Reset_Type
* containing a Part_of_S1_interface
* indicating an empty ‘UE-associated_logical_S1-connection’
* sends a RESET_ACKNOWLEDGE
* containing a UE-associated_logical_S1-connection_list
* indicating an empty ‘UE-associated_logical_S1-connection’.
* </pre>
*
* @see ETSI DTS/INT-00135-2 TP_S1AP_MME_MNP_03
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.1.3.2¶1 and 9.1.8.1 and 9.1.8.2
*/
testcase TC_S1AP_MME_MNP_03() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MNP_03());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MNP_03
/**
* @desc Verify that the IUT can send a RESET to indicate a Reset procedure initiated from the eNB.
* <pre>
* Pics Selection: A.4/6.2.2
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an Error Indication procedure
* sends an ERROR_INDICATION
* (containing a Cause
* or containing a Criticality_Diagnostics).
* </pre>
*
* @see ETSI DTS/INT-00135-2 TP_S1AP_MME_MNP_04
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.1.2.1¶2 and 9.1.8.1 and 9.1.8.2
*/
testcase TC_S1AP_MME_MNP_04() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MNP_04());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MNP_04
/**
* @desc Verify that the IUT can process all mandatory IEs in a S1_SETUP_REQUEST and
* sends a S1_SETUP_RESPONSE to indicate a S1 Setup procedure.
* <pre>
* Pics Selection: A.4/6.3
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of a S1_SETUP_REQUEST
1784
1785
1786
1787
1788
1789
1790
1791
1792
1793
1794
1795
1796
1797
1798
1799
1800
1801
1802
1803
1804
1805
1806
1807
1808
1809
1810
1811
1812
1813
1814
1815
1816
* containing a Global_eNB_ID
* containing a Supported_TAs
* containing a TAC
* containing a Default_Paging_DRX
* sends a S1_SETUP_RESPONSE.
* </pre>
*
* @see ETSI DTS/INT-00135-2 TP_S1AP_MME_MNP_05
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.3.2¶1 and 9.1.8.4 and 9.1.8.5
*/
testcase TC_S1AP_MME_MNP_05() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MNP_05());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MNP_05
1817
1818
1819
1820
1821
1822
1823
1824
1825
1826
1827
1828
1829
1830
1831
1832
1833
1834
1835
1836
1837
1838
1839
1840
1841
1842
1843
1844
1845
1846
1847
1848
1849
1850
1851
1852
1853
1854
1855
1856
1857
1858
1859
1860
1861
1862
1863
1864
1865
1866
1867
1868
1869
1870
1871
1872
1873
1874
1875
1876
1877
1878
1879
1880
1881
1882
1883
1884
1885
1886
1887
1888
1889
1890
1891
1892
1893
1894
1895
1896
1897
1898
1899
1900
1901
1902
1903
1904
1905
1906
1907
1908
1909
1910
1911
1912
1913
1914
1915
1916
1917
1918
1919
1920
1921
1922
1923
1924
1925
1926
1927
1928
1929
1930
1931
1932
1933
1934
1935
1936
1937
1938
1939
1940
1941
1942
1943
1944
1945
1946
1947
1948
1949
1950
1951
1952
1953
1954
1955
1956
1957
1958
1959
1960
1961
1962
1963
1964
1965
1966
1967
1968
1969
1970
1971
1972
1973
1974
1975
1976
1977
1978
1979
1980
1981
1982
1983
1984
1985
1986
1987
1988
1989
1990
1991
1992
1993
1994
1995
1996
1997
1998
1999
2000
/**
* @desc Verify that the IUT can process all mandatory IEs in a S1_SETUP_REQUEST and
* sends a S1_SETUP_FAILURE to indicate an invalid S1 Setup procedure due to an unknown PLMN identities.
* <pre>
* Pics Selection: A.4/6.3
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of a S1_SETUP_REQUEST
* containing a Global_eNB_ID
* containing a Supported_TAs
* containing a TAC
* containing a Broadcast_PLMNs
* indicating at least one unknown PLMN identity
* sends a S1_SETUP_FAILURE
* containing a Cause
* indicating the cause value 'Unknown PLMN'.
* </pre>
*
* @see ETSI DTS/INT-00135-2 TP_S1AP_MME_MNP_06
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.3.2¶1 and 9.1.8.4 and 9.1.8.6
*/
testcase TC_S1AP_MME_MNP_06() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MNP_06());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MNP_06
/**
* @desc Verify that the IUT can process all mandatory IEs in an ENB_CONFIGURATION_UPDATE and
* sends an ENB_CONFIGURATION_UPDATE_ACKNOWLEDGE to indicate an eNB Configuration Update procedure.
* <pre>
* Pics Selection: A.4/6.4
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of an ENB_CONFIGURATION_UPDATE
* containing a Global_eNB_ID
* containing a Supported_TAs
* containing a TAC
* sends an MME_CONFIGURATION_UPDATE_ACKNOWLEDGE.
* </pre>
*
* @see ETSI DTS/INT-00135-2 TP_S1AP_MME_MNP_07
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.4.2¶1 and 9.1.8.7 and 9.1.8.8
*/
testcase TC_S1AP_MME_MNP_07() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MNP_07());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MNP_07
/**
* @desc Verify that the IUT can process all mandatory IEs in an ENB_CONFIGURATION_UPDATE and
* sends an ENB_CONFIGURATION_UPDATE_FAILURE to indicate an invalid eNB Configuration Update procedure due to an invalid Global eNB identifier.
* <pre>
* Pics Selection: A.4/6.4
* Configuration: CF_S1-MME
* Ensure that the IUT
* on receipt of an ENB_CONFIGURATION_UPDATE
* containing a Global_eNB_ID
* indicating invalid value
* sends an ENB_CONFIGURATION_UPDATE_FAILURE
* containing a Cause
* indicating an appropriate cause value.
* </pre>
*
* @see ETSI DTS/INT-00135-2 TP_S1AP_MME_MNP_08
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.3.2¶1 and 9.1.8.7 and 9.1.8.9
*/
testcase TC_S1AP_MME_MNP_08() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MNP_08());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MNP_08
/**
* @desc Verify that the IUT can send an ENB_CONFIGURATION_UPDATE to indicate an eNB Configuration Update procedure.
* <pre>
* Pics Selection: A.4/6.5
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an eNB Configuration Update procedure
* sends an ENB_CONFIGURATION_UPDATE
* containing a Global_eNB_ID
* containing a Supported_TAs
* containing a TAC.
* </pre>
*
* @see ETSI DTS/INT-00135-2 TP_S1AP_MME_MNP_09
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.4.2¶1 and 9.1.8.10
*/
testcase TC_S1AP_MME_MNP_09() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {
log("*** " & __SCOPE__ & ": ERROR: 'PICS_S1AP_MME_IUT' shall be set to true for executing the TC. ***");
stop;
}
// Test component direct information
f_cf_S1AP_MME_Up(v_s1ap_mme);
// Start
v_s1ap_mme.start(f_TC_S1AP_MME_MNP_09());
// synchronize PTC on 1 sychronization points
f_serverSyncNClientsAndStop(1, {c_prDone, c_tbDone, c_poDone});
f_cf_Down();
} // End of testcase TC_S1AP_MME_MNP_09
/**
* @desc Verify that the IUT can send an OVERLOAD_START to indicate an Overload Start procedure.
* <pre>
* Pics Selection: A.4/6.6
* Configuration: CF_S1-MME
* Ensure that the IUT
* to indicate an Overload Start procedure
* sends an OVERLOAD_START
* containing an Overload_Response.
* </pre>
*
* @see ETSI DTS/INT-00135-2 TP_S1AP_MME_MNP_10
* @reference ETSI TS 136 413 V13.4.0 Clause 8.7.6.2¶1 and 9.1.8.13
*/
testcase TC_S1AP_MME_MNP_10() runs on S1AP system TestAdapter {
// Local variables
var S1AP v_s1ap_mme;
// Test control
if (not PICS_S1AP_MME_IUT) {