temporarily higher speeds than requested, but the given limiting is considered
"over time" and is an average

(http://curl.haxx.se/bug/view.cgi?id=1603712) which is about connections
getting cut off prematurely when --limit-rate is used. While I found no such
problems in my tests nor in my reading of the code, I found that the
--limit-rate code was severly flawed (since it was moved into the lib, since
7.15.5) when used with the easy interface and it didn't work as documented so
I reworked it somewhat and now it works for my tests.

passing a curl_off_t argument to the Curl_read_rewind() function which takes
an size_t argument. Curl_read_rewind() also had debug code left in it and it
was put in a different source file with no good reason when only used from
one single spot.

no code present in the library that receives the option. Since it was not
possible to use, we know that no current users exist and thus we simply
removed it from the docs and made the code always use the default path of
the code.

(http://curl.haxx.se/bug/view.cgi?id=1604956) which identified setting
CURLOPT_MAXCONNECTS to zero caused libcurl to SIGSEGV. Starting now, libcurl
will always internally use no less than 1 entry in the connection cache.

Curl_done()

use gmtime_r

(http://curl.haxx.se/bug/view.cgi?id=1230118) curl_getdate() did not work
properly for all input dates on Windows. It was mostly seen on some TZ time
zones using DST. Luckily, Martin also provided a fix.

(http://curl.haxx.se/bug/view.cgi?id=1600447) in which he noted that active
FTP connections don't work with the multi interface. The problem is here that
the multi interface state machine has a state during which it can wait for the
data connection to connect, but the active connection is not done in the same
step in the sequence as the passive one is so it doesn't quite work for
active. The active FTP code still use a blocking function to allow the remote
server to connect.

The fix (work-around is a better word) for this problem is to set the
boolean prematurely that the data connection is completed, so that the "wait
for connect" phase ends at once.

HTTP upload was disconnected:

"What appears to be happening is that my system (Linux 2.6.17 and 2.6.13) is
setting *only* POLLHUP on poll() when the conditions in my previous mail
occur. As you can see, select.c:Curl_select() does not check for POLLHUP. So
basically what was happening, is poll() was returning immediately (with
POLLHUP set), but when Curl_select() looked at the bits, neither POLLERR or
POLLOUT was set. This still caused Curl_readwrite() to be called, which
quickly returned. Then the transfer() loop kept continuing at full speed
forever."

a warning output if no OpenSSL was found

header in a third, not suppported by libcurl, format and we agreed that we
could make the parser more forgiving to accept all the three found
variations.

holding the conn->data value

responded with a single status line and no headers nor body. Starting now, a
HTTP response on a persistent connection (i.e not set to be closed after the
response has been taken care of) must have Content-Length or chunked
encoding set, or libcurl will simply assume that there is no body.

To my horror I learned that we had no less than 57(!) test cases that did bad
HTTP responses like this, and even the test http server (sws) responded badly
when queried by the test system if it is the test system. So although the
actual fix for the problem was tiny, going through all the newly failing test
cases got really painful and boring.

as appropriate for platforms that don't have autotools support

struct, and there are domain/search entries in /etc/resolv.conf, the domains
of the options struct will be overridden.

defining HAVE_SIGNAL_H if the header is available.

Added a check in configure that tests if the sig_atomic_t type is
available, defining HAVE_SIG_ATOMIC_T if it is available. Providing
a suitable default in setup_once.h if not available.

Added a check in configure that tests if the sig_atomic_t type is
already defined as volatile, defining HAVE_SIG_ATOMIC_T_VOLATILE
if it is available and already defined as volatile.

This is done to back out changes done in revisions 1.77 and 1.75

This is done to back out changes done from revisions 1.213 to 1.217

This is done to back out changes done from revisions 1.6 to 1.10