# In this section you can specify parameters that are passed to Test Ports.
# CAM Layer
# next_header : btpA|btpB (overwrite BTP.type)
# header_type : tsb|gbc
# header_sub_type : sh (single hop)
# DENM Layer
# next_header : btpA|btpB (overwrite BTP.type)
# header_type : tsb|gbc
# BTP Layer
# type : btpA|btpB
# destination port: dst_port
# source port : src_port
# device_mode : Set to 1 if the layer shall encapsulate upper layer PDU
# device_mode : Set to 1 if the layer shall encapsulate upper layer PDU
# GN Layer
# its_aid : ITS AID as defined by ETSI TS 102 965 V1.2.1. Default: 141
# ll_address : GeoNetworking address of the Test System
# latitude : Latitude of the Test System
# longitude : Kongitude of the Test System
# beaconing : Set to 1 if the Test System shall start beaconing
# Beaconning timer expiry: Expiry (ms)
# device_mode : Set to 1 if the layer shall encapsulate upper layer PDU
# secured_mode : Set to 1 if message exchanges shall be signed
# encrypted_mode : Set to 1 if message exchanges shall be encrypted
# NOTE: For signed & encrypted message exchanges, both secured_mode and encrypted_mode shall be set to 1
# certificate : Certificate identifier the Test Adapter shall use
# secure_db_path : Path to the certificates and keys storage location
# hash : Hash algorithm to be used when secured mode is set
# Authorized values are SHA-256 or SHA-384
# Default: SHA-256
# signature : Signature algorithm to be used when secured mode is set
# Authorized values are NISTP-256, BP-256 and BP-384
# Default: NISTP-256
# cypher : Cyphering algorithm to be used when secured mode is set
# Ethernet layer
# mac_src :Source MAC address
# mac_bc :Broadcast address
# eth_type : Ethernet type
# Commsignia layer
# mac_src : Device MAC address, used to discard packets
# To indicate no filering, use the value 000000000000
# mac_bc : Broadcast address
# eth_type : Ethernet type, used to discard packets
# target_host : Device address
# target_port : Device port
# source_port : Test System port
# interface_id: Interface id, used to discard packets
# tx_power : TX power (dB)
# UDP layer (IP/UDP based on Pcap)
# dst_ip : destination IPv4 address (aa.bb.cc.dd)
# dst_port: destination port
# src_ip : source IPv4 address (aa.bb.cc.dd)
# src_port: source port
# Pcap layer
# mac_src : Source MAC address, used to exclude from capture the acket sent by the Test System
# filter : Pcap filter (compliant with tcpdump syntax)
# Online mode:
# nic: Local NIC
# If set, online mode is used
# Offline mode (nic is present but not set):
# file : File to read
# frame_offset: Frame offset, used to skip packets with frame number < frame_offset
# time_offset : Time offset, used to skip packets with time offset < time_offset
# save_mode : 1 to save sent packet, 0 otherwise
# Single GeoNetworking component port
system.geoNetworkingPort.params := "GN(ll_address=4C5E0C14D2EB,latitude=43551050,longitude=10298730,beaconing=0,device_mode=0,expiry=500,secured_mode=1,certificate=CERT_TS_A_AT,sec_db_path=/home/ubuntu/tmp/test_01)/ETH(mac_src=0800275e8e00,mac_bc=FFFFFFFFFFFF,eth_type=8947)/PCAP(mac_src=0800275e8e00,nic=enp0s8,filter=and ether proto 0x8947)"
# UpperTester port based on UDP
#system.utPort.params := "UT/UDP(dst_ip=192.168.56.1,dst_port=12346,src_ip=192.168.156.4,src_port=12345)/ETH(mac_src=026f8338c1e5,mac_dst=0A0027000011,eth_type=0800)/PCAP(mac_src=0800275e8e00,nic=enp0s8,filter=udp port 12346)"
# Config port based on UDP
system.cfPort.params := "CF(ut=cam)/UDP(dst_ip=192.168.0.253,dst_port=12345,src_ip=192.168.0.250,src_port=12345)/ETH(mac_src=0800275e8e00,mac_dst=0800275c4958,eth_type=0800)/PCAP(mac_src=0800275e8e00,nic=enp0s8,filter=and udp port 12345)"
[EXECUTE]
ItsRSUsSimulator_TestCases.TC_RSUSIMU_BV_01
[MAIN_CONTROLLER]
# The options herein control the behavior of MC.
KillTimer := 10.0
TCPPort := 0
LocalAddress := 127.0.0.1
TCPPort := 12000
NumHCs := 1
[MODULE_PARAMETERS]
# This section shall contain the values of all parameters that are defined in your TTCN-3 modules.
