Loading docs/curl.1 +20 −10 Original line number Diff line number Diff line Loading @@ -292,6 +292,10 @@ traditional PORT command. Since curl 7.19.0, \fB--eprt\fP can be used to explicitly enable EPRT again and \fB--no-eprt\fP is an alias for \fB--disable-eprt\fP. Disabling EPRT only changes the active behavior. If you want to switch to passive mode you need to not use \fI-P/--ftp-port\fP or force it with \fI--ftp-pasv\fP. .IP "--disable-epsv" (FTP) Tell curl to disable the use of the EPSV command when doing passive FTP transfers. Curl will normally always first attempt to use EPSV before PASV, Loading @@ -299,6 +303,9 @@ but with this option, it will not try using EPSV. Since curl 7.19.0, \fB--epsv\fP can be used to explicitly enable EPRT again and \fB--no-epsv\fP is an alias for \fB--disable-epsv\fP. Disabling EPSV only changes the passive behavior. If you want to switch to active mode you need to use \fI-P/--ftp-port\fP. .IP "-D/--dump-header <file>" Write the protocol headers to the specified file. Loading Loading @@ -421,13 +428,16 @@ compliant than 'nocwd' but without the full penalty of 'multicwd'. .RE (Added in 7.15.1) .IP "--ftp-pasv" (FTP) Use PASV when transferring. PASV is the internal default behavior, but using this option can be used to override a previous --ftp-port option. (Added in 7.11.0) (FTP) Use passive mode for the data conection. Passive is the internal default behavior, but using this option can be used to override a previous \fI-P/-ftp-port\fP option. (Added in 7.11.0) If this option is used several times, the following occurrences make no difference. Undoing an enforced PASV really isn't doable but you must then instead enforce the correct EPRT again. difference. Undoing an enforced passive really isn't doable but you must then instead enforce the correct \fI-P/--ftp-port\fP again. Passive mode means that curl will try the EPSV command first and then PASV, unless \fI--disable-epsv\fP is used. .IP "--ftp-alternative-to-user <command>" (FTP) If authenticating with the USER and PASS commands fails, send this command. When connecting to Tumbleweed's Secure Transport server over FTPS Loading Loading @@ -922,11 +932,11 @@ separate file. If this option is used several times, the last one will be used. .IP "-P/--ftp-port <address>" (FTP) Reverses the initiator/listener roles when connecting with FTP. This switch makes Curl use the PORT command instead of PASV. In practice, PORT tells the server to connect to the client's specified address and port, while PASV asks the server for an IP address and port to connect to. <address> should be one of: (FTP) Reverses the default initiator/listener roles when connecting with FTP. This switch makes curl use active mode. In practice, curl then tells the server to connect back to the client's specified address and port, while passive mode asks the server to setup an IP address and port for it to connect to. <address> should be one of: .RS .IP interface i.e "eth0" to specify which interface's IP address you want to use (Unix only) Loading Loading
docs/curl.1 +20 −10 Original line number Diff line number Diff line Loading @@ -292,6 +292,10 @@ traditional PORT command. Since curl 7.19.0, \fB--eprt\fP can be used to explicitly enable EPRT again and \fB--no-eprt\fP is an alias for \fB--disable-eprt\fP. Disabling EPRT only changes the active behavior. If you want to switch to passive mode you need to not use \fI-P/--ftp-port\fP or force it with \fI--ftp-pasv\fP. .IP "--disable-epsv" (FTP) Tell curl to disable the use of the EPSV command when doing passive FTP transfers. Curl will normally always first attempt to use EPSV before PASV, Loading @@ -299,6 +303,9 @@ but with this option, it will not try using EPSV. Since curl 7.19.0, \fB--epsv\fP can be used to explicitly enable EPRT again and \fB--no-epsv\fP is an alias for \fB--disable-epsv\fP. Disabling EPSV only changes the passive behavior. If you want to switch to active mode you need to use \fI-P/--ftp-port\fP. .IP "-D/--dump-header <file>" Write the protocol headers to the specified file. Loading Loading @@ -421,13 +428,16 @@ compliant than 'nocwd' but without the full penalty of 'multicwd'. .RE (Added in 7.15.1) .IP "--ftp-pasv" (FTP) Use PASV when transferring. PASV is the internal default behavior, but using this option can be used to override a previous --ftp-port option. (Added in 7.11.0) (FTP) Use passive mode for the data conection. Passive is the internal default behavior, but using this option can be used to override a previous \fI-P/-ftp-port\fP option. (Added in 7.11.0) If this option is used several times, the following occurrences make no difference. Undoing an enforced PASV really isn't doable but you must then instead enforce the correct EPRT again. difference. Undoing an enforced passive really isn't doable but you must then instead enforce the correct \fI-P/--ftp-port\fP again. Passive mode means that curl will try the EPSV command first and then PASV, unless \fI--disable-epsv\fP is used. .IP "--ftp-alternative-to-user <command>" (FTP) If authenticating with the USER and PASS commands fails, send this command. When connecting to Tumbleweed's Secure Transport server over FTPS Loading Loading @@ -922,11 +932,11 @@ separate file. If this option is used several times, the last one will be used. .IP "-P/--ftp-port <address>" (FTP) Reverses the initiator/listener roles when connecting with FTP. This switch makes Curl use the PORT command instead of PASV. In practice, PORT tells the server to connect to the client's specified address and port, while PASV asks the server for an IP address and port to connect to. <address> should be one of: (FTP) Reverses the default initiator/listener roles when connecting with FTP. This switch makes curl use active mode. In practice, curl then tells the server to connect back to the client's specified address and port, while passive mode asks the server to setup an IP address and port for it to connect to. <address> should be one of: .RS .IP interface i.e "eth0" to specify which interface's IP address you want to use (Unix only) Loading
