Newer
Older
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
=pod
=head1 NAME
SSL_get_error - obtain result code for TLS/SSL I/O operation
=head1 SYNOPSIS
#include <openssl/ssl.h>
int SSL_get_error(const SSL *ssl, int ret);
=head1 DESCRIPTION
SSL_get_error() returns a result code (suitable for the C "switch"
statement) for a preceding call to SSL_connect(), SSL_accept(), SSL_do_handshake(),
SSL_read(), SSL_peek(), or SSL_write() on B<ssl>. The value returned by
that TLS/SSL I/O function must be passed to SSL_get_error() in parameter
B<ret>.
In addition to B<ssl> and B<ret>, SSL_get_error() inspects the
current thread's OpenSSL error queue. Thus, SSL_get_error() must be
used in the same thread that performed the TLS/SSL I/O operation, and no
other OpenSSL function calls should appear in between. The current
thread's error queue must be empty before the TLS/SSL I/O operation is
attempted, or SSL_get_error() will not work reliably.
=head1 RETURN VALUES
The following return values can currently occur:
=over 4
=item SSL_ERROR_NONE
The TLS/SSL I/O operation completed. This result code is returned
if and only if B<ret E<gt> 0>.
=item SSL_ERROR_ZERO_RETURN
The TLS/SSL connection has been closed. If the protocol version is SSL 3.0
or TLS 1.0, this result code is returned only if a closure
alert has occurred in the protocol, i.e. if the connection has been
closed cleanly. Note that in this case B<SSL_ERROR_ZERO_RETURN>
does not necessarily indicate that the underlying transport
has been closed.
=item SSL_ERROR_WANT_READ, SSL_ERROR_WANT_WRITE
The operation did not complete; the same TLS/SSL I/O function should be
called again later. If, by then, the underlying B<BIO> has data
available for reading (if the result code is B<SSL_ERROR_WANT_READ>)
or allows writing data (B<SSL_ERROR_WANT_WRITE>), then some TLS/SSL
protocol progress will take place, i.e. at least part of an TLS/SSL
record will be read or written. Note that the retry may again lead to
a B<SSL_ERROR_WANT_READ> or B<SSL_ERROR_WANT_WRITE> condition.
There is no fixed upper limit for the number of iterations that
may be necessary until progress becomes visible at application
protocol level.
For socket B<BIO>s (e.g. when SSL_set_fd() was used), select() or
poll() on the underlying socket can be used to find out when the
TLS/SSL I/O function should be retried.
Caveat: Any TLS/SSL I/O function can lead to either of
B<SSL_ERROR_WANT_READ> and B<SSL_ERROR_WANT_WRITE>. In particular,
SSL_read() or SSL_peek() may want to write data and SSL_write() may want
to read data. This is mainly because TLS/SSL handshakes may occur at any
time during the protocol (initiated by either the client or the server);
SSL_read(), SSL_peek(), and SSL_write() will handle any pending handshakes.
=item SSL_ERROR_WANT_CONNECT, SSL_ERROR_WANT_ACCEPT
The operation did not complete; the same TLS/SSL I/O function should be
called again later. The underlying BIO was not connected yet to the peer
and the call would block in connect()/accept(). The SSL function should be
called again when the connection is established. These messages can only
appear with a BIO_s_connect() or BIO_s_accept() BIO, respectively.
In order to find out, when the connection has been successfully established,
on many platforms select() or poll() for writing on the socket file descriptor
can be used.
=item SSL_ERROR_WANT_X509_LOOKUP
The operation did not complete because an application callback set by
SSL_CTX_set_client_cert_cb() has asked to be called again.
The TLS/SSL I/O function should be called again later.
Details depend on the application.
=item SSL_ERROR_SYSCALL
Some I/O error occurred. The OpenSSL error queue may contain more
information on the error. If the error queue is empty
(i.e. ERR_get_error() returns 0), B<ret> can be used to find out more
about the error: If B<ret == 0>, an EOF was observed that violates
the protocol. If B<ret == -1>, the underlying B<BIO> reported an
I/O error (for socket I/O on Unix systems, consult B<errno> for details).
=item SSL_ERROR_SSL
A failure in the SSL library occurred, usually a protocol error. The
OpenSSL error queue contains more information on the error.
=back
=head1 SEE ALSO
L<ssl(3)|ssl(3)>, L<err(3)|err(3)>
=head1 HISTORY
SSL_get_error() was added in SSLeay 0.8.
=cut