[MODULE_PARAMETERS] # This section shall contain the values of all parameters that are defined in your TTCN-3 modules. # The GeoNetworking address of the IUT LibItsGeoNetworking_Pics.PICS_GN_LOCAL_GN_ADDR := { typeOfAddress := e_initial, stationType := e_unknown, stationCountryCode := 0, mid := '4c5e0c14d2ea'O } # IUT Station ID LibItsCommon_Pixits.PX_IUT_STATION_ID := 10143; LibItsGeoNetworking_Pixits.PX_GN_UPPER_LAYER := e_any [LOGGING] # In this section you can specify the name of the log file and the classes of events # you want to log into the file or display on console (standard error). LogFile := "../logs/%e.%h-%r.%s" FileMask := LOG_ALL | USER | DEBUG | MATCHING ConsoleMask := LOG_ALL | USER | DEBUG | MATCHING #FileMask := ERROR | USER | MATCHING | EXECUTOR_RUNTIME | VERDICTOP #ConsoleMask := ERROR | USER | MATCHING | EXECUTOR_RUNTIME | VERDICTOP LogSourceInfo := Stack LogEntityName:= Yes LogEventTypes:= Yes #TimeStampFormat := DateTime [TESTPORT_PARAMETERS] # In this section you can specify parameters that are passed to Test Ports. # BTP Layer # type : btpA|btpB # destination port: dst_port # source port : src_port # GN Layer # ll_address : GeoNetworking address of the TestSystem # latitude : latitude of the TestSystem # longitude : longitude of the TestSystem # beaconing : Set to 1 if GnLayer shall start beaconing # Beaconning timer expiry: expiry (ms) # Ethernet layer # Source MAC address: mac_src # Broadcast address : mac_bc # Ethernet type : eth_type # UDP layer (IP/UDP based on Pcap) # dst_ip : destination IPv4 address (aa.bb.cc.dd) # dst_port: destination port # src_ip : source IPv4 address (aa.bb.cc.dd) # src_port: source port # Pcap layer # Pcap filter: filter # Online mode: # Local NIC: nic # If set, online mode is used # Offline mode (nic is present but not set): # File to read : file # Frame offset : frame_offset # Time offset : time_offset # Save sent packet: save_mode=[0|1] # Single GeoNetworking component port system.geoNetworkingPort.params := "GN(ll_address=F8CAB8083918,latitude=43551050,longitude=10298730,beaconing=0,expiry=1000,its_aid=141)/ETH(mac_src=F8CAB8083918,mac_bc=FFFFFFFFFFFF,eth_type=8947)/PCAP(mac_src=BABEBABE0002,nic=,file=../../../testdata/test_10_beacon.pcap,filter=and ether proto 0x8947,frame_offset=0,save_mode=1)" #system.geoNetworkingPort.params := "GN(ll_address=F8CAB8083918,latitude=43551050,longitude=10298730,beaconing=0,expiry=1000,its_aid=141)/COMMSIGNIA(mac_src=70b3d5f2a1e3,bc=FFFFFFFFFFFF,target_host=10.200.1.101,target_port=7942,sourcePort=7943,its_aid=5,interface_id=2,tx_power=-32)/UDP(dst_ip=192.168.56.1,dst_port=12346,src_ip=192.168.156.4,src_port=12345)/ETH(mac_src=026f8338c1e5,mac_dst=0A0027000011,eth_type=0800)/PCAP(mac_src=0800275c4959,nic=enp0s8,filter=and udp port 12346)" # Multiple GeoNetworking component port Comp1.geoNetworkingPort.params := "GN(ll_address=F8CAB8083919,latitude=43551050,longitude=10298730,beaconing=1,expiry=1000,its_aid=141)/ETH(mac_src=F8CAB8083918,mac_bc=FFFFFFFFFFFF,eth_type=8947)/PCAP(mac_src=F8CAB8083919,nic=,file=../../../testdata/test_1_cam.pcap,filter=and ether proto 0x8947,frame_offset=0,save_mode=0)" Comp2.geoNetworkingPort.params := "GN(ll_address=F8CAB808391A,latitude=43551050,longitude=10298730,beaconing=1,expiry=1000,its_aid=141)/ETH(mac_src=F8CAB8083918,mac_bc=FFFFFFFFFFFF,eth_type=8947)/PCAP(mac_src=F8CAB808391A,nic=,file=../../../testdata/test_1_cam.pcap,filter=and ether proto 0x8947,frame_offset=0,save_mode=0)" # BTP port system.btpPort.params := "BTP(type=btpB,dst_port=2000,src_port=0)/GN(ll_address=F8CAB8083918,latitude=43551050,longitude=10298730,expiry=1000,its_aid=141)/ETH(mac_src=F8CAB8083918,mac_bc=FFFFFFFFFFFF,eth_type=8947)/PCAP(mac_src=F8CAB8083918,nic=,file=../../../testdata/test_1_cam.pcap,filter=and ether proto 0x8947,frame_offset=0)" # CAM port system.camPort.params := "CAM/BTP(type=btpA,dst_port=2001,src_port=0)/GN(ll_address=F8CAB8083918,latitude=43551050,longitude=10298730,expiry=1000,its_aid=141)/ETH(mac_src=F8CAB8083918,mac_bc=FFFFFFFFFFFF,eth_type=8947)/PCAP(mac_src=F8CAB8083918,nic=,file=../../../testdata/test_1_cam.pcap,save_mode=1,filter=and ether proto 0x8947,frame_offset=0)" # DENM port system.denmPort.params := "DENM/BTP(type=btpB,dst_port=2002,src_port=0)/GN(ll_address=F8CAB8083918,latitude=43551050,longitude=10298730,expiry=1000,its_aid=141)/ETH(mac_src=F8CAB8083918,mac_bc=FFFFFFFFFFFF,eth_type=8947)/PCAP(mac_src=F8CAB8083918,nic=,file=../../../testdata/test_1_denm.pcap,save_mode=1,filter=and ether proto 0x8947,frame_offset=0)" # IVIM port system.ivimPort.params := "IVIM/BTP(type=btpB,dst_port=2005,src_port=0)/GN(ll_address=F8CAB8083918,latitude=43551050,longitude=10298730,expiry=1000,its_aid=141)/ETH(mac_src=F8CAB8083918,mac_bc=FFFFFFFFFFFF,eth_type=8947)/PCAP(mac_src=F8CAB8083918,nic=,file=../../../testdata/test_1_ivim.pcap,save_mode=1,filter=and ether proto 0x8947,frame_offset=0)" # GeoNetworking UpperTester port based on UDP system.utPort.params := "UT_GN/UDP(dst_ip=192.168.56.1,dst_port=12346,src_ip=192.168.156.4,src_port=12345)/ETH(mac_src=026f8338c1e5,mac_dst=0A0027000011,eth_type=0800)/PCAP(mac_src=0800275c4959,nic=enp0s8,filter=and udp port 12346)" [EXECUTE] # GeoNetworking Req #TestCodec_GeoNetworking.tc_GeoNetReq_AnycastPacket #TestCodec_GeoNetworking.tc_GeoNetReq_BroadcastPacket #TestCodec_GeoNetworking.tc_GeoNetReq_UnicastPacket #TestCodec_GeoNetworking.tc_GeoNetReq_BeaconPacket #TestCodec_GeoNetworking.tc_GeoNetReq_LsRequestPacket #TestCodec_GeoNetworking.tc_GeoNetReq_LsReplyPacket # GeoNetworking Ind #TestCodec_GeoNetworking.tc_GeoNetInd_AnycastPacket #TestCodec_GeoNetworking.tc_GeoNetInd_BroadcastPacket #TestCodec_GeoNetworking.tc_GeoNetInd_ShbPacket #TestCodec_GeoNetworking.tc_GeoNetInd_UnicastPacket #TestCodec_GeoNetworking.tc_GeoNetInd_BeaconPacket # GeoNetworking port tests # To run the GeoNetworking port tests, use the offline mode and the test data provided. Use PcapLayer.save_mode to save sent packet into a file ##TestCodec_GeoNetworking.tc_GeoNet_Port # Use simulator t run this test ##TestCodec_GeoNetworking.tc_GeoNet_Port_utPort # Use simulator t run this test # GeoNetworking AC port #TestCodec_GeoNetworking.tc_GeoNet_Port_acPort_lpv #TestCodec_GeoNetworking.tc_GeoNet_acPort_getLongPositionVector_1 #TestCodec_GeoNetworking.tc_GeoNet_acPort_getLongPositionVector_2 #TestCodec_GeoNetworking.tc_GeoNet_Port_acPort_beaconing_1 #TestCodec_GeoNetworking.tc_GeoNet_Port_acPort_beaconing_2 #TestCodec_GeoNetworking.tc_GeoNet_Port_acPort_pass_beaconing_1 #TestCodec_GeoNetworking.tc_GeoNet_Port_acPort_pass_beaconing_2 #TestCodec_GeoNetworking.tc_GeoNet_MultiPort # GeoNetworking UpperTester #TestCodec_GeoNetworking.tc_GeoNet_UtGnInitialize #TestCodec_GeoNetworking.tc_GeoNet_UtGnChangePosition #TestCodec_GeoNetworking.tc_GeoNet_UtGnTrigger_GeoUnicast_1 #TestCodec_GeoNetworking.tc_GeoNet_UtGnTrigger_GeoUnicast_2 #TestCodec_GeoNetworking.tc_GeoNet_UtGnTrigger_GeoBroadcast_1 #TestCodec_GeoNetworking.tc_GeoNet_UtGnTrigger_GeoBroadcast_2 #TestCodec_GeoNetworking.tc_GeoNet_UtGnTrigger_GeoAnycast_1 #TestCodec_GeoNetworking.tc_GeoNet_UtGnTrigger_GeoAnycast_2 #TestCodec_GeoNetworking.tc_GeoNet_UtGnTrigger_Shb_1 #TestCodec_GeoNetworking.tc_GeoNet_UtGnTrigger_Shb_2 #TestCodec_GeoNetworking.tc_GeoNet_UtGnTrigger_Tsb_1 #TestCodec_GeoNetworking.tc_GeoNet_UtGnTrigger_Tsb_2 # Btp PDU #TestCodec_Btp.tc_Btp_A_Without_Payload #TestCodec_Btp.tc_Btp_A #TestCodec_Btp.tc_Btp_B #TestCodec_Btp.tc_BtpReq_A # Btp Port #TestCodec_Btp.tc_Btp_Port # CAM PDU tests #TestCodec_CAM.tc_CamReq #TestCodec_CAM.tc_CamInd_1 #TestCodec_CAM.tc_CamInd_2 # CAM port tests # To run the CAM port tests, use the offline mode and the test data provided. Use PcapLayer.save_mode to save sent packet into a file #TestCodec_CAM.tc_Cam_Port # CAM UpperTester #TestCodec_CAM.tc_Cam_UtCamInitialize #TestCodec_CAM.tc_Cam_UtCamChangePosition #TestCodec_CAM.tc_Cam_UtCamChangeCurvature #TestCodec_CAM.tc_Cam_UtCamChangeSpeed #TestCodec_CAM.tc_Cam_UtCamSetAccelerationControlStatus #TestCodec_CAM.tc_Cam_UtCamSetExteriorLightsStatus_lowBeamHeadlightsOn #TestCodec_CAM.tc_Cam_UtCamSetExteriorLightsStatus_leftTurnSignalOn #TestCodec_CAM.tc_Cam_UtCamSetExteriorLightsStatus_daytimeRunningLightsOn #TestCodec_CAM.tc_Cam_UtCamSetExteriorLightsStatus_parkingLightsOn #TestCodec_CAM.tc_Cam_UtCamChangeHeading #TestCodec_CAM.tc_Cam_UtCamSetDriveDirection #TestCodec_CAM.tc_Cam_UtCamChangeYawRate #TestCodec_CAM.tc_Cam_UtCamChangeYawRate_negative #TestCodec_CAM.tc_Cam_UtCamSetStationType #TestCodec_CAM.tc_Cam_UtCamSetVehicleRole #TestCodec_CAM.tc_Cam_UtCamSetDangerousGoods #TestCodec_CAM.tc_Cam_UtCamSetLightBarSirene #TestCodec_CAM.tc_Cam_UtCamTriggerResult #TestCodec_CAM.tc_Cam_UtCamEventInd_1 #TestCodec_CAM.tc_Cam_UtCamEventInd_2 # DENM PDU ##TestCodec_DENM.tc_DenmReq ##TestCodec_DENM.tc_DenmInd # DENMM port tests # To run the DENM port tests, use the offline mode and the test data provided. Use PcapLayer.save_mode to save sent packet into a file #TestCodec_DENM.tc_Denm_Port ##TestCodec_DENM.tc_Denm_Port_utPort # DENM UpperTester #TestCodec_DENM.tc_Denm_UtDenmInitialize #TestCodec_DENM.tc_Denm_UtDenmChangePosition #TestCodec_DENM.tc_Denm_UtDenmChangePseudonym #TestCodec_DENM.tc_Denm_UtDenmTrigger_1 #TestCodec_DENM.tc_Denm_UtDenmTrigger_2 #TestCodec_DENM.tc_Denm_UtDenmUpdate_1 #TestCodec_DENM.tc_Denm_UtDenmUpdate_2 #TestCodec_DENM.tc_Denm_UtDenmTriggerResult #TestCodec_DENM.tc_Denm_UtDenmUpdateResult #TestCodec_DENM.tc_Denm_UtDenmEventInd_1 #TestCodec_DENM.tc_Denm_UtDenmEventInd_2 # IVIM PDU #TestCodec_IVIM.tc_IvimReq #TestCodec_IVIM.tc_IvimInd_1 #TestCodec_IVIM.tc_IvimInd_2 # IVIM port tests # To run the IVIM port tests, use the offline mode and the test data provided. Use PcapLayer.save_mode to save sent packet into a file #TestCodec_IVIM.tc_Ivim_Port # IVIM UpperTester #TestCodec_IVIM.tc_Ivim_UtIvimInitialize #TestCodec_IVIM.tc_Ivim_UtIvimTrigger_1 #TestCodec_IVIM.tc_Ivim_UtIvimTrigger_2 #TestCodec_IVIM.tc_Ivim_UtIvimUpdate #TestCodec_IVIM.tc_Ivim_UtIvimTermination # Security tests # Functions TestCodec_SecuredFuntions.tc_sha256_1 TestCodec_SecuredFuntions.tc_sha384_1 TestCodec_SecuredFuntions.tc_f_generate_key_pair_1 TestCodec_SecuredFuntions.tc_f_generate_key_pair_2 TestCodec_SecuredFuntions.tc_f_generate_key_pair_3 TestCodec_SecuredFuntions.tc_f_signWithEcdsaNistp256WithSha256_1 TestCodec_SecuredFuntions.tc_f_verifyWithEcdsaNistp256WithSha256_1 TestCodec_SecuredFuntions.tc_f_verifyWithEcdsaNistp256WithSha256_2 TestCodec_SecuredFuntions.tc_f_verifyWithEcdsaNistp256WithSha256_3 TestCodec_SecuredFuntions.tc_f_signWithEcdsaBrainpoolp256WithSha256_1 TestCodec_SecuredFuntions.tc_f_verifyWithEcdsaBrainpoolp256WithSha256_1 TestCodec_SecuredFuntions.tc_f_verifyWithEcdsaBrainpoolp256WithSha256_2 TestCodec_SecuredFuntions.tc_f_verifyWithEcdsaBrainpoolp256WithSha256_3 #TestCodec_SecuredFuntions.tc_f_signWithEcdsaBrainpoolp384WithSha384_1 #TestCodec_SecuredFuntions.tc_f_verifyWithEcdsaBrainpoolp384WithSha384_1 #TestCodec_SecuredFuntions.tc_f_verifyWithEcdsaBrainpoolp384WithSha384_2 #TestCodec_SecuredFuntions.tc_f_verifyWithEcdsaBrainpoolp384WithSha384_3 # Certificates TestCodec_Certificates.tc_at_certificate_sha256_1 TestCodec_Certificates.tc_at_certificate_sha256_2 #TestCodec_SecuredMessages.tc_secured_message_signed [MAIN_CONTROLLER] # The options herein control the behavior of MC. KillTimer := 10.0 TCPPort := 0 LocalAddress := 127.0.0.1 TCPPort := 12000 NumHCs := 1